Advertisement
Quick Links
Download this manual
See also:
Installation Manual
GeneralTouch Zero-bezel SAW Touch Screen
Issued by: Customer Service Department
发行部门：客户服务部
Quick Installation Guide for
吉锐零边框声波触摸屏快速安装指导
GeneralTouch Technology Co., Ltd
Address: No. 6 Keyuan South Road, High-Tech Zone,
Chengdu, Sichuan Province, P.R.China.
Tel:
+86-28-85124100
Fax:
+86-28-85124150
Email:
service@GeneralTouch.com
Web:
www.GeneralTouch.com
GENERALTOUCH TECHNOLOGY CO., LTD
V1.2
1 / 13
Issued Date: 2013.10.14
发行时间：2013.10.14
Advertisement
Related Manuals for GeneralTouch SAW
Summary of Contents for GeneralTouch SAW
- Page 1 GENERALTOUCH TECHNOLOGY CO., LTD Quick Installation Guide for GeneralTouch Zero-bezel SAW Touch Screen 吉锐零边框声波触摸屏快速安装指导 V1.2 GeneralTouch Technology Co., Ltd Address: No. 6 Keyuan South Road, High-Tech Zone, Chengdu, Sichuan Province, P.R.China. Tel: +86-28-85124100 Fax: +86-28-85124150 Email: service@GeneralTouch.com Web: www.GeneralTouch.com Issued by: Customer Service Department 1 / 13 Issued Date: 2013.10.14...
- Page 2 Key Points for Assembling GeneralTouch Zero-bezel SAW Touch Screen 吉锐零边框声波触摸屏安装要点 First of all, please focus on the following summary of key points for assembling GeneralTouch Zero-bezel SAW touch system. Before, during and after the assembly, please follow each key point below to check whether the Zero-bezel SAW touch screen is assembled correctly or not.
- Page 3 GENERALTOUCH TECHNOLOGY CO., LTD transducers cannot be touched or crashed during and after assembly. Meanwhile there should be a protection clearance of at least 5mm between the structural parts and the transducers; 在触摸屏三个角的换能器需要良好的保护。 请确保安装过程中和安装完成后， 换能器不被触摸和挤压到。 同时结构件和换能器之间应至少有 5mm 的保护高度。 6) During the assembly of the touch screen, please protect the touch screen carefully against from any physical damages like scratches.
- Page 4 GENERALTOUCH TECHNOLOGY CO., LTD Introduction for Zero-bezel SAW Touch Screen 零边框声波触摸屏介绍 The locations of components of Zero-Bezel touch screen are shown in FIG.1 and FIG.2 below. 零边框触摸屏的零部件位置如下图 FIG.1 和 FIG.2 所示。 Detail C Transducer ID LABEL MAX 4.0mm Detail D...
- Page 5 GENERALTOUCH TECHNOLOGY CO., LTD The distance between the touch screen cable and the edge of glass is no more than 4mm as shown in FIG.3 below. 屏线和玻璃边缘的距离不超过 4mm，如下图 FIG.3 所示。 Cable MAX 4.0mm Detail D FIG.3 The location of touch screen cable 触摸屏线的位置...
- Page 6 GENERALTOUCH TECHNOLOGY CO., LTD GeneralTouch can adjust the location of touch screen cable according to your structure, for example to stick the touch screen cable in the area which is just the position of clearance between the rear frame and the metal frame of LCD panel for your application.
- Page 7 GENERALTOUCH TECHNOLOGY CO., LTD FIG.6 One structure of rear frame 一种后框结构 2.2 For the rear frame with the structure showed in the FIG.7 below, please tear off the PET cover, clean the original narrow double-sided adhesive tapes by alcohol carefully and then straightly and tightly stick the double-sided adhesive tapes onto the background area and keep a 1mm distance from the inner edges of background area.
-
Page 8: Notes 注意事项
GENERALTOUCH TECHNOLOGY CO., LTD FIG. 8 Right and wrong ways for sticking double-sided adhesive tapes 粘贴双面胶的正确和错误方法 2.3 Please kindly make the joints of double-sided adhesive tapes adhere to each other closely. Double-sided Double-sided Adhesive Tape Adhesive Tape Joint Tightly FIG.9 Stick double-sided adhesive tape 粘贴双面胶... - Page 9 GENERALTOUCH TECHNOLOGY CO., LTD 结构件不能对换能器和屏线施加任何的压力。 在有换能器的三个角落，为了保护触摸信号的传递，请保持保护区域没有任何残留物，包括触摸屏正面和背 面。背面的保护区域是下图所示的灰色带 45°斜实线的区域。请根据零边框屏体的图纸确定保护区域的具体 尺寸。 Protection area Protection area Protection area transducer transducer transducer Detail A Detail C Detail B FIG.10 Protection areas on the rear surface of Zero-bezel touch screen 零边框触摸屏背面的保护区域 At the same time, please reserve a protection height of at least 5mm between the transducers and the structure parts around the protection areas above.
- Page 10 GENERALTOUCH TECHNOLOGY CO., LTD No Glue or Soft material filling the gap FIG.12 Don’t fill the gap by glue or soft material 禁止用胶或软性物料填充缝隙 Postscript: Application Examples Shows 附记：应用实例展示 The following pictures show some application examples integrated with Zero-bezel touch screen.
- Page 11 GENERALTOUCH TECHNOLOGY CO., LTD The rear frame with the structure showed in FIG.7 FIG.14 15” Touch monitor with Zero-bezel touch screen 15”零边框触摸显示器 FIG.15 23” AIO computer with Zero-bezel touch screen 23”零边框一体机 Issued by: Customer Service Department 11 / 13 Issued Date: 2013.10.14 发行部门：客户服务部...
- Page 12 这样会帮助控制清洁剂的用量。如果直接将清洁剂喷到触摸屏，很容易喷洒过多的清洁液，这样混有灰尘和脏污 的清洁液就会通过前框和屏体间的缝隙渗入条纹区，影响触摸性能。 Touch Screen Transportation GeneralTouch SAW touch screen are made by glass, so proper transportation is required. Please pay attention to the following transportation warnings marked on the carton: 吉锐声波触摸屏是由玻璃加工而成，因此需要采用合理的运输方式。请注意下面在包装箱上的运输警示标识： When receiving the touch screens from the forwarder, please make sure to open the box and check the products before signing the receipt.
- Page 13 北方区 林茂 +86-28-85124100 +86-28-85124115 linmao@generaltouch.com GeneralTouch Technology Co., Ltd. reserves the rights to change or update the information contained in this document without any notification in advance. 吉锐触摸技术股份有限公司保留更改或更新此文档中的信息而不提前通知的权利。 THE END! Issued by: Customer Service Department 13 / 13 Issued Date: 2013.10.14 发行部门：客户服务部...