Table of Contents
Advertisement
ESPAÑOL
ADVERTENCIA:
PARA EVITAR RIESGO DE INCENDIO O DE DESCARGAS
ELÉCTRICAS, NO EXPONGA ESTE APARATO A LLUVIA O HUMEDAD.
NO QUITE LA CUBIERTA. LOS PILOTOS LUMINOSOS ESTÁN
SOLDADOS EN SU LUGAR. NO HAY PIEZAS ÚTILES EN SU
INTERIOR. EN CASO DE REPARACIONES, ACUDA SIEMPRE A
PERSONAL DE REPARACIONES CUALIFICADO.
ADVERTENCIA
RIESGO DE DESCARGAS
ELÉCTRICAS. NO ABRIR
ADVERTENCIA: PAPR REDUCIR
El símbolo del relámpago
con punta de flecha dentro
EL RIESGO DE DESCARGAS
de un triángulo equilátero
ELÉCTRICAS, NO RETIRE LA
pretende advertir al usuario
CUBIERTA (NI LA PARTE
de la presencia de "voltaje
peligroso" sin aislar dentro
TRASERA) NO HAYPIEZAS QUE
del producto. que puede
PUEDA USAR EN SU INTERIOR.
tener la suficiente magnitud
EN CASO DE REP ARACIONES
como para suponer un riesgo
ACUDA SIEMPRE AL SERVICIO
de electrocución para las
personas.
TÉCNICO.
Especificaciones
Rango de frecuencias
: MW 522 - 1620 KHz
: FM 87.5 - 108 MHz
Puerto USB 2.0
: VelocidadÊmáxima 512MB -4GB
(Soporta FAT16, FAT32)
Consumo de energía
: 23W
Antenas
: Cable de antena externo para FM
: Antena de ferrita incorporada para AM
Corriente eléctrica
: AC 230V ~ 50Hz
Tamaño altavoces
: 4" 4 ohm tipo dinámico x 2
*DISEÑO Y ESPECIFICACIONES SUJETOS A CAMBIOS SIN PRECIO AVISO.
El signo de exclamación
dentro de un triángulo
equilátero pretemde advertir
al usuario de la presencia
de instrucciones de
funcionamiento
(reparaciones) importantes
en el manual que acompaña
el aparato.
50
ENGLISH
OPTIONAL EXTERNAL SPEAKERS
1. With your new radio, you have the option of adding external speakers.
2. The speaker jacks for external speakers are located on the back of the radio.
Along with the speaker jacks is a switch labeled Int./Ext.
When using external speakers, this switch must be switched to the EXT. position. Doing this turns off the internal speakers
in the radio and redirects the power to the external speakers.
3. If you decide not to use the external speakers, be sure the switch is switch to INT.
AUDIO CONNECTIONS
AUX INPUT
Using the Aux Input allows you to hook up additional external audio
components and listen to them through your unit. Any component
with an audio output such as a Tuner, can be connected by using
the correct cables (not included). This unit uses standard RCA
cables. Simply plug the red and white connectors on one end of
the cable to the red and white Aux In jacks on the back of your unit.
The other end of the cable will plug into the Audio Output jack on
the external component. For more information on hooking up the
external component, see the owner s manual for that component.
TROUBLESHOOTING
There is no power
1. Make sure radio is plugged in correctly.
2. Look at the STAND BY INDICATOR and check to see if it is red.
3. If the red light is on, press the POWER button /
There is no sound
1. Make sure the mute function is turned off.
2. Check that the volume is turned up by pressing VOLUME UP button /
Note: Volume range on some units start at level 15 and ends at level 40.
3. Make sure INT./EXT. switch on back of radio is switched to INT. (Unless you are using external speakers, in which
case it should be on EXT. )
4. Check to make sure power is turned on.
CD does not play
1. Check to make sure CD is inserted correctly (label side facing up).
2. Check to see that surface of CD is clean.
3. Make sure function switch is set to CD mode.
USB - There is no music playing when PLAY/PAUSE (USB) is pressed.
1. Make sure the MP3 device/Flash Drive has stored music files.
2. The unit will only play Flash Drives up to 512MB – 4GB
3. Reset USB by switching the unit Off or switching to another Mode.
4. Check if the file(s) is WMA file(s). The unit does not play WMA format, only MP3 format.
Remote not working
1. Replace battery.
2. Be sure to point the remote towards remote sensor when operating.
3. Remove obstacles in the path of the remote and radio so the remote signal has a straight path to the radio.
Turntable will not work
1. Check it the AC Power source is connected.
2. Press the POWER button /
(on front of unit or on RC) to turn the unit on, the STAND BY INDICATOR light should be off.
3. Check that the unit is in PHONO Mode. Try moving the Tone Arm o the right until a click is heard.
No Sound is coming from the unit
1. The white protective needle cover has not been removed
2. The Volume is not turned up
The Tone Arm will not move
1. The black tie-wrap has not been removed from underneath Tone Arm.
2. Tone Arm hold down clip has not been released.
The unit keeps shutting itself down
1. This unit has a POWER SAVING FEATURE: to comply with new regulations, if the unit is not operated or there is no
signal output for 15 minutes, it will automatically turn itself off.
2. Turn the MAIN POWER switch to OFF and then to ON again to re-activate the unit.
Trademarks – MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and Thomson
AUX IN
R
SP+
L
R
L
INT. EXT.
R
L
to turn the unit on.
on the remote.
11
ANOTHER
AUDIO COMPONENT
AUDIO OUT
L
R
Advertisement
Table of Contents
