1. Manuals
  2. Brands
  3. Aopos Manuals
  4. Printer
  5. D5000
  6. User manual

Aopos D5000 User Manual

Impact dot matrix printer
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
USER
USER
GUIDE
GUIDE
USER
USER GUIDE
GUIDE
AOPOS
AOPOS
AOPOS
AOPOS
D5000
D5000
D5000
D5000
Impact
Dot
Matrix
Impact
Impact
Impact Dot
Dot
Dot Matrix
Matrix Printer
Matrix
AOPOS
AOPOS
SYSTEMS
SYSTEMS
AOPOS
AOPOS SYSTEMS
SYSTEMS S.A.
Printer
Printer
Printer
S.A.
S.A.
S.A.
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the D5000 and is the answer not in the manual?

Questions and answers

Related Manuals for Aopos D5000

Summary of Contents for Aopos D5000

  • Page 1 USER USER GUIDE GUIDE USER USER GUIDE GUIDE AOPOS AOPOS AOPOS AOPOS D5000 D5000 D5000 D5000 Impact Matrix Printer Impact Impact Impact Dot Dot Matrix Matrix Matrix Printer Printer Printer AOPOS AOPOS SYSTEMS SYSTEMS S.A. S.A. AOPOS AOPOS SYSTEMS SYSTEMS S.A.
  • Page 2 AOPOS AOPOS SYSTEMS S.A.. any means, means, means, without without without the the written...

  • Page 3: Table Of Contents

    TABLE TABLE TABLE TABLE OF OF CONTENTS CONTENTS CONTENTS CONTENTS Chapter I Introduction ........................5 1.1TechniqueSpecification ......................5 1.2Printing Paper ......................... 5 1.3Printing Character ........................5 1.4Interface Form ........................6 1.5Power and Operating Environmental Conditions ..............6 1.6 Dimension and Weight ......................6 Chapter Ⅱ...
  • Page 4 ESC c 3 n ........................23 ESC c 4 n ........................24 ESC c 5 n ........................25 ESC d n ........................25 ESC e n ........................26 ESC p m t1 t2 ......................26 ESC t n ........................26 GS ( A PL PH n m .....................

  • Page 5: Chapter I Introduction

    Chapter Chapter I I I I Introduction Introduction Chapter Chapter Introduction Introduction 1.1Technique Specification 1.1Technique 1.1Technique 1.1TechniqueSpecification Specification Specification Item Parameter Printing Mode 9-pin serial configuration Printing Density 42CPL-210(Full dot)/420(Half dots) 40CPL-200(Full dot)/400(Half dots) Printing Speed Approximately 7.1 Line/Sec (printing 16 characters pen line) Approximately 4.1 Line/Sec(printing 40 characters pen line);...

  • Page 6: Dimension And Weight

    Item Parameter Serial Interface D-SUB 25 thread socket(female), Compatible with RS-232; Support DTR/DSR; Asynchronous Serial Communication: 9600bps/19200bps; 8 digit data; 1digit stop Parallel Interface 8 digit Parallel Interface, BUSY handshake protocol, interface socket use D-SUB25 thread socket(male) Cash Drawer DC 24V, 2 A, 6 Thread RJ-11 Socket 1.5Power 1.5Power Operating...

  • Page 7: Chapter Ⅱ Installation And Operation

    AOPOS D5000 Control Control Board Board 2.2 Control Control Board Board Icod D5000 Printer Board has one keys and three indicator lights, the graphic as follows: The sketch sketch sketch sketch graphic graphic graphic graphic of of of of control...

  • Page 8: Interface Connection

    Connection Connection 2.3.2 2.3.2 Parallel Parallel Interface Interface Connection Connection. The parallel interface of Icod D5000 printer is 8 digit parallel interface, supporting BUSY handshaking, and the interface socket used DB25 thread socket(male). Interface pin Assignments Signal Signal Source Function...

