Table of Contents
Advertisement
Quick Links
J643 SBC-GX1
Product Information
Full information about other Arcom products is available by contacting our Website at:
www.arcomcontrols.com
Useful Contact Information
Customer Support Europe
Tel:
+44 (0)1223 412 428
Fax:
+44 (0)1223 403 409
E-mail: support@arcom.co.uk
Sales offices
United Kingdom:
Arcom Control Systems Ltd
Clifton Road
Cambridge CB1 7EA, UK
Tel: 01223 411 200
Fax: 01223 410 457
E-mail:
sales@arcom.co.uk
Whilst Arcom's sales team is always available to assist you in making your decision, the final
choice of boards or systems is solely and wholly the responsibility of the buyer. Arcom's entire
liability in respect of the boards or systems is as set out in Arcom's standard terms and
conditions of sale.
If you intend to write your own low level software, you can start with the source code on the
disk, which is supplied. This is example code only to illustrate use on Arcom's products. It has
not been commercially tested. No warranty is made in respect of this code and Arcom shall
incur no liability whatsoever or howsoever arising from any use made of the code.
© 2000 Arcom Control Systems Ltd
Arcom Control Systems is a subsidiary of Fairey Group Plc.
All trademarks recognised.
C O N T R OL S Y S T E M S
SBC-GX1
Technical Manual
United States:
Arcom Control Systems Inc
13510 South Oak Street
Kansas City MO 64145 USA
Tel: 816 941 7025
Fax: 816 941 7807
E-mail:
icpsales@arcomcontrols.com
Customer Support US
Tel:
816 941 7025
Fax:
816 941 7807
E-mail: support@arcomcontrols.com
Sales hotlines
Belgium:
Germany:
Groen Nummer:
Kostenlose Infoline:
Tel: 0800 7 3192
Tel: 08001 824 511
Fax: 0800 7 3191
Fax:08001 824 512
France:
Netherlands:
Numero Vert
Gratis Nummer:
Tel: 0800 90 84 06
Tel: 0800 0221136
Fax: 0800 90 84 12
Fax: 0800 0221148
2192-10757-000-000
Italy:
Numero Verde:
Tel: 0800 790841
Fax: 0800 780841
Arcom Control Systems Ltd
operate a company-wide quality
management system which has
been certified by the British
Standards Institution (BSI) as
compliant with ISO9001:1994
Page 0
Advertisement
Table of Contents
Related Manuals for Arcom SBC-GX1
Summary of Contents for Arcom SBC-GX1
-
Page 1: Product Information
Whilst Arcom’s sales team is always available to assist you in making your decision, the final choice of boards or systems is solely and wholly the responsibility of the buyer. Arcom’s entire liability in respect of the boards or systems is as set out in Arcom’s standard terms and conditions of sale. -
Page 2: Table Of Contents
Acknowledgements ........................ 4 Technical Support........................5 Introduction ..........................6 Features ..........................6 Getting Started ......................... 8 Using the SBC-GX1........................8 CPU Configuration........................8 Installing Memory ........................8 Connecting a Floppy disk drive....................9 Connecting a Hard disk drive....................9 Connecting a CD-ROM (IDE Type)..................9 Using the Compact Flash Socket.................... - Page 3 J643 SBC-GX1 2192-10757-000-000 Bootdisk ..........................34 Operating System Drivers ..................... 34 Windows 95 Driver Support ....................34 Windows 98 Driver Support ....................36 Windows NT4.0 Driver Support .................... 38 Other Software Support ......................40 Hardware Support Information....................40 Detailed Hardware Description ..................... 41 Processor ..........................
-
Page 4: Revision History
J643 SBC-GX1 2192-10757-000-000 PL15 -VGA CRT connector ....................61 PL16 - Printer Port (LTP1)....................61 PL17 - Floppy Disk Interface ..................... 62 PL18 – COM2 RS232 Serial Port ..................62 PL19 – COM1 RS232 Serial Port ..................62 PL20 & PL23 - PC/104 Connector..................63 PL21 –... -
Page 5: Disclaimer
When disposing of the board or battery, take appropriate care. Do not incinerate, crush or otherwise damage the battery. Packaging Please ensure that should a board need to be returned to Arcom Control Systems, it is adequately packed, preferably in the original packing material. Electromagnetic Compatibility (EMC) -
Page 6: Technical Support
J643 SBC-GX1 2192-10757-000-000 Technical Support Arcom Control systems has a team of technical support engineers who will be able to provide assistance if you have any problems with this product. Please contact the support team at support@arcom.co.uk (support@arcomcontrols.com Page 5... -
Page 7: Introduction
It has been designed to be used as a reference and user manual and includes information on using all aspects of the board. This manual should have been supplied as part of an SBC-GX1 development kit and you should have already read the ‘Quickstart’ manual supplied. - Page 8 J643 SBC-GX1 2192-10757-000-000 Ö Bus Mastering mode, up to two devices Ö Supports PIO Mode 4 or Ultra DMA/33 Hard Disk and ATAPI CD-ROM • FDD Interface Ö Supports two floppy drives 360KB, 720KB, 1.2MB, 1.44MB, 2.88MB • Parallel Port Ö...
