Table of Contents
Advertisement
Changes in this Issue
• Add New Model
* New Manual (First Issue)
Service
Information
© 2016 Reg. Office: Peterborough PE2 9JB Registered in London: 106725
Whirlpool UK Appliances Ltd
5407926 Issue 1
C00384298 ~ SM032030
WASHING
MACHINE
SMALL DIGIT
Model
Covered
WMXTF922GUK
April 2016
Comm.
Code
85885
Advertisement
Table of Contents
Related Manuals for Hotpoint WMXTF922GUK
Summary of Contents for Hotpoint WMXTF922GUK
-
Page 1: Washing Machine
WASHING MACHINE SMALL DIGIT Model Comm. Changes in this Issue Covered Code • Add New Model WMXTF922GUK 85885 * New Manual (First Issue) Service Information Whirlpool UK Appliances Ltd © 2016 Reg. Office: Peterborough PE2 9JB Registered in London: 106725... -
Page 2: Safety & Servicing Notes
Indesit Company SAFETY NOTES & GENERAL SERVICING ADVICE 1. This manual is NOT intended as a comprehensive repair/maintenance guide to the appliance. 2. It should ONLY be used by suitably qualified persons having technical competence applicable product knowledge and suitable tools and test equipment. 3. -
Page 3: Table Of Contents
Whirlpool UK Appliances Ltd INDEX Safety & Servicing Notes............2 Index and Manufacturing Serial Number Information . -
Page 4: Specifications & Introduction Dates
Indesit Company SPECIFICATIONS Models Covered WMXTF922GUK (85885) Colour G = Graphite Height 850 mm Width 595 mm Dimensions Depth 605 mm Weight 73.4 kg Packed approx. 75.0 kg Country of Origin Factory 80 - Comunanza, Italy Electrical Supply 220 - 240 Volt AC @ 50 Hz Fuse 13 amp... - Page 5 Whirlpool UK Appliances Ltd WMXTF922GUK Service Manual UK English 5 of 27...
- Page 6 Indesit Company INTRODUCTION DATES Model: WMXTF922GUK First Produced: October 2013 Location: Comunanza Factory (80) - Italy Industrial Code: 80858850100 Controls: 3 Phase - Arcadia 2 Model: WMXTF922GUK First Produced: May 2014 Location: Comunanza Factory (80) - Italy Industrial Code: 80858850195...
-
Page 7: Installation
Whirlpool UK Appliances Ltd INSTALLATION Unpacking 1. Unpack the washing machine and check whether the it has been damaged during transport. If this is the case, do not install it and contact the retailer. 2. Remove the four protective screws (transit bolts) and the rubber washer with the respective spacer, situated on the rear of the appliance (see Figures below). - Page 8 Indesit Company Connecting the water inlet hose. Before making the water Connect the other end of connection to the 3/4" the water inlet hose to the thread, allow the water washing machine, freely from the supply tap screwing it onto the cold until it is perfectly clear.
-
Page 9: Installation
Whirlpool UK Appliances Ltd DRAINAGE CONNECTIONS A. Connect the drain hose, without kinking it, to a Fig. 1 draining duct or a wall drain fixed at a height between 65 and 100 cm from the floor. See Fig. 1. B. Alternatively, place it over the edge of a basin, sink or tub, fastening the hose supplied to the tap. -
Page 10: First Wash Cycle / Cleaning The Machine
Indesit Company FIRST WASH CYCLE / CLEANING THE MACHINE Cleaning the Washing Machine • The outer parts and rubber components of the appliance can be cleaned using a soft cloth soaked in lukewarm soapy water. Do not use solvents or abrasives. •... -
Page 11: Controls & Options
Whirlpool UK Appliances Ltd CONTROLS DIGIT MODEL (image below for guidance only) Wash Cycle Selector Knob Cleaning Action Button Child Lock Button Temperature Button Display Start/Pause Button & Indicator Light Option Button & Indicator Light Spin Button Delay Timer Button On-Off Button ON-OFF / SELECTING A PROGRAMME The machine is switched on by pressing the ON-OFF button. - Page 12 Indesit Company TO STOP OR CHANGE A PROGRAMME Press the ON-OFF button for approximately 3 seconds. Select PUMP OUT on the programme dial. Switch on and re-start. When the machine has finished emptying. Press the ON-OFF button. Select a new programme and re-start. NOTE: If you cancel a HOT wash or Dry programme, take care when removing the laundry, it may still be VERY HOT.
- Page 13 Whirlpool UK Appliances Ltd OPTIONS Options are selected by pressing the button and confirmed by illumination an orange LED situated in the button. If an option is not available with a programme, the LED will flash and a bleeping noise will be heard when pressing the button.
