Advertisement
Troubleshooting guide
Sound
Page
No
sound.
Low
volume.
Distorted
sound.
•
Check
the
connections.
Check
the
input
mode
on
the
amplifier
if
you