  • Page 9: Cash Drawer Interface

    Figure 2-3.2 Parallel Interface Signal Time Sequence Figure Figure Figure 2.3.3 Cash drawer interface 2.3.3 2.3.3 2.3.3 Cash Cash Cash drawer drawer drawer interface interface interface The cash drawer interface of D5000 printer used RJ-11, 6 thread socket, as the diagram 2-3.3...
  • Page 10 Figure Cash Drawer Interface Drawer Kick-out Connector Pin Assignments: Pin No. Signal Frame GND Drawer kick-out drive signal 1 Drawer open/close signal +24V Drawer kick-out drive signal 2 Signal ground 2.4Panel 2.4Panel Buttons Buttons 2.4Panel 2.4Panel LED LED and and Buttons Buttons Indicator: Power LED: Green...
  • Page 11 Incorrect cutter, error light flashed one time and stopped a while, then repeated this phenomenon till error exclusion. ■ No paper light, when the paper not be set well, or no paper, the light will be bright. ■ Under the black mark pattern, pressing the key, printer paper rolled the paper to the head of the next page;...
  • Page 12 Notes: 1. When installing paper, needs to clip the end of paper and inserts to paper entrance exactly, Puts your strength balance, moves the end of paper ahead till feeding paper motor revolved, and takes out paper by itself. When installing paper if the end of paper jams in the paper entrance, comes out paper jams, waits self-moving paper motor stopping and pulls paper out.

  • Page 13: Chapter Ⅲ Print Table

    Chapter Ⅲ Print Table 3.1 Printer Printer Printer Printer set set command command command command Printer set command. The set content of this command won’t be lost if turning the power off. ASCⅡ DECIMAL Parameter Illustration Parameter Illustration n=1 Printer with cutter m=6 Choose Choose Choose...

