Subscribe to Our Youtube Channel
Related Manuals for Hydrofarm ACTIVE AIR ACAN12
Summary of Contents for Hydrofarm ACTIVE AIR ACAN12
- Page 1 INSTRUCTIONS PORTABLE AIR CONDITIONER VENDOR DIRECT WARRANTY. DO NOT RETURN TO RETAILER. SEE WARRANTY INFO ON BACK PAGE. ACAN12...
-
Page 2: Parts List
3. Handle (both sides) 11. Power cord outlet 4. Caster 12. Power cord buckle 5. Upper air filter 13. Power plug socket (behind the grille) 14. Bottom tray drain outlet 6. Upper air intake 15. Vent control 7. Drain outlet FRONT REAR www.Hydrofarm.com... -
Page 3: Operating Conditions
INSTRUCTIONS ELECTRONIC CONTROL OPERATING INSTRUCTIONS Before you begin, thoroughly familiarize yourself with the control panel and remote controller and all its functions, then follow the symbol for the functions you desire. The unit can be controlled by the unit control panel alone or with the remote controller. MODE ROOM TEMPERATURE COOL... -
Page 4: Dry Operation
TIMER OFF indicator light will illuminate. Press the UP or DOWN button to select the desired time. Press the TIMER button again within 5 seconds, and the Auto-on start program will be initiated. The TIMER ON indicator light will also illuminate. Press the UP or DOWN button to select the desired Auto-on start time. www.Hydrofarm.com... -
Page 5: Installation Instructions
INSTRUCTIONS • When the unit is off, press the TIMER button to initiate the Auto-on start program. Pressing it again within five seconds will initiate the Auto-off stop program. • Press or hold the UP or DOWN button to change the Auto time by 0.5 hour increments, up to 10 hours, then at 1 hour increments up to 24 hours. -
Page 6: Tools Needed
Window Slider B 1 pc Foam Seal A (Adhesive) 2 pc Foam Seal B (Adhesive) 2 pc Foam Seal C (Non-adhesive) 1 pc Security Bracket and 2 Screws 1 set 1 pc Drain Hose 1 set Remote Controller and Battery www.Hydrofarm.com... - Page 7 INSTRUCTIONS WINDOW INSTALLATION KIT Step One: Preparing two Exhaust Hose assemblies Press the exhaust hose into the window slider adaptor and unit adaptor, clamp automatically by elastic buckles of the adaptors. 2 Exhaust hose 2 Exhaust hoses assemblies 2 Window slider 2 Unit adaptors adaptors Step Two: Install the two Exhaust hose assemblies to the unit...
-
Page 8: Sliding Window Installation
(Adhesive type) frame to prevent air and insects from getting into the room. Foam seal C (Non-adhesive type) 2. Insert the window slider assembly into the window opening. Window slider B (if required) Window slider A www.Hydrofarm.com... -
Page 9: Vent Control Feature
INSTRUCTIONS 3. Cut the non-adhesive foam seal C strip to VENT CONTROL FEATURE match the window height. Insert the foam The Vent Control is located at the back of the air seal between the glass and the window conditioner. The OPEN position removes stale frame to prevent air and insects from air from the room and exhausts it to the outside. -
Page 10: Care And Maintenance
(take out) children without supervision. • If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. • The appliance shall be installed in www.Hydrofarm.com... -
Page 11: Troubleshooting
INSTRUCTIONS accordance with national wiring regulations. • Do not touch the unit with wet or damp hands or when barefoot. • Do not operate your air conditioner in a wet room such as a bathroom or laundry room. • Do not press the buttons on the control panel with anything other than your fingers. -
Page 12: Function Buttons
If you are sensitive to sleeping hours light when you go to sleep, you can press the LED button to turn off SWING the LED display on the unit. Press the button Starts and stops louver movement again to turn it back on. www.Hydrofarm.com... -
Page 13: Handling The Remote Controller
INSTRUCTIONS HANDLING THE REMOTE CONTROLLER TIPS FOR USING REMOTE CONTROL NOT SURE WHAT A FUNCTION DOES? Refer to • The remote control must be used within 8 the How to Use Basic Functions and How to meters of the unit. Use Advanced Functions sections of this manual •... -
Page 14: Remote Lcd Screen Indicators
1. Press the MODE button to select Auto mode. TIMER Ã Ä 2. Set your desired temperature using the Temp or Temp SWING SLEEP button. 3. Press the ON/OFF button to start the unit. NOTE: FAN SPEED can t be set in Auto mode. www.Hydrofarm.com... -
Page 15: Cool Operation
INSTRUCTIONS COOL OPERATION FAN OPERATION 1. Press the MODE button to select 1. Press the MODE button to select FAN mode. COOL mode. 2. Press FAN button to select the fan speed: 2. Set your desired temperature using the AUTO, LOW, MED or HIGH. Ã... -
Page 16: Timer Off Function
SLEEP SWING the temperature display. NOTE: When setting the TIMER ON or TIMER OFF functions, up to 10 hours, the time will increase in 30 minute increments with each press. After www.Hydrofarm.com... - Page 17 INSTRUCTIONS Your remote display Timer ON Timer is set To turn ON 6 hours from current time Timer OFF Timer is set to turn OFF 8 hours from current time Unit turns Unit turns Timer starts Current time 1PM 6 hours later 8 hours later...
-
Page 18: How To Use The Advanced Functions
(if activated). • If pushing more than 2 seconds, the system will automatically restore the current operation settings including operating mode, setting temperature, fan speed level and sleep feature (if activated). www.Hydrofarm.com... - Page 19 INSTRUCTIONS NOTES: • Buttons design is based on typical model and might be slightly different from the actual one you purchased, the actual shape shall prevail. • All the functions described are accomplished by the unit, if the unit has no this feature, there is no corresponding operation happened when press the relative button on the remote controller.
-
Page 20: Warranty
Disposal of electronic waste in forests and landscapes endangers human and animal health when hazardous substances leak into the ground water and find their way into the food chain. ACAN12 Instructions: revised - January 19, 2017 4:26 PM 20 www.Hydrofarm.com www.Hydrofarm.com...
Need help?
Do you have a question about the ACTIVE AIR ACAN12 and is the answer not in the manual?
Questions and answers