1. Manuals
  2. Brands
  3. Metcal Manuals
  4. Tools
  5. QX2
  6. User manual

Metcal QX2 User Manual

Convection rework system
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
METCAL QX2 CONVECTION REWORK SYSTEM USER GUIDE
Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com
Metcal is an OK International Company
Copyright © 1999, Metcal, Inc. All Rights Reserved 7036-0540 Rev. A

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the QX2 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Metcal QX2

Summary of Contents for Metcal QX2

  • Page 1 METCAL QX2 CONVECTION REWORK SYSTEM USER GUIDE Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com Metcal is an OK International Company Copyright © 1999, Metcal, Inc. All Rights Reserved 7036-0540 Rev. A...

  • Page 2: Table Of Contents

    WARRANTY ............. 16 ® Copyright © 1999, Metcal, Inc. All Rights Reserved 7036-0541 Rev. A Copyright © 1999, Metcal, Inc. All Rights Reserved 7036-0541 Rev. A...

  • Page 3: System Overview

    The work tray can also be used to store nozzles. The nozzle removal tool provides a way to hold hot components or hot nozzles removed from the QX2. Simply hold the scoop side under the heater head to catch a hot component. To remove nozzles, see Nozzle Removal (p.12).

  • Page 4: System Set-Up

    POWER IS OFF . Always allow the system to cool before storage or re-packing. A fire may arise if not used with care. Be careful when using the QX2 in places where there are combustible materials. Never use the system in the presence of an explosive atmosphere.

  • Page 5: Attach Mode

    Place the tool directly underneath the component and push the Start/Stop button. The component will fall into the tool and the vacuum pump will turn off . Copyright © 1999, Metcal, Inc. All Rights Reserved 7036-0541 Rev. A Copyright © 1999, Metcal, Inc. All Rights Reserved 7036-0541 Rev. A...

  • Page 6: Set-Up Mode & Calibration

    BOARD HOLDER OVERVIEW The Set-up mode will allow you to change some settings of the QX2 system. To enter this mode, turn off the main power, hold down the +/- keys simultaneously and turn The board holder provides a self-centering mechanism for holding a PCB from the main power on.
  • Page 7 Option 1 Remove the nozzle. Lift the QX2 and place it over the preheater cables so that the cables are in the grooves under the QX2. Place the three tabs in the back of the preheater over the Use the notch in the Nozzle Removal Tool to pull the vacuum cup from the vacuum tube.

  • Page 8: Focused Convection Nozzles

    NZ-D2109 TSOP 28-32 NZ-D2113 TSOP 48 More nozzles may be available; contact your local Metcal representative for details. Copyright © 1999, Metcal, Inc. All Rights Reserved 7036-0541 Rev. A Copyright © 1999, Metcal, Inc. All Rights Reserved 7036-0541 Rev. A...

  • Page 9: Troubleshooting

    ERROR CODES SYMPTOM POSSIBLE CAUSE SOLUTION The QX2 is programmed to identify certain problems in the proper function of the No display on controller No power Be sure power cord is plugged into the power system. If one of these problems occurs, the system will shut down and one of the supply and a grounded outlet and the power following error codes will appear on the controller display.

  • Page 10: Warranty

    WARRANTY SPECIFICATIONS Metcal, Inc., warrants the QX2 system against any defects in materials or workmanship for one year from the date of purchase by original owner. Metcal Input voltage 220-260 VAC, 50/60 Hz warrants all other products except consumables (e.g. vacuum cups) against any...

Table of Contents