-
Page 9: Getting Started
The section below has been designed to provide guide you through setting up and using some of the features of the SBC-GX1. If you would like more detailed information on any aspect of the board refer to the “Detailed Hardware Description” section of this manual. -
Page 10: Connecting A Floppy Disk Drive
Connecting a Hard disk drive Up to two IDE hard disk drives can be supported by the SBC-GX1 board. Both drives should be connected to PL2 via a 40 way 1:1 ribbon cable. The primary drive should be set-up as a ‘MASTER’... -
Page 11: Connecting A Mouse
DOS. Windows 95/98/2000/NT will provide mouse support via built in drivers. Using the Serial interfaces (RS232) The four serial port interfaces on the SBC-GX1 are fully PC compatible. They are decoded at standard PC address locations for COM1, COM2, COM3 and COM4. PC applications will be able to use these ports without any special configuration. -
Page 12: Using The Audio Features
No Connect Using the Audio features There are three Audio interfaces supported on the SBC-GX1 Line In, Line Out and Microphone. The Line In and Line Out interfaces support stereo signals and the Microphone provides a MONO input. Connections are routed to a 10 way boxed header PL24, the relevant signals for... -
Page 13: Using The Flat Panel Interface
PC/104 specification. In order to use a PC/104 board with the SBC-GX1 it should be plugged into PL20 for 8-bit cards and PL20/PL23 for 16-bit cards. Before powering up the system ensure that you have checked that the link settings on the card for I/O address, IRQ and DMA settings do not conflict with any devices on the SBC-GX1. -
Page 14: Using The Usb Ports
J643 SBC-GX1 2192-10757-000-000 If you are using a PC/104 card that requires +5V, this will automatically be supplied via the PC/104 header. If you require +12V this will only be available if the +12V pin on the ‘POWER’ connector PL12 has been connected to a supply. If you require –12V or –5V these will need to be supplied directly to the PC/104 board. -
Page 15: Links And Connectors
J643 SBC-GX1 2192-10757-000-000 Links and Connectors There are twelve user selectable links on the SBC-GX1. The following section provides details on these links. The ‘+’ sign indicates the default position for each link. Page 14 C O N T R OL S Y S T E M S... -
Page 16: Lk1 - Watchdog Timer Timeout Selection
J643 SBC-GX1 2192-10757-000-000 LK1 – Watchdog Timer timeout selection The watchdog timer has two pre-configured timeout delays, these are either 2 or 8 seconds. This link can be used to select between the timeout periods. Description 2 second timeout Omit+ 8 second timeout LK2 –... -
Page 17: Lk6 - Com3 Irq Routing
J643 SBC-GX1 2192-10757-000-000 LK6 – COM3 IRQ routing This link is used to select which IRQ signal is connected to the COM3 serial port. Description IRQ4 IRQ11 LK7 – Clear CMOS/ Battery Disable A battery link is fitted that is used to prevent drain on the battery during shipment. This link can also be used to clear the contents of the CMOS RAM. -
Page 18: Lk11 & Lk12 - User Links
2192-10757-000-000 LK11 & LK12 – User Links These two links are user configuration links. They have no function on the SBC-GX1, but can be used by an application program to signify a configuration setting. The position of these links can be read via the special function I/O register at address 259H (See User links section for details). -
Page 19: Award Bios Setup
J643 SBC-GX1 2192-10757-000-000 AWARD BIOS SETUP The Award BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-packed RAM so that it retains the setup information when the power is turned off. -
Page 20: The Main Menu
J643 SBC-GX1 2192-10757-000-000 MAIN MENU The on-line description of the highlighted setup function is displayed at the bottom of the screen. Status Page Setup Menu/Option Page Setup Menu Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. - Page 21 J643 SBC-GX1 2192-10757-000-000 LOAD SETUP DEFAULTS Chipset defaults indicates the values required by the system for the maximum performance. INTEGRATED PERIPHERALS This section includes all the items of IDE hard drive and Programmed Input / Output features. PASSWORD SETTINGS Change, set, or disable password. It allows you to limit access to the system and setup, or just to setup.
