Table of Contents
Advertisement
©
DIRECT
button/indicator
Use
this
button
when
you do
not
wish
to
pass the output from
input
terminal
equipment through
the various
frequency
adjust-
ing circuits
(BASS,
TREBLE,
BALANCE, LOUDNESS).
On
:
The
indicator
lights.
The
signals input
through
the
input
terminals are
reproduced without passing through
the
various
frequency
adjusting
circuits.
This
results
in
flat,
pure
sound which
is
a
more
faithful
reproduction
of
the
input source.
Off
:
The
indicator
goes
out.
The
signal
passes through
the
various
frequency
adjusting
circuits.
©
REC SELECTOR
switch
(For
TAPE 1/DAT
terminals)
When
this
switch
is
set to a position
other than
SOURCE
or OFF,
the
equipment
selected
by
the
REC SELECTOR
switch
can
be
recorded, irrespective of
the
INPUT
SELECTOR
knob and
the
DIRECT
button
settings
(TAPE 1/DAT
terminals).
SOURCE
:
To
record
from
the
equipment
selected
by
the
INPUT
SELECTOR
knob.
OFF
:
In
this
position,
nothing
from
the
REC
terminals
of
TAPE
1/DAT
is
output.
Set
to
this
position
when
not
recording; the cassette
deck
will
be
disconnected, im-
proving
sound
quality.
CD
:
To
record
from
the
equipment connected
to the
CD
terminals.
TUNER
:
To
record
from
the
equipment connected
to the
TUNER
terminals.
NOTE:
The
function selected
using
the
INPUT SELECTOR
knob
will
be
recorded
irrespective
of the
position
of the
REC SELECTOR
switch
(TAPE
2
MONITOR
terminals).
®
BALANCE
control
Should normally be
left
in
the center
position.
Adjust the
bal-
ance
if
the
sound
is
louder
from one
of
the speakers.
If
the
right
side
is
louder, turn
toward
the
L
(left)
position
and
if
the
left
side
is
louder, turn
toward
the
R
(right)
position.
NOTE:
This control
does
not operate
when
the
DIRECT
button
is
in
the
on
position.
©
MUTtNG
button/indicator
(A-605R
and A-505R
only)
Use
to
temporarily lower
sound
volume.
On
:
The
VOLUME
indicator flashes.
The sound volume
is
lowered
to
one-tenth
(-20dB).
Off
:
The
VOLUME
indicator
lights.
The sound
will
return
to
Its
previous
volume.
®
LOUDNESS
button/indicator
Use
when
listening at
low
volume
level.
On
:
The
indicator
lights.
Boosts low
and
high frequencies
to
give
added punch
to
playback
even
at
low
volume
level.
Off
:
The
indicator
goes
out.
Should normally be
left in
this
position.
NOTE:
This
button
does
not operate
when
the
DIRECT
button
is
in
the
on
position.
®
TREBLE
tone
control
Use
to adjust the
high-frequency
tone.
The
center
position
is
the
flat
(normal)
position.
When
turned
to
the
right,
the high-frequency
tone
is
emphasized;
when
turned
to
the
left,
the high-frequency
tone
is
de-emphasized.
NOTE:
This control
does
not operate
when
the
DIRECT
button
is
in
the
on
position.
®
BASS
tone
control
Use
to
adjust the
low-frequency
tone.
The
center
position
is
the
fiat
(normal)
position.
When
turned
to
the
right,
the low-frequency
tone
is
emphasized;
when
turned
to
the
left,
the low-frequency
tone
is
de-emphasized.
NOTE:
This control
does
not operate
when
the
DIRECT
button
is
in
the
on
position.
@
SPEAKERS
B
selector button/indicator
Use
this
button
to
listen
to
the
speaker
system connected
to
the
SPEAKERS
B
terminals.
On
:
The
indicator
lights.
Sound
is
heard from
the
speaker
system.
Off
:
The
indicator
goes
out.
No
sound
is
heard from the
speaker system.
Set
to
this
position
when
listening
with
headphones.
®
PHONES
jack
When
using
headphones,
insert
the plug
into this
jack.
®
SPEAKERS
A
selector button/indicator
Use
this
button
to
listen
to
the speaker
system connected
to
the
SPEAKERS
A
terminals.
On
:
The
indicator
lights.
Sound
is
heard from
the
speaker
system.
Off
:
The
indicator
goes
out.
No
sound
is
heard from the
speaker system.
Set
to
this
position
when
listening
with
headphones.
33
Hide quick links:
Advertisement
Table of Contents
