Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Eastwood 30117
Summary of Contents for Eastwood 30117
- Page 1 Item #30579 PORTABLE GENERATORS INSTRUCTIONS FOR 30117 & 30118 30118 30117...
-
Page 2: Specifications
EASTWOOD GAS POWERED GENERATORS are CARB/EPA certified so they are 50-state compliant and are very fuel efficient for longer run times. The electric generator on the EASTWOOD GAS POWERED GENERATORS use only pure copper-wound heads to provide a very reliable generator that will run at full load for extended periods of time without overheating. -
Page 3: Safety Information
• Always disconnect the spark plug wire and place the wire where it cannot contact the spark plug to prevent accidental starting when setting up, transporting, adjusting or making repairs to the generator. To order parts and supplies: 800.345.1178 >> eastwood.com... -
Page 4: Fire And Explosion Hazard
• Never leave the Generator unattended while running. • The RPM level and phasing is set at the factory to produce 60 Hz. Never tamper with the governor or throttle assembly or damage to electronic devises may occur. Eastwood Technical Assistance: 800.544.5118 >> techelp@eastwood.com... -
Page 5: Control Panel Features
(I) Low Oil Warning Lamp (B) 12V DC Outlet (F) 20A Circuit Breakers (J) Ground Post (C) Voltage Meter (G) L5-30R 120V AC Twist Lock Receptacle (D) 12V DC Circuit Breaker (H) Main Circuit Breaker To order parts and supplies: 800.345.1178 >> eastwood.com... - Page 6 Retaining Knob (Item 7) into hole on right upper side of Generator Frame at Handle base (Fig E). Thread into the spring-loaded, retractable button and tighten Knob securely. FIG. D FIG. E Knob (7) Eastwood Technical Assistance: 800.544.5118 >> techelp@eastwood.com...
- Page 7 - Connect a 6 Ga. copper ground wire (not included) to the Ground Terminal lug located on the lower right of the Control Panel (“M” on # 30118 Panel, “J” on #30117 Panel). - Attach the opposite end of the ground wire to a copper or brass grounding rod FIG.
-
Page 8: Starting The Generator
4. Choke - Move the Choke lever located to the rear of the generator on the Carburetor to the “CLOSED” position (Fig O). NOTE: With a warm engine being restarted after refueling, it may not necessary to close the Choke before starting. Eastwood Technical Assistance: 800.544.5118 >> techelp@eastwood.com... - Page 9 - Key Start Switch - Turn the Ignition Key Switch located on the left side of the Starter FIG. S Control Panel to the “STOP” position (Fig R). Handgrip DO NOT close choke to shut off engine. FIG. T Open Choke Closed To order parts and supplies: 800.345.1178 >> eastwood.com...
-
Page 10: Electrical Loading
The following chart is provided as a guide to average power require- ments in Watts for some of the most common electrical demand 100 Watt Light Bulb items that may be used when operating your Eastwood gasoline 1/3 HP Sump Pump 1200 powered generator. -
Page 11: Shutting Down The Generator
6. After Generator is completely cooled, move it to a clean, dry location and cover with a suitable cover. NOTE: A small barbecue grill cover will work well. 7. #30118 Only – Disconnect Battery Terminals for short-term storage. Remove battery for long-term and storage in sub-freezing temperatures. To order parts and supplies: 800.345.1178 >> eastwood.com... -
Page 12: Maintenance
DO NOT USE GASOLINE. 5. Carefully reinstall Fuel Bowl and O-Ring using care not to pinch it. 6. Reinstall Drain Plug and tighten firmly but not over tight. 7. Open Fuel Valve. Check for leaks. Eastwood Technical Assistance: 800.544.5118 >> techelp@eastwood.com... - Page 13 Used Plug: 1/8 to 1/4 Turn after Spark Plug seats to fully compress sealing washer. 9. Reinstall Spark Plug Boot by pushing onto plug and seating it securely. NOTE: Failure to fully seat Spark Plug Boot will prevent Plug from sparking. To order parts and supplies: 800.345.1178 >> eastwood.com...
-
Page 14: Troubleshooting
TROUBLESHOOTING The following chart is intended to provide solutions to the most frequent problems encountered when operating your Eastwood gasoline powered generator. Other more serious mechanical or electrical malfunctions may be present and can require the attention of a professional small-engine repair facility. -
Page 15: Replacement Items
Fuel Filter & Petcock Gasket ADDITIONAL ITEMS #30497 6 Circuit Transfer Switch #30498 10 Circuit Transfer Switch #12736Z Eastwood Fuel Stabilizer #70468 30 LED Retractable Worklight #70248 Rechargeable LED Worklight #30189 6 LED Penlight To order parts and supplies: 800.345.1178 >> eastwood.com... -
Page 16: Statement Of Limited Warranty
At Eastwood’s request, the purchaser must take the faulty product to an Eastwood approved repair facility for a complete diagnostic inspection to determine the cause of the failure. The cost of the diagnostic inspection will not be covered by Eastwood unless there is a determination that there is a coverable repair. Once the repair facility has determined the cause of the failure, the repair facility will call 1-800-345-1178 with the authorization number to report their findings.