-
Page 22: Standard Cmos Setup
J643 SBC-GX1 2192-10757-000-000 STANDARD CMOS SETUP The items in the Standard CMOS Setup Menu are divided into several categories. Each category includes one or more than one setup item. Use the arrow keys to highlight the item then use the <PgUp> or <PgDn> keys to select the value you want in each item. -
Page 23: Bios Features Setup
J643 SBC-GX1 2192-10757-000-000 BIOS Features Setup ROM PCI/ISA BIOS (2A434001) BIOS FEATURE SETUP AWARD SOFTWARE, INC CPU Internal Cache : Enabled Video BIOS Shadow : Enabled C8000-CBFFF Shadow : Disabled Quick Power On Self Test : Enabled CC000-CFFFF Shadow :... - Page 24 J643 SBC-GX1 2192-10757-000-000 Enabled Activate automatically when the system boots up causing a warning message to appear when anything attempts to access the boot sector or hard disk partition table. Disabled No warning message to appear when anything attempt to access the boot sector or hard disk partition table.
- Page 25 J643 SBC-GX1 2192-10757-000-000 Boot Up Floppy Seek During POST, BIOS will determine if the Floppy disk drive installed is 40 or 80 tracks. 360K type is 40 tracks while 720K , 1.2M and 1.4M drive type as they are all 80 tracks.
- Page 26 J643 SBC-GX1 2192-10757-000-000 Video BIOS Shadow It determines whether video BIOS will be copied to RAM, however, it is optional from chipset design. Video shadow will increase the video speed. Enabled: Video shadow is enabled Disabled: Video shadow is disabled C8000-CBFFF Shadow/DC000-DFFFF Shadow These categories determine whether optional ROM will be copied to RAM in 16K byte.
-
Page 27: Chipset Features Setup
J643 SBC-GX1 2192-10757-000-000 Chipset Features Setup ROM PCI/ISA BIOS (2A434001) CHIPSET FEATURE SETUP AWARD SOFTWARE, INC CPU Warning Temperature : 100 C/212 SDRAM CAS Latency Time : AUTO SDRAM Clock Ratio Div By : C/122 Current CPU Temperature 16-bit I/O Recovery (CLK) :... - Page 28 J643 SBC-GX1 2192-10757-000-000 CPU Warning Temperature This setting is used to set the trip level on the LM84 remote temperature sensor. This sensor is used to monitor the CPU die temperature. Once the threshold is reached the LM84 output will be driven low.
-
Page 29: Power Management
J643 SBC-GX1 2192-10757-000-000 Power Management ROM PCI/ISA BIOS (2A434001) POWER MANAGEMENT SETUP AWARD SOFTWARE, INC. Power Management : Disabled IRQ1 (Keyboard) : IRQ3 (COM2) : **PM Timers** IRQ4 (COM1) : Doze Mode : Disabled IRQ5 (LPT2) : Standby Mode :... - Page 30 J643 SBC-GX1 2192-10757-000-000 Item Options Descriptions A. Power Management 1. Disable Global Power Management will be disabled 2. User Define Users can configure their own power management 3. Min Saving Pre-defined timer values are used such that all timers are in their MAX value 4.
