Page 1
CDC-X217 CDC-X317 CDC-X417 SERVICE MANUAL STEREO CAR CD RECEIVER BASIC CD MECHANISM: TN-CCD1001Z-152J • This Service Manual is the “Revision Publishing” and replaces “Simple Manual” of CDC-X217/ X317/ X417<YU>, (S/M Code No. 09-00C-441-1T1). S/M Code No. 09-011-441-1R1...
SPECIFICATIONS RADIO SECTION AUDIO SECTION (FM) Max. Power Output 45 W x 4 channels Frequency Range 87.5 MHz –108 MHz (100-kHz steps)* 87.5 MHz –108 MHz (50-kHz steps)* AUX IN input Usable Sensitivity 12.7 dBf Input Sensitivity (load impedance) 50 dB Quieting Sensitivity 17.2 dBf AUX IN 300 mV (10 kΩ) IF Rejection...
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING CAUTION This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing. Use of controls or adjustments or performance of proce- dures other than those specified herin may result in WARNING!! hazardous radiation exposure.
CAUTION WHEN SERVICING (1) Using extension jigs When the function of CD mechanism (TN-CCD1001Z-152J) is checked, connect between MAIN P.W.B and CD mechanism with the extension jigs. BKC-JIG(1) BKC-JIG(2) MAIN P.W.B CD Mechanism Bottom View Extension jig • As the connection connector has no polar directions, check the direction of the circuit board (BKC-JIG1/2) when installing. (Refer to the PIN number in the above photo.) Parts name JIG-BKC...
Page 5
ELETRICAL MAIN PARTS LIST REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION C210 87-A10-260-080 C-CAP,U 0.1-16 K B C211 87-010-498-040 CAP,E 10-16 GAS 87-A20-446-010 C-IC,LA9241ML C212 87-012-276-080 CAP, CHIP SS 1500 PBK 87-A21-319-010 C-IC,LC78622NE C213 87-A10-504-080 C-CAP,U 0.047-16 K B 87-A21-488-040 C-IC,LA6556...
REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION SW0001 S6-418-040-030 DET SW ESE22MH3 SW0002 S6-418-040-020 DET SW ESE22MH1 SW0003 S6-418-040-020 DET SW ESE22MH1 FLEX.C.B S3-031-100-370 PICK UP FPC(Z) CHIP RESISTOR PART CODE Chip Resistor Part Coding Figure Resistor Code Value of resistor...
Page 15
WIRING – 3 (CONN / SW / FLEX) F FLEX.C.B(1/2) 13 11 D CONN. C.B FEED MOTOR 13 11 F FLEX. C.B(2/2) OPTICAL PICK-UP TO MAIN C.B PICK-UP SPINDLE MOTOR E SW C.B (DISC DET) LOADING (DISC DET) MOTOR (DISC DET) –...
Page 22
IC501, LA4743B IC701, LC72358N-9A04 PIN NO. TUNER PIN NO. TUNER CD-CHANGER 2.32 2.75 2.75 2.75 DATA 4.76 4.76 4.76 2.74 2.74 2.74 4.66 14.38 14.38 14.38 DATA DATA DATA DATA 2.75 2.75 2.75 4.95 4.95 4.78 DATA DATA DATA DATA 2.68 2.68 2.68...
Page 26
IC DESCRIPTION IC, LC72358N-9A04 Pin No. Pin Name Description System clock oscillator input. TEST 2 Not used. CD DATA IN Input data signal for receiving from CD changer. (Not used.) Not connected. CD CLOCK IN Input synchronous clock signal for receiving from CD changer. (Not used.) E-VOL DO Data output for volume level control.
Page 27
Pin No. Pin Name Description Sub-code Q output standby input terminal. Read / write control output terminal. CD RES DSP reset output terminal. Disc detection / chuck or release disc detection. 12 cm disc detection / 12 cm disc ejection and detection. Leading motor start detection.
Page 28
IC, LA9241ML Pin No. Pin Name Description For the connection of the pickup photodiode. Addition to the FIN1 pin creates an RF signal FIN2 and subtraction from it create an EF signal. FIN1 For the connection of the pickup photodiode. For the connection of the pickup photodiode.
Page 29
Pin No. Pin Name Description CLV error signal input from the DSP. RFSM RF output. RFS- Set the RF gain and the EFM singal's 3T compensation constant together with the RFSM pin. The SLC (slice level control) signal is output to control the DSP's data slice level of the RF waveform.
Page 30
IC, LC78622NE Pin No. Pin Name Description DEFI Defect detection signal (DEF) input. (Must be connected to 0V when not in used.) For PLL/Test input. A pull-down resistor is built-in. (Must be connected to 0V.) External VCO control phase comparator output. VVSS Internal VCO ground.
Page 31
Pin No. Pin Name Description XOUT Connection for a 16.93 MHz crystal oscillator element. XVSS Crystal oscillator ground. (Must be connected to 0V.) SBSY Subcode clock synchronization signal output. (Not used) EFLG C1, C2, signal a double error correction monitor. (Not used) Subcode P, Q, R, S, T, U and W output.
Page 32
IC, LC75374E Pin No. Pin Name Description RVR IN 4dB volume control input. Must be driven at a low impedance. R COM 1dB volume control common pin. For the connection of capacitors that compensate for bass and treble in the tone control circuits. 3 ~ 5 RT1 ~ RT3 A high-frequency compensation capacitors must be connected between T1 and T2.
Page 33
Pin No. Pin Name Description TUN(R) Signal input pin. CHG(R) Connected to ground. AUX(R) Signal input pin. RSELO Input selector output pin. IC, LC75853NW Pin No. Pin Name Description 1 ~ 32 S1 ~ S32 LCD segment output. Not connected. 34 ~ 39 S34 ~ S39 Not used.
CD TEST MODE 1-1 Activating CD Test Mode Add Wire 1) Remove the resistance (R757 100kΩ) of the 63 pin (test) for the IC701 (LC72358N-9A04) on the main circuit board, and connect the 73 pin (VDD) and the 63 pin with a wire. REMOVE 100kΩ...