Justec jgs800i User Manual

8 port gigabit switch

Advertisement

Quick Links

8 Port Gigabit Switch
User's Manual
FCC Certifications
This Equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received; including interference that may cause
undesired operation.
CE Mark Warning
This equipment complies with the requirements relating to electromagnetic compatibility, EN 55022 class A for ITE, the essential
protection requirement of Council Directive 89/336/EEC on the approximation of the laws of the Member States relating to
electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it may be possible that information in this document is not
up-to-date. Please check with your local distributors for the latest information. No part of this document can be copied or
reproduced in any form without written consent from the company.
Trademarks:
All trade names and trademarks are the properties of their respective companies.
.
Copyright © 2004, All Rights Reserved

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the jgs800i and is the answer not in the manual?

Questions and answers

Summary of Contents for Justec jgs800i

  • Page 1 8 Port Gigabit Switch User’s Manual FCC Certifications This Equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
  • Page 2 Unpacking Information Thank you for purchasing the Gigabit Ethernet Switch. Before installation, please check that your package contains the following items. 1. One Gigabit Ethernet Switch 2. One power cord 3. Rack-mount brackets (optional) 4. User’s Manual Introduction General Description Easily boost your networking throughput, this switch provides you 8 Gigabit ports that lead you to a real Gigabit connection.
  • Page 3 Supports 8K MAC address entries in whole system 180K Bytes buffer memory Support up to 9K bytes jumbo Frames Supports extensive LED indicators for network diagnostics Rack mountable Internal power supply 100~240VAC/50~60Hz universal input FCC Class A, CE The Front Panel The front panel consists of LED indicators and the ports.
  • Page 4 The Rear Panel The rear panel of the switch is shown as below Power Receptacle To be compatible with the electric service standards around the world, the switch is designed to afford the power supply in the range from100 to 240VAC, 50/60Hz.
  • Page 5 brackets and screws for rack mounting the unit. Procedures to Rack-Mounting the Switch in the rack: 1. Disconnect all the cables from the switch before continuing. 2. Place the unit the right way up on a hard, flat surface with the front facing you.
  • Page 6 Product Specifications IEEE802.3 10BASE-T IEEE802.3u 100BASE-TX Standard IEEE802.3ab 1000BASE-T IEEE802.3x flow control Interface 8 * 10/100/1000Mbps auto MDI/MDI-X RJ-45 ports Network 10/100/1000Mbps Auto-negotiation Data Rate Transmission 10/100Mbps Full-duplex, Half-duplex Mode 1000Mbps Full-duplex System: Power indications Ports: 1000M, 10/100M 8K MAC entries Memory 180K Bytes Memory Jumbo frame 9K bytes...

Table of Contents