-
Page 31: Pnp / Pci Configuration Setup
J643 SBC-GX1 2192-10757-000-000 PNP / PCI Configuration Setup ROM PCI / ISA BIOS (2A434001) PNP / PCI CONFIGURATION AWARD SOFTWARE, INC. PNP OS Installed : PCI IRQ Activated By: Level Resources Controlled By : Manual Used MEM base addr: Reset Configuration Data :... -
Page 32: Integrated Peripherals
J643 SBC-GX1 2192-10757-000-000 INTEGRATED PERIPHERALS ROM PC/ISA BIOS (2A434001) INTEGRATED PERIPHERALS AWARD SOFTWARE, INC. IDE HDD Block Mode : Enabled ECP mode User DMA : Primary IDE Channel : Enabled Build in CPU Audio : Enabled Master Drive PIO Mode :... -
Page 33: Load Bios Default
J643 SBC-GX1 2192-10757-000-000 Load BIOS Default Load BIOS Default (Y/N) ?N When you access "Load BIOS Default", the following message appears: The BIOS Default values are the "worst case" default, and are the most stable values for the system. Use them if the system is performing erratically due to hardware problems. To load the BIOS Default values, press <Y>... -
Page 34: Software Support
CD. Datalight ROM-DOS 6.22 If your SBC-GX1 board is fitted with flash memory it will be supplied with a license for Datalight's ROM-DOS 6.22 operating system. This operating system will be pre-installed on the flash drive. -
Page 35: Bootdisk
J643 SBC-GX1 2192-10757-000-000 automatically load the file and prompt you to confirm that you want to reprogram the BIOS ROM. Once the device has been reprogrammed you should press F1 to reboot the system. Note:- During this process it is important that you do not switch off the board as this may cause the BIOS ROM to be corrupted and this will stop the board from operating. - Page 36 J643 SBC-GX1 2192-10757-000-000 14. Look under System - Device Manager -Display Adapter and verify “National Semiconductor XpressGRAPHICS”. If it’s not present repeat the procedure. National XpressAUDIO Audio Driver 1. Go to control panel and Select System – Device Manager 2. Choose “Other Devices” from the list and Select “PCI Multimedia Audio Device”...
-
Page 37: Windows 98 Driver Support
J643 SBC-GX1 2192-10757-000-000 8. Wait while the drivers installs and select finish 9. You will be on Control Panel 10. Select System – Device manager 11. Select “ Hard Disk Controller” 12. Select “Standard Dual IDE Controller” and select Remove 13. - Page 38 J643 SBC-GX1 2192-10757-000-000 National XpressGraphics Video Driver 1. Go to control panel , Select System – Device Manager 2. Choose “Display Adapters” from the list 3. Select “Standard PCI VGA adapter” and select ”Properties” 4. Select the “Driver” tab and select “Update driver”.
-
Page 39: Windows Nt4.0 Driver Support
J643 SBC-GX1 2192-10757-000-000 National UDMA Driver 1. Go to Control Pane and Select “Add New Hardware” 2. Select “no” and select “next” then select “Hard disk Controller” 3. Select “Have disk” 4. Select D:\Win98\UDMA\CX5530.INF 5. From the “Install from disk” window, click OK 6. - Page 40 J643 SBC-GX1 2192-10757-000-000 Install NT 4.0 on an NTFS partition. When prompted ,select ‘Do not connect this computer to a network at this time’ and leave the video controller configured as standard VGA. If you would like to install Windows NT 4.0 Service pack 6a. Select the following file form the support CD- ROM once NT 4.0 has completed installation.
-
Page 41: Other Software Support
Please refer to the documentation on the CD-ROM for the latest information. Hardware Support Information As the SBC-GX1 is a fully compatible PC/AT processor board any standard PC reference guide will provide information on hardware aspects of the board. The following material has been included on the support CD-ROM as it relates to specific features of the board which may not be available from other sources. -
Page 42: Detailed Hardware Description
. The GX1 is a 64-bit x86 compatible device and has 16K L1 write-back cache integrated into the processor. The device also contains an integrated floating point unit. A 300MHz part is used on the SBC-GX1, this part is supplied with a 33MHz clock signal and multiplied within the device. -
Page 43: Bios Eprom
Flash Memory/Silicon Disk The SBC-GX1 board supports up to 16MB flash memory. This memory is configured to be a read/write silicon disk drive. The Datalight FlashFX flash filling system will automatically be loaded during the POST routine to enable the flash drive to be accessed. The flash drive uses a 16K memory window at 000DC000-000DFFFF to access the devices and two I/O address locations are used to select the appropriate flash area. -
