Related Manuals for Artila M-606
Summary of Contents for Artila M-606
- Page 1 M-606 Linux ARM9 Single Board Computer User Guide Version 1.0 Copyright © Artila Electronics Co., Ltd. All Rights Reserved.
-
Page 3: Table Of Contents
3.12 GPIO Control ........................6 Artila Utility Software ....................7 Beep ............................ 7 update ..........................7 Web Page Directory ......................7 Reboot ..........................7 Remote Display Control ...................... 7 ActiveSync .......................... 8 Install M-606 SDK ....................... 8 Install USB WLAN dongle ....................9... -
Page 5: Introduction
M-606 User Guide 1. Introduction M-606 is a WinCE ready Single Board Computer featuring four serial ports, LCD TTL/LVDS Interface, 10/100Mbps Ethernet, USB port and SD socket for flash disk expansion. The pre-install WinCE 6.0 makes M-606 ready for your application development using Microsoft Visual Studio. -
Page 6: Layout
M-606 User Guide 2. Layout COM5 COM6 COM2 Touch J7: +12V J8: +5V Audio JP1/3/5 JP8/7 USB Port COM3 COM4/IO Please refer to Appendix Pin Assignment: J1 Connector: CSI-4585-400R J4 Connector: CSI-4585-300R J2 Connector: CSF-2481-401R (On the back) -
Page 7: Pin Assignment And Definition
M-606 User Guide 3. Pin Assignment and Definition 3.1 Factory Default Settings LAN IP Address: DHCP LCD Resolution: 800 x 480 16-bit color User disk: NandFlash Web page path: NandFlash\www Autoexec path: NandFlash 3.2 Power on and System boot up Once Matrix-604 correctly power on, it will take about 30 seconds to hear a BEEP which means WinCE is successfully boot up. -
Page 8: Lcd Brightness Control
M-606 User Guide 3.5 LCD Brightness Control To configure the LCD brightness, you can use the utility software at Program/Backlight Control as shown followed: 3.6 Network Settings To configure the network setting by serial console, you can use command ifconfig as followed. To check current network configuration, you can use command ipconfig. -
Page 9: Ftp Configuration
WWW is for web page and autoexec.bat is for auto run program. If you have a USB disk plugged in Matrix-604, you will find a new folder Hard Disk available. 3.11 Serial Ports Configuration The serial port of M-606 is mapped as followed: Serial 1=> USB Console (ActiveSync) Serial 2=> Console (RS-232) Serial 3=>... -
Page 10: Gpio Control
M-606 User Guide 3.12 GPIO Control M-606 comes with five GPIO which share the serial console port connector. Use gpioctl command to control the GPIO port. The I/O number starts from #1 to #5 and can be configured as input or output independently. -
Page 11: Artila Utility Software
Reboot command is used to reboot the system. 4.5 Remote Display Control M-606 comes with WinCE remote display control software. You can find this software on Artila FTP at \tool\cerhost.exe. Choose connect to find and connect M-606 and ok to connect it. You can also enter the IP address of M-606 to connect it. -
Page 12: Activesync
ActiveSync provides an easy way to transfer files between PC and M-606. 4.7 Install M-606 SDK M-606 WinCE 6.0 SDK is located at Artila FTP. You need to install Microsoft Studio 2005 before installing M-606 SDK. Choose M-606_CE_SDK for the smart device application and click the device option. -
Page 13: Install Usb Wlan Dongle
M-606 User Guide 4.8 Install USB WLAN dongle M-606 supports USB WLAN dongle which uses Ralink RT2870 Wireless LAN controller. While plug in USB WLAN dongle, you will see the new USB device detected. Follow the screen 1, 2, 3 to configure the Wireless LAN. - Page 14 M-606 User Guide Screen 3 ‧10‧...
Need help?
Do you have a question about the M-606 and is the answer not in the manual?
Questions and answers