Garudan HVP- 60 SERIES Operation Manual page 30

2.7.2 Parameter in ( Parameter Mode B ] only
~------ .,._ The values are pre-set for H'(P-60-3/4-66
PARAMETER
PARAMETER FUNCTION
RANGE/UNIT DEFAULT
KEY
DESCRIPTION
CODE
(047.MAC) Machine Code ( MAC )
0-82 6 C.D Machine code setting.
(049.SPD) Machine's pulley dimension ( SPD ) 50-200mm 65
B.C.D Setting machine pulley size.
(050.MPD] Motor's pulley dimension ( MPD )
50-150mm 100
B.C.D Setting motor pulley size.
(054.BK)
Motor braked at normal stop (BK )
ON/OFF OFF C.D ON: Motor stop with brake function.
(057.TRU]
The back angle when Motor finish the
ON/OFF OFF C.D
Valid only when the LK mode is selected in the ( 078.TRM )
trimming sequence.(Lockstitch M IC only) ON:When motor finished the trimming cycle, enable the motor backward function.
(058.TR8] Motor returned angles after trimming (TR8 )
o..;255 Degree
40
B.C.D Valid when ( 057.TUR) set ON.
(064.FO)
Full-On time setting for Foot Lifter (FO ) 0-990ms 400 B.C.D Properly set the value to keep good performance of Foot Lifter is essencial.
(065.FC)
Duty-Cycle time setting for Foot Lifter ( FC ) 10-90% 50 C.D
Properly set the value to keep good performance of Foot Lifter is essencial.
(066.FD)
Running-Delay time setting (FD )
0-990ms 120 B.C.D If Foot Lifter is installed, set 120 ms min.
[070.HHC) Cancel Foot Lifting at Half-Heeling pedal (HHC ) ON/OFF OFF
C.D ON: Pedal half heeling without foot lifting function.
N
-
Emergency stop mode for Trimming
Trimmer device protection for Interlock Stitch machine.
[075.SFM) protection (SFM)
N.C./N.O. NC C.D Properly setting the value according to the machine brand and
N.0.=1=Normal Opened.·
model.
N.C.=O=Normal Closed
•Motor running mode at trimming
LK: Trimming from needle down to up.
sequence (TRM)
RK: Turning back to up stop (For Non-UT device Interlock stitch
[078.TRM)
LK,RK,KA,KB KA D machine)
•Motor stops in turning back of
KA: Interlock Stitch machine trimming mode.
CHINA-STITCH M/C
KB: Special Interlock Stitch machine trimming mode.
(082.T1)
Delayed liming prior to trimmer engaged ( T1 ) 0-990ms 100
B.C.D Trimming sequence setting.
[083.T2]
Extended timing of trimming beyong up-stop ( T2) 0-990ms 200
[086.L 1)
Delayed timing prior to tension release engaged (L 1) 0-990ms 340 B.C.D
Tension release sequence setting.
[087.L2]
Extened timing of tension release beyong up-stop (L2)
0-1500ms
80 A.B.C.D
(092.W1)
Delayed timing prior to wiper engaged (W1 ) 0-980ms 340 B.C.D Time setting between needle up to wiper active.
(093.W2) Setting timing of wiping ( W2 ) 0-9990ms 80
A.B.C.D Wiper sequence.
(094.WFJ
Delayed timing prior to Foot Lifter engaged (WF) 0-990ms 50 B.C.D Time setting between wiper active to presser foot active.
( 114.UEG) Stop angles in pulse from edge to up-stop (UEG ) 5-250 Pules 40 B.C.D Fine adjust the needle stops at up position. (40 is the central value)
[ 116.DRU] Reverse angles through Needle down( DRU ) 0-255 Degrees 180
B.C.D Valid only when the RK mode is selected in the Parameter Code ( 078.TRM J
(121.ANU) Needle goes up as power turned on ( ANU ) ON/OFF ON
C.D ON: Power turned on, needle goes up automatically.
( 122. HL] Maximum sewing speed limiter (HL ) 150-8000spm 4500 A.B.C.D The avail.able high speed will be limited by this parameter value.
'
ENGUSH
'
'
~