Page 44: Static Ram
Register 1 Bit 7 is 0, i.e. Flash is disabled and write protected. Static RAM The SBC-GX1 is designed to support a 128K byte static RAM device. This device is decoded using the same memory window as the Flash disk. Selection between Flash and SRAM is achieved by setting bit 6 in I/O register 259H. -
Page 45: Memory Map
64K I/O address range of the processor. The following table shows the I/O address mapping for the SBC-GX1. If expansion boards are added via the PC/104 interface you should ensure that they are configured to be at a free address location. -
Page 46: Graphics Controller
J643 SBC-GX1 2192-10757-000-000 Graphics Controller The National GX1 processor contains a high performance graphics controller and with the support of the CS5530 this can be used to drive TFT LCD flat panel and CRT displays simultaneously. The graphics controller is supported by a fully PC compatible video BIOS which enables it to support all standard VGA and XGA graphics modes. -
Page 47: Interrupt Assignments
VGA compatible CRT monitor. A suitable cable is provided as part of the SBC-GX1 development kit. The following table shows the connection details for this cable. The CRT signals may be affected by noise and therefore this cable should be keep as short as possible and should be routed away from other signals to stop any crosstalk. -
Page 48: Dma Controller
DMA Controller There are two 8237 DMA controllers on the SBC-GX1. These controllers are cascaded in a standard PC/AT style. DMA channels 0-3 are used to support 8-bit devices and DMA channels 4-7 support 16-bit devices. -
Page 49: Ide Interface
The secondary controller is used to support a compact flash card interface. The compact flash socket PL25 is mounted on the underside of the SBC-GX1, This socket can be used to support both Type I and Type II compact flash cards. The compact flash card can be used to replace a mechanical drive in the system. -
Page 50: Real Time Clock
J643 SBC-GX1 2192-10757-000-000 up it will be used as the default boot device. If no drive is present the BIOS will continue to operate correctly. The floppy disk drive cable should have three connectors, two which are connected directly 1:1 and one which has pins 10-16 twisted. -
Page 51: Ethernet Controller
ETHERNET directory. 16-Bit SoundBlaster The Audio support provided on the SBC-GX1 is fully compatible with the 16-bit SoundBlaster interface. This device provides support for stereo Line IN and Line OUT and mono Microphone input. The SoundBlaster is supported via the National ‘XpressAUDIO’ software which is built into the BIOS code. -
Page 52: Watchdog Timer
User Links There are two user links on the SBC-GX1 LK11 and LK12. The status of these user links can be read via I/O address 259H bits 1 and 2. If the link is made then the corresponding bit will be read as a logic ‘0’... -
Page 53: General Purpose I/O
General Purpose I/O Eight general purpose I/O lines are provided on the SBC-GX1. These lines are routed to a 20 way 0.1” header PL13. The header provides un-buffered and buffered versions of the lines. The buffered version can be used to drive higher output current up to 24mA per output than the un- buffered version. -
Page 54: Cpu Temperature Sensor
Serial Ports There are four high speed 16550 serial UART’s on the SBC-GX1. All four channels are fully software compatible with the 16550 and can be used as standard RS232 serial interfaces. The table below shows the configuration for each channel. -
Page 55: Rs422/485 Interfaces
‘1’ the driver is switched off and data can be received from other devices. When the RTS line is at logic ‘0’ the driver is on. Any data which is transmitted from the SBC-GX1 will be automatically echoed back to the receiver. This enables the serial communications software to detect that all data has been sent and disable the driver when required. -
Page 56: Parallel Port
The parallel port can be used to connect an external printer, tape drive, disk drive, scanner etc. Power Supply The SBC-GX1 is designed to operate from a single +5V ± 5% (4.75V to +5.25V) supply. The power connector PL12 has two +5V connection and three ground connections. These connections are connected on board. -
Page 57: Status Led's
