Table of Contents
Advertisement
02
Connecting Up
2
Rear panel connections
Connect the analog AUDIO OUT L/R
and VIDEO OUT jacks on this player to a
set of analog audio and video inputs on
• Before unplugging the player from the
your AV receiver.
power outlet, make sure you first switch
it into standby using either the front
panel
DIGITAL AUDIO OUT
remote control, and wait of the -OFF-
COAXIAL
message to disappear from the player's
display.
AV receiver
OPTICAL
• For the above reasons, do not plug this
player into a switched power supply
found on some amplifiers and AV
8
receivers.
DIGITAL AUDIO OUT
COAXIAL
When connecting this player up to your
TV, AV receiver or other components,
Using other types of video
OPTICAL
S
make sure that all components are
output
switched off and unplugged.
This player has standard (composite),
1
DIGITAL AUDIO OUT – COAXIAL
S-Video and component video outputs. The
For connection to a PCM, Dolby Digital, DTS
main difference between them is the quality
The diagram shows standard video connec-
and/or MPEG-compatible AV receiver that
of the picture. S-Video delivers a better
tions, but you can alternatively use the S-
has a coaxial digital input.
picture than standard composite video, while
Video or component video connections if
Connect using a commercially available
component video gives better picture quality
they're available.
coaxial digital audio cable.
still. The variety of outputs also gives you the
flexibility of connecting your particular
3
Connect the AV receiver's video
2
COMPONENT VIDEO OUT
equipment using the best connection type
output to a video input on your TV.
For connection to a TV, monitor or AV
available.
receiver that has component video inputs.
Connect using a commercially available
Connecting using an S-Video
three-way component video cable. Match the
• You usually have to connect the same
output
colors of the jacks and cables for correct
kind of video cable between your DVD
connection.
You can use the S-Video output instead of the
player and AV receiver, and between
VIDEO OUT jack to connect this player to
your AV receiver and TV.
3
AUDIO OUT L / R
your TV (or other equipment).
For connection to your TV, AV receiver or
stereo system. Even if you are connecting up
1
Use an S-Video cable (not supplied)
one of the digital outputs, we still recom-
to connect the S-VIDEO OUT to an
mend you connect these jacks.
S-Video input on your TV, monitor or
AV receiver.
Connect using the supplied audio/video
Line up the small triangle above the jack
cable. Match the colors of the jacks and
with the same mark on the plug before
cables for correct stereo sound.
plugging in.
4
AC IN
Connect the supplied power cord here, then
plug into a power outlet.
10
12
14
Downloaded From DvDPlayer-Manual.com Pioneer Manuals
Downloaded From DvDPlayer-Manual.com Pioneer Manuals
Downloaded From DvDPlayer-Manual.com Pioneer Manuals
En
En
En
1
2
3
STANDBY/ON button, or the
AUDIO OUT
Y
P
B
L
R
AUDIO/
P
R
VIDEO INPUT
COMPONENT VIDEO OUT
S
VIDEO OUT
7
6
AUDIO OUT
Y
P
B
L
R
P
R
COMPONENT VIDEO OUT
VIDEO OUT
• My TV doesn't have any inputs to
connect the DVD player. How can I watch
DVDs?
Unfortunately, if your TV has no inputs
D1 VIDEO OUT
you can't use this player with it.
TV
• My VCR is already connected to my TV, so
DIGITAL AUDIO OUT
there aren't any spare inputs. What
Y
COAXIAL
should I do?
5
If all your TV's inputs are already in use,
OPTICAL
S
VIDEO OUT
you can buy a video input selector from
5
D1 VIDEO OUT (Taiwanese model only)
an electronics store, which effectively
Use to connect this player to a TV with a D
gives you more inputs.
video input.
• My TV only has one input for the sound.
6
VIDEO OUT
What should I plug it into?
Connecting using the component
For connection to your TV or AV receiver
If you don't mind mono sound, you can
using the supplied audio/video cable.
video output
buy a stereo RCA-to-mono RCA cable
You can use the component video output
from an electronics store. Connect the
7
S (S-Video output)
instead of the VIDEO OUT jack to connect
stereo end to this player and the mono
For connection to your TV or AV receiver
this player to your TV (or other equipment).
end to your TV.
using a commercially available S-Video
cable.
If you want stereo sound, connect this
1
Use a component video cable (not
player to your amplifier or stereo system
supplied) to connect the COMPONENT
8
DIGITAL AUDIO OUT – OPTICAL
using a stereo audio cable.
VIDEO OUT jacks to a component video
For connection to a PCM, Dolby Digital, DTS
input on your TV, monitor or AV receiver.
and/or MPEG-compatible AV receiver that
• I connected the DVD player to my AV
has an optical digital input.
receiver, and although the sound is fine,
there's no picture. What did I do wrong?
Connect using a commercially available
optical digital audio cable.
Make sure that the type of video
connection from the DVD player to your
AV receiver is the same as that from the
receiver to your TV. Most AV receivers
• You may find it useful to have the
won't convert from one kind of connec-
manuals supplied with your other
tion to another.
components handy when connecting
this player.
• If you come across any unfamiliar terms
in this section of the manual, take a look
at the Glossary starting on page 51.
4
S-VIDEO
INPUT
AUDIO OUT
P
B
L
Taiwanese model
R
P
R
COMPONENT VIDEO OUT
Advertisement
Table of Contents
