Advertisement

Quick Links

Owner's guide
How to use your new Opalum sound system

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Actiline and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Opalum Actiline

  • Page 1 Owner’s guide How to use your new Opalum sound system...
  • Page 2: Table Of Contents

    7.4 IR learning 7.3 Source select (learned IR remote only) 7.5 Power on/off (learned IR remote only) 7.6 Volume control (learned IR remote only) 7.7 Factory reset The Opalum sound system for integrators 8.1 RS232 control Owner’s guide Rev. 2.3...
  • Page 3: The Control Hub

    Actisonic® technology. This output will sense if a subwoofer is attached and automatically match the sub-woofer and Opalum speakers using a high precision digital crossover at 80 Hz and 24 dB/octave. If the subwoofer has its own adjustable low-pass filter it should be set to the highest possible frequency in order not to interfere with the digital crossover of the Opalum Control Hub.
  • Page 4: The Status Indicator

    The status indicator The LED on the front of the control hub indicates the current system status. Its color indicates the current input source and its intensity the system status. The indicator color matches the color marking of the corresponding input on the back of the Control Hub. Since all inputs are normally mixed, the most common color will be white indicating that the product is in Mixer mode.
  • Page 5: Short Circuit Protection

    Short circuit protection To protect from shorted or faulty wired speaker cables the system is equipped with Actiline® short circuit protection. If a problem is detected, the power to the speakers is automatically turned off and the status indicator starts flashing red. To recover from short circuit mode you may...
  • Page 6: Connecting The System

    Connecting the system The speakers of the Opalum sound system can be connected to the Control Hub in two different ways thanks to the Actiline® technology. In both cases use the included speaker cables or other two conductors stranded 18 gauge (0.75 mm ) or higher/thicker cable.
  • Page 7: Using The Speaker Terminals

    Using the speaker terminals In the Opalum product range there are two types of speaker terminals present: • Push type terminals • Screw type terminals Push terminal Screw terminal 5.1 Installing speaker cable in push type terminals 1. Push terminal firmly until cable hole is fully open.
  • Page 8: Mounting The Speakers

    Mounting the speakers 6.1 Wall mounting the speakers Both the Opalum FLOW, BREEZE and STREAM series speakers are wall-mountable. (STREAM series speakers can also be standing tabletop). For optimum sound performance we recommend to mount the speaker at such height that the middle of the speaker is at about the height of the listener's ears.
  • Page 9: Using The Opalum Sound System

    To connect your mobile device or PC to the Opalum sound system using Bluetooth you first need to pair the devices. Please see the user guide of your device for how to pair. The Opalum sound system is identified by the name “Opalum xxxxxx”, where xxxxxx is a unique number. During the pairing process you will be requested to enter a PASS code.
  • Page 10: Source Select (Learned Ir Remote Only)

    (Yellow) (Pink) 7.5 Power on/off (learned IR remote only) Using the learned IR buttons; the Opalum sound system can be switched ON and OFF. If the system is manually switched OFF, the automatic wakeup is disabled. Owner’s guide Rev. 2.3...
  • Page 11: Volume Control (Learned Ir Remote Only)

    7.6 Volume control (learned IR remote only) Using the learned IR buttons; the volume can be adjusted. When the system goes OFF or into standby, the latest volume setting is stored and will be set when the system is switched ON again. 7.7 Factory reset The factory reset function is to bring the unit back to the initial settings set by the factory.
  • Page 12: The Opalum Sound System For Integrators

    The Opalum sound system for integrators 8.1 RS232 control The RS232 control enables system integrators to control the product by sending commands. 8.1.1 RS232 pin connection The RS232 is located on the rear. See drawing in the very beginning of this guide, it’s the input/output marked IR/RS232 shown as socket 5 in the picture.
  • Page 13 8.1.3 RS232 commands table Function Command In hex Description Power ON pwr1 70 77 72 31 0D Turns on the hub Power OFF pwr0 70 77 72 30 0D Turns off the hub Power Toggle pwrt 70 77 72 74 0D Toggles the power of the off.

Table of Contents