J643 SBC-GX1 2192-10757-000-000 I/O 260H Write Description Operation Shutdown COM1 0 = Enabled (Default) Shutdown COM2 1 = Disabled Shutdown COM3 Shutdown COM4 No Function No Function No Function No Function Status LED’s There are three status LED’s on-board Colour... -
Page 58: Appendix A - Connector Details
J643 SBC-GX1 2192-10757-000-000 Appendix A – Connector details PL1 - Auxiliary Header 6 way 0.1” dual row pin header Signal Name Signal Name Speaker Negative Speaker Positive Reset Input Ground Suspend/Resume Ground PL2 - IDE Disk Interface 40 way 0.1” boxed pin header... -
Page 59: Pl5 - Ethernet Rj45
J643 SBC-GX1 2192-10757-000-000 PL4 - PCI Connector 32-bit card edge connector Side B Side A Side B Side A -12V /TRST AD17 AD16 +12V /CBE2 +3.3V /FRAME /IRDY +3.3V /TRDY /INTC /DEVSEL /INTD /INTA /STOP /INTB /LOCK +3.3V /PRSNT1 RSVD... -
Page 60: Pl6 - Com3 Rs232 Serial Port
J643 SBC-GX1 2192-10757-000-000 PL6 – COM3 RS232 Serial Port 10 pin 0.1” boxed pin header. Signal Name Signal Name No Connect PL7- PS/2 Keyboard 6-pin Mini-DIN Signal Name KB DATA No Connect Ground KB CLOCK No Connect PL8 - USB Ports 10 way 0.1”... -
Page 61: Pl11 - Flat Panel Interface Connector
J643 SBC-GX1 2192-10757-000-000 PL11 - Flat Panel Interface Connector 34 way 0.1” boxed header Signal Name Signal Name FPD0 FPD1 FPD2 FPD3 Ground FPD4 FPD5 FPD6 FPD7 Ground FPD8 FPD9 FPD10 FPD11 Ground FPD12 FPD13 FPD14 FPD15 Ground FPD16 FPD17... -
Page 62: Pl14 - Com4 Rs485/422 Serial Port
J643 SBC-GX1 2192-10757-000-000 PL14 – COM4 RS485/422 Serial Port 10 pin 0.1” boxed pin header Signal Name Signal Name No Connect No Connect Ground Ground TXB/(RXB 485) TXA/(RXA 485) Ground No Connect PL15 -VGA CRT connector 16 way 0.1” boxed pin header... -
Page 63: Pl17 - Floppy Disk Interface
J643 SBC-GX1 2192-10757-000-000 PL17 - Floppy Disk Interface 34 way 0.1” boxed pin header Signal Name Signal Name Ground DENSEL Ground DRATE Ground /INDEX Ground /MTR0 Ground /DRV1 Ground /DRV0 Ground /MTR1 Ground Ground /STEP Ground /WDATA Ground /WGATE Ground... -
Page 64: Pl20 & Pl23 - Pc/104 Connector
J643 SBC-GX1 2192-10757-000-000 PL20 & PL23 - PC/104 Connector Row A & B - 64 way 0.1” Non-Stackthrough PC/104 compatible connector Row C & D - 40 way 0.1” Non-Stackthrough PC/104 compatible connector Row A Row B Row C Row D... -
Page 65: Pl22 - In-System-Programming Header
J643 SBC-GX1 2192-10757-000-000 PL22 – In-System-Programming header This connector is used at assembly time only. PL24 - 16-bit SoundBlaster 10 way 0.1” pin header Signal Name Signal Name Ground MIC IN Ground LEFT IN Ground RIGHT IN Ground LEFT OUT... -
Page 66: Appendix B - Specification
J643 SBC-GX1 2192-10757-000-000 Appendix B – Specification National Semiconductors Geode™ GX1 MMX-enhanced processor Memory 16MB, 32MB, 64MB, 128MB, 256MB 3.3V un-buffered SDRAM 144-pin SODIMM Module. 4M, 8M, 16M Intel Strata Flash 256K Flash BIOS EPROM VGA Video National Semiconductors ‘XpressGraphics’ VGA controller... -
Page 67: Appendix C - Mechanical Diagram
J643 SBC-GX1 2192-10757-000-000 Appendix C - Mechanical Diagram SBC-GX1 0 .0 0 0 .0 0 5 .0 8 5 .0 8 6 .3 5 1 4.6 0 1 7 .14 7 2 .39 7 3 .6 6 7 6 .2 0 8 2 .6 8... -
Page 68: Appendix D - Tft Display Interface Cable
J643 SBC-GX1 2192-10757-000-000 Appendix D – TFT Display Interface cable The following table shows the connection details for the NEC 6.5” LCD flat panel display NL6448BC20-08 used in the development kits: SBC-GX1 PL15 DF9M-31 D-Type Panel Signal Name +5V Power... -
Page 69: Appendix E - Reference Information
J643 SBC-GX1 2192-10757-000-000 Appendix E - Reference Information Product information, product notices, updated drivers and support material. 24hr-Online ordering System www.arcomcontrols.com PC/104 Consortium PC/104 and PC/104-Plus Specifications. Vendor information and available add on products. www.pc104.org PCI Special Interest Group PCI Bus specification and list of manufacturers. -
Page 70: Appendix F - Troubleshooting
2192-10757-000-000 Appendix F – Troubleshooting The SBC-GX1 board is delivered 'Ready to Run' and will automatically start running and load an operating system when power is applied. Either from the on board flash memory, compact flash or mechanical disk drive. Once the board is running the information in this manual will provide you with guidelines and connection details for attaching peripherals and using the board.
Need help?
Do you have a question about the SBC-GX1 and is the answer not in the manual?
Questions and answers