For Legacy CDMA Carriers For Legacy GSM Carriers Dual-SIM Operation User Interface Control Default Switch Operation (dual SIM) WIRELESS NETWORK ACTIVATION – Z4200 3G (CDMA/EVDO/1XRTT) AT Commands OTAP/OMA Activation WIRELESS NETWORK ACTIVATION – Z4400 3G (GSM/UMTS/HSPA) SECURITY Change the Default User ID and Password...
Page 3
10 October 2016 SMS Management White List Status (SMS) SSH Access Web Administration Additional Security Features Authlogread Intrusion Detection DEVICE PROFILE Device Network Profile Gateway Client Application Parameters Location Application Alarming Application Logging Email Configuration Automation Display Groups Dashboard Options LOCAL INTERFACES Overview RS232/RS485 Ports...
Page 4
10 October 2016 10.1 Time Source Cellular Network Network Time Protocol (NTP) Server 10.2 Location Source SKYCLOUD SERVICES TOOLS 12.1 Flash Update Client 12.2 Backup and Restore APPLICATIONS...
1 Introduction Welcome to the Ctek SkyRouter User’s Guide. While the primary focus of this manual is the Z4550 4G/LTE model it also documents variations in the user interface caused by different network technologies, CDMA for the Z4200 and HSPA for the Z4400.
10 October 2016 Setting or Parameter Factory Default Firewall Status Enabled – See security section below WAN Ping Response Disabled – See security section below NAT Traffic to WAN Enabled – See security section below XML Interface Disabled – See security section below IP White List Disabled –...
Page 7
10 October 2016 Figure 2 The Quick Panel display presents an overview of the network and equipment status, and provides navigation to the Administrative functions. The Quick Panel status information is a snapshot in time and must be refreshed to observe changes in dynamic parameters such as network connections or signal strength.
3 Wireless Network Activation – Z4550 4G/LTE Ctek’s Z4550 SkyRouter operates on North American LTE networks on bands 2, 4, 5, 13, 17, and 25 with fallback to the appropriate 3G network for the selected carrier. The Z4550 will also operate globally on HSPA (UMTS) networks on bands 1,2,4,5, and 8 3.1 Prerequisites...
10 October 2016 3.2 Activation 1. Insert the SIM card 2. Connect the DC power source to the Z4550 and power up 3. Connect a computer to the Z4550 using an Ethernet cable, a browser, and the default administrative IP address 4.
See the Installing Radio Network Specific Firmware section above for visual indicators and timing considerations. 4 Wireless Network Activation – Z4200 3G (CDMA/EVDO/1XRTT) For CDMA models, the Provisioning function on the main menu serves two purposes. First, it provides a mechanism to activate and provision the router on the wireless networks utilizing the OTAS mechanism.
10 October 2016 Note – To insure a stable environment prior to executing an OTAP evolution the SkyRouter verifies that during the previous two minute sample period the RSSI is greater than (smaller negative number) -99dBm, the SID has not changed, and the unit has access to 1xRTT connectivity.
10 October 2016 Figure 5 5 Wireless Network Activation – Z4400 3G (GSM/UMTS/HSPA) Activating a Z4400 on a GSM/HSPA network is performed by inserting a Subscriber Identification Module (SIM) In the appropriate SIM connector and filling in information on the Wireless Interface screen that will have been provided by the Network Operator or Carrier providing the SIM.
6.1 Change the Default User ID and Password NOTE - The default User ID and password for Ctek’s SkyRouters is well known. Failure to perform this step exposes the user’s equipment to unauthorized access and tampering. Select the User Accounts function. The screen shown in Figure 4 will be presented.
10 October 2016 General Configuration Firewall Status - When enabled the firewall blocks all WAN traffic except for port 80 and the serial pad port if, and only if the serial pad is active. Since an SMS command (TechNote TN009) can be used to temporarily open ports for ad-hoc maintenance there are very few reasons to ever disable the firewall.
10 October 2016 7 Device Profile The Device Profile screen performs two key functions. First, it is used to configure the Z4550’s LAN for either network gateway or network client operation. Second, it is used to configure a number of parameters used by SkyRouter resident applications for alarming, reporting, and formatting the dashboard display.
10 October 2016 8 Local Interfaces 8.1 Overview Figures 6 and 7 below show the location of local interfaces, indicators, and controls found on the Z4550 SkyRouter. Figure 8 Figure 9 8.2 RS232/RS485 Ports The RS232/RS485 screen is used to configure the physical (electrical and timing) characteristics of the serial ports. The serial ports can be connected to the TCP/UDP PAD function for WAN transmission.
A general-purpose RS485 connection is provided on pins 13 and 14 of the top connector block. The TR1 connection can be connected to the serial (TCP/UDP/PPP) pad function (TN039), and is used to support RS485 Modbus controllers that interface with Ctek’s Automation Control application. See Application Note APN008 for details on interfacing to Modbus controllers using Automation Control.
10 October 2016 8.4 Ethernet Port Forwarding In the gateway mode of operation (see section 5.1) the Z4550 SkyRouter routes data to and from the wireless network IP connection to a class C range of local (private) IP addresses available on the RJ45 Ethernet connector. To accomplish this the Port Forwarding screen allows you to forward WAN side IP traffic arriving on a specific IP Port to a specific Port at a designated LAN side address.
The SkyCloud Services screen serves two related purposes. It provides a method of selecting a Dynamic Domain Name Service (DDNS) for the Z4550. Secondly, it is used to configure the unit for operation on Ctek’s cloud based visual access and management system, SkyCloud. See Technical Information Bulletin TIB006 for details.
SkyRouter via the USB drive. 13 Applications The Z4550 comes standard with the Automation-Light application installed. Automation-Lite is a scaled back version of the complete Automation application, which can be licensed from Ctek. See Application Note APN008 for details on the Automation application.
Need help?
Do you have a question about the Z4200 and is the answer not in the manual?
Questions and answers