- Page 14 Indesit Company CUSTOMISE THE WASH CYCLE Use the relevant buttons: Modify the Temperature and/or Spin Speed The machine automatically displays the maximum temperature and spin speed values set for the selected cycle, or the most recently-used settings if they are compatible with the selected cycle. The temperature can be decreased by pressing the button, until the cold wash 'OFF' setting is reached.
-
Page 15: Controls Information
Whirlpool UK Appliances Ltd CONTROLS INFORMATION A single control board located at the back of the machine contains all the circuitry to control the machine and interfaces with the programme selector, option buttons and LEDs located on the console panel. The control board has an access port to the rear of the machine. Programmes are selected by turning the rotary switch to one of the 16 positions. -
Page 16: Wash Cycles
Indesit Company WASH CYCLES Service Manual UK English 16 of 27... -
Page 17: Special Wash Cycles
Hotpoint is the first washing machine brand to be approved by The Woolmark Company for Apparel Care- Platinum for its washing performance and consumption of energy and... -
Page 18: Wiring Details
WIRING DIAGRAM 220 - 240 Vac Mains Filter Linear Water valves Pressure Motor Switch Wash Pre- (3 phase) Wash Pump Wash Wash Tacho Heater with ? ? ? ? thermal fuse Brown Blue Brown Blue JE11 Resist Deviat Neutral Live Triac Neutral Triac... -
Page 19: Wiring Legend
Whirlpool UK Appliances Ltd WIRING LEGEND Solenoid valve Neutral or Terminal board Drying solenoid valve Drain pump Hot water solenoid valve Heating element Cold water solenoid valve Heating element Wash solenoid valve Main earth Prewash solenoid valve Neutral or Terminal board Door switch Line or Lamp Microdelay device... -
Page 20: Wiring Connections
Indesit Company WIRING CONNECTIONS DISPLAY PRESSURE SWITCH 0.35 X 1550 JE15 0.35 X 1550 0.35 X 1550 Display MODULE 0.35 X 1550 Press/ celeste 0.35 X 1390 Sens 0.35 X 1550 celeste 0.35 X 1390 celeste 0.35 X 1390 MOTOR MAINS FILTER 0.50 X 730 1JE7... -
Page 21: Power Module Connections
Whirlpool UK Appliances Ltd POWER MODULE CONNECTIONS Auto Test Socket JE11 JE15 Service Manual UK English 21 of 27... -
Page 22: Error Codes & Possible Causes
Indesit Company FAULT FINDING - Factory 30 - Arcadia Models IMPORTANT NOTE: Disconnect the machine from Electricity Supply before any testing. General Information If the machine has an Earth Fault it can display erroneous fault codes. Repair any Earth Faults on the machine before using the code guide on the previous page. Some faults will not show up as error codes:- The module will not show up a fault if the water to the machine is turned off or if the solenoid valves are open circuit. - Page 23 Whirlpool UK Appliances Ltd FAULT CAUSE SERVICE ACTIONS - If status type pressure switch, check component directly; - Check effi ciency of connector contacts on PCB; - Check pressure switch wiring; - Check continuity of pump on connector pins 4 and 5 (in case of classic door lock), ensuring that impedance value is 170 +/- 10%;...
- Page 24 Indesit Company FAULT CAUSE SERVICE ACTIONS - Check the condenser fi lter is not clogged; - Check there is no fl uff in the blower fan; If the components are clean or the problem persists despite cleaning, then: - Check the effi ciency of the connector contacts of the NTC on the main PCB;...
-
Page 25: Dismantling Instructions
Whirlpool UK Appliances Ltd DISMANTLING INSTRUCTIONS & SAFETY NOTES SAFETY NOTES Ensure that the appliance is disconnected from the electrical supply before dismantling. Beware of sharp edges on metal panels, plastic mouldings, and pressed parts. Some fixings (especially those into plastic) must be tightened to the correct specification using a suitable torque wrench. - Page 26 Indesit Company Top Concrete Weight Remove the top cover (A). Remove the 3 fixing bolts and lift clear. Dispenser/Valve Assembly Remove the top cover (A). Remove the drawer. Remove the screws securing the dispenser to the control panel. Remove the inlet valve fixing screws to the rear of the cabinet. Remove the control panel (C).
- Page 27 Whirlpool UK Appliances Ltd Insert slide Part No. C00222704 (5600155), inside the cabinet at the rear of the drum. Using suitable protection lay appliance on its back. Remove 2 x 10 mm nuts securing the shock absorbers to the base of the cabinet. Remove the tank/pump hose.