Table of Contents
Advertisement
Quick Links
Summary
● Strong anti-interference performance
● The full range of fine temperature compensation
● CE, FCC and ROHS compliant
Speci cation
● Power Supply (Receiver): DC 6 V or 1.5 V C Battery x 3
● Power Supply (PIR Transmitter): DC 4.5 V (1.5 V AAA Battery x 3 )
● Working Current (Receiver Alarming): ＜180mA
● Working Current (Receiver Chiming): ＜200mA
● Working Current (PIR Transmitter): ＜15mA
● Quiescent Current (Receiver): ＜400uA
● Quiescent Current(PIR Transmitter): ＜50uA
● Sensing Angle: 45°
● Sensing Distance: 5–8 m
● Ring Volume: ≥100dB ( within 0.5 m)
● Reception Sensitivity: ≥- 85dBm
Accessories List
● 1 x PIR Transmitter
● 3 x Wall Plugs
Names for Parts
(1) LED Indicator
(4) Switch for Chime, Low, Alarm
(7) Auto-learning Code Button
(1)
(2)
Driveway Alert Alarm Instruction Manual
● 1 x Receiver
● 3 x Screws
(2) Speaker
(5) On/Off Switch
(8) PIR
CHIME
LOW
ALARM
● 1 x Instruction Manual
(3) DC 6V Input Jack
(6) Sound-and-Flash Switch Button
(9) LED Indicator
(3)
(5)
ON
OFF
(6)
(7)
(4)
1
(8)
(9)
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for 1byone O00QH-0509
Summary of Contents for 1byone O00QH-0509
- Page 1 Driveway Alert Alarm Instruction Manual Summary ● Strong anti-interference performance ● The full range of fine temperature compensation ● CE, FCC and ROHS compliant Speci cation ● Power Supply (Receiver): DC 6 V or 1.5 V C Battery x 3 ●...
- Page 2 Battery Installation (Receiver) 1. Remove the screws on the rear of the Receiver with a cross-headed screwdriver. Remove the battery compartment cover. 2. Insert three C type batteries in the battery compartment according to the”+ -”marks. 3. Replace the battery compartment cover and secure the screws. 3 x C 1.5V Alkaline Battery Battery Installation (PIR Transmitter)
- Page 3 Receiver Unit Drill two holes on the wall at your required height. The distance between the two holes should match the two hanging holes at the back of the receiver. Then insert two wall plugs (included) into the holes. After that, insert two screws (included) into the wall plugs. Be noted that you should not insert completely the screws into the wall plug, but keep a suitable length out of the wall surface, which is to hold the receiver.
- Page 4 11.The PIR transmitter batteries’ lifespan: if a 1.5V AAA battery with capacity 1150mAh is used, based on average 10 sounds per day, 80% of the battery capacity available, these three batteries can be used for 12 months. 1byone Products Inc. www.1byone.com 2313 E, Philadelphia Street, Ontario, CA 91761...
Need help?
Do you have a question about the O00QH-0509 and is the answer not in the manual?
Questions and answers
i had to order a sensor replacement & it is not working. how do i factory reset the receiver & pair it to the new sensor?
To factory reset the 1byone O00QH-0509 receiver and pair it with a new sensor:
1. Reset the Receiver: Press and hold the auto-learning code button on the receiver for 5 seconds. The LED indicator will flash and the receiver will sound, confirming that all previous information has been deleted.
2. Pair with New Sensor:
- Press the button on the new transmitter (sensor) once.
- The receiver will sound, indicating successful pairing. Note: pressing the button once pairs only one transmitter.
This completes the reset and pairing process.
This answer is automatically generated