Table of Contents
Advertisement
Quick Links
Before starting installation, please read installation guide carefully!
1.
Safety references
1.1
General
This installation instruction contains fundamental references, which are to be considered for
mounting and start-up. It is to be read therefore absolutely before assembly and start-up from the
mechanic as well as the responsible user, too. It should be at the installation site. This installation
guide refers to the tracking system ETATRACK active DIY. There is not only under this section of
"safety references" the specified to consider general safety reference but also into other sections
inserted, special safety reference.
1.2
Reference markings
Attention
Advice
www.lorentz.de
info@lorentz.de
ETATRACK
1000-1500 DIY
Installation guide
Safety references marked with this symbol can cause endangerments of
persons.
Safety references marked with this symbol can cause damages on
machines or its function.
Advices and information to facilitate working and secure perfect operational
sequences.
Release 05.07.19
active
1/13
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Lorentz ETATRACK active 1000
Summary of Contents for Lorentz ETATRACK active 1000
- Page 1 Safety references marked with this symbol can cause endangerments of persons. Safety references marked with this symbol can cause damages on Attention machines or its function. Advices and information to facilitate working and secure perfect operational Advice sequences. www.lorentz.de info@lorentz.de Release 05.07.19 1/13...
-
Page 2: Safe Working
Please follow the instructions to stop the drive in this guide. Inappropriate treatment Working security of tracking systems is only guaranteed in case of normal application. The limit values specified in the technical data are not to be exceeded! www.lorentz.de info@lorentz.de Release 05.07.19 2/13... -
Page 3: Delivery And Storage
-Module fixation clamp(48 pcs) Stainless steel 50x50x1,2mm (12) -Standard parts (1 set) Bolts, washers, nut -Linear motor (1 pc) (13) -Controller fixation (2 pcs) (14) Controller Electronic box incl. Lead Acid Battery and Controller (15) www.lorentz.de info@lorentz.de Release 05.07.19 3/13... -
Page 4: Assembly Preparation
Wooden or metal strip SOUTH (1a) Cross drilling! Fastening clamp During drying-procedure of foundation please use wooden boards to support mounting pole. In case of installation on flat roofs, stability can be effected with clamping belts. www.lorentz.de info@lorentz.de Release 05.07.19 4/13... - Page 5 SOUTH Mounting pole (1a) Fastening clamp Diameter fig. 4.1 Dimensions of surface foundation D =1600mm for ETATRACK 1000 (up to 10 sqm) D = 2200mm for ETATRACK 1500 (up to 15 sqm) www.lorentz.de info@lorentz.de Release 05.07.19 5/13...
- Page 6 SOUTH www.lorentz.de info@lorentz.de Release 05.07.19 6/13...
-
Page 7: Required Tools
2x ring or open ended flat spanner 24mm 2x ring or open ended flat spanner 10 / 13mm Level Rubber or plastic hammer Fastening clamp 2 x 3a 5.2. Hardened foundation: M16 x 190mm www.lorentz.de info@lorentz.de Release 05.07.19 7/13... - Page 8 5.3 Preparing the rails and hinges 1 pc M12 x 95mm Scale 1:1 2 pcs M10 x 80mm Scale 1:1 www.lorentz.de info@lorentz.de Release 05.07.19 8/13...
- Page 9 (See fig. 5.4) Before tightening the screws align module fixation in parallel line Dimension „X“: depends on position of fixation holes in the PV modules. 12pcs X = Distance between holes - 110mm M12 x 140 www.lorentz.de info@lorentz.de Release 05.07.19 9/13...
- Page 10 View from North to South Free leg of angle has to point down on the Eastern side. Fig. 5.4 Arrangement of lower motor fixation www.lorentz.de info@lorentz.de Release 05.07.19 10/13...
- Page 11 - Fixation of solar modules Advice Before final tightening of screws please check easy swivelling feature. In case of difficulties the adjustment of the mounting poles could be not correct. The module frame has to be aligned right-angled. SOUTH www.lorentz.de info@lorentz.de Release 05.07.19 11/13...
- Page 12 The linear motor is in factory setting, which means in morning position. Do not turn the inside bar with the ball! During assembly of the motor on the frame: Dimension (210 mm) must be kept! 210 mm min. 55mm www.lorentz.de info@lorentz.de Release 05.07.19 12/13...
- Page 13 Lower motor fixation with spacer sleeve Upper end of linear motor www.lorentz.de info@lorentz.de Release 05.07.19 13/13...
Need help?
Do you have a question about the ETATRACK active 1000 and is the answer not in the manual?
Questions and answers