  • Page 14: Command Illustration

    e serial n=0 9600bps baud rate Default n=0 9600bps 3.2 Command Command Command Command Illustration Illustration Illustration Illustration Command Illustration Horizontal tab Print and line feed Print and carriage return DLE EOT n Real-time status transmission DLE ENQ n Real-time request to printer ESC SP n Set right-side character spacing ESC ! n...
  • Page 15 FS 2 c1 c2 Define user-defined Chinese characters dl……dk FS ? c1 c2 Cancel user-defined Chinese characters FS S n1 n2 Set left-and right-side Chinese character spacing FS W n Turn quadruple-size mode on/off for Chinese characters GS ( F PL PH a m Set black mark offset nL nH GS FF...
  • Page 16 EOT n n n n DLE EOT Transmit real-time status Form ASCⅡ: DLE EOT n DECIMAL: 16 HEX: 10 04 Description Transmits the selected printer status specified by n in real time(Just serial model), according to following parameters: n = 1: Transmit printer status n = 2: Transmit offline status n = 3: Transmit error status n = 4: Transmit paper roll sensor status...
  • Page 17 Unused Undefined Press No feed paper The processing feed paper of pressing key feeding paper Unused paper With paper Without paper stop printing stop printing Error status No error Error occurred Unused n=3: n = 3: Error status Function Datum OFF/ON Unused Unused Mechanical error...
  • Page 18 Form ASCⅡ: DLE ENQ n DECIMAL: 16 HEX: 10 Description This command only effects to D5000 serial model, when receiving this command, according to n parameter stipulation and answer the host computer’s operational request. Parameter n took number 0, 2...
  • Page 19 Function Datum Character model 5×7 7×7 chosen Undefined Undefined Undefined Double height Cancel Double width Cancel Undefined Underline Cancel Window default n=0, choose 5 × 7 dot, normal character, no underline. Esc % % % % n n n n Select/cancel user-defined character set Form ASCⅡ: Esc % n...
  • Page 20 1. When ESC @ is executed 2. When deleted by ESC ? 3. When the printer is reset or turned off. ESC * * * * Select bit-image mode Form ASCⅡ: ESC * m nl n2〔d〕nl+256×n2 DECIMAL: 27 42 m nl n2〔d〕nl+256×n2 HEX: 1B 2A m nl n2〔d〕nl+256×n2 Description Selects a bit-image mode using m for the number of dots...
  • Page 21 ESC – – – – n n n n Turn underline mode on/off Form ASCⅡ: ESC – n DECIMAL: 27 45 n HEX: 1B 2D n Description When n = 0 or 48, underline mode is turned off. When n = 1 or 49, underline mode is turned on. ESC 2 2 2 2 Set character line spacing 1/6 inch Form...
  • Page 22 Clear data in the print buffer; Resets the printer mode to the mode that was in effect when the power was turned on. ESC D D D D Set horizontal tab position Form ASCⅡ: ESC D 〔n〕k NUL DECIMAL: 27 68 〔n〕k 0 HEX: 1B 44 〔n〕k 00 Description n specifies the column number for setting a horizontal tab...
  • Page 23 ×0.176 ㎜). n=0～255 The order only effects to print this line, not change the line spacing datum which set by ESC2, ESC3 order. ESC K K K K n n n n Print and reverse feed paper n/144 inches Form ASCⅡ: ESC K n DECIMAL: 27 75 n HEX: 1B 4B n...
  • Page 24 ESC U U U U n n n n Turn unidirectional printing mode on/off Form ASCⅡ: ESC U n DECIMAL: 27 85 n HEX: 1B 55 n Description Turn unidirectional printing mode on/off. n=0 ～ 255, only effects to the lowest bit. n=<××××××××1>B, turn on unidirectional printing mode and turn on bidirectional printing mode.
  • Page 25 not set this switch, the printer won’t send the signal of paper will be ended. Window default is n=<****1111>B. ESC c c c c 4 4 4 4 n n n n Select paper sensor(s) to stop printing Form ASCⅡ: ESC c 4 n DECIMAL: 27 99 52 n HEX: 1B 63 34 n Descriptio...
  • Page 26 When n=<*******0>B, the panel button is enabled. When n=<*******1>B, the panel button is disabled. Default n=0. ESC d d d d n n n n Print and feed paper n character line Form ASCⅡ: ESC d n DECIMAL: 27 100 n HEX: 1B 64 n Description Print the date in the print buffer and feeds the paper n...
  • Page 27 ESC t t t t n n n n Select character set Form ASCⅡ: ESC t n DECIMAL: 27 116 n HEX: 1B 74 n Description Select character set 0 or 1.n=0～1. Window default n=0, Select character set 0(IBM character set 2) GS ( ( ( ( A A A A PL PH n n n n m m m m PL PH...
  • Page 28 s on the parameter of GS ( F order command. GS r r r r n n n n Transmit status Form ASCⅡ: GS r n DECIMAL: 29 114 n HEX: 1D 72 n Description Transmits the status specified by n as follow (only for serial printer).
  • Page 29 When printer test that the host computer DSR signal is effective, will upload condition byte, Or, wait forever. The host computer send this command means downloading to printer received buffer, waiting for printer command explained execution. So the time of printer uploading condition may longer than receiving this order and uploading condition.
  • Page 30 Description Using n as follows: Function Datum 0, 1 Undefined Double width printing Cancel Double height printing Cancel 4, 7 Undefined Default n=0 FS & & & & Select Chinese characters mode Form ASCⅡ: FS & DECIMAL: 28 38 HEX: 1C 26 Description Printer received this command, select Chinese characters mode.
  • Page 31 FS 2 2 2 2 c1 d1… … … … dk c1 c2 c2 d1 Define user-defined Chinese Form ASCⅡ: FS 2 c1 c2 d1…dk DECIMAL: 28 50 c1 c2 d1…dk HEX: 1C 32 c1 c2 d1…dk Description c1=FEH c2=A1h～FEH k=32 ●...
  • Page 32 Window default n1=0, n2=0 FS W W W W n n n n Set/cancel Chinese quadruple-size mode Form ASCⅡ: FS W n DECIMAL: 28 87 n HEX: 1C 57 n Description The lowest n is 0, cancel Chinese quadruple-size mode The lowest n is 1, set Chinese quadruple-size mode Default n=0` GS ( ( ( ( F F F F pL...
  • Page 33 operation of GS FF and GS V order is effect. ● When executing GS FF order, set started printing position offset(a=1) is effect. ● When executing GS V m order, set cut/tear paper position offset(a=2) is effect. b. Illustration about cutting/tearing paper position offset and starting printing position offset.
  • Page 34 ck mark. Cutting position ● Start printing position offset(the parameter of a=1) is C＋ ● Tear position offset(the parameter of a=1) is D＋A. ④ Notes: The unit of above A、B、C、D、L is ㎜, transform to GS CF’s nl, nh need to divide into 0.176. Notes: When calculate black mark offset parameter, if offset over the length L of printing single bill, need to decrease with L, until the final offset is not more than L, Or, the...
  • Page 35 assured printing started position. When black mark at the present printing started position, not execute feeding paper operation. With cutter and cutter set by half pattern, the printer won’t be executed reverse feed paper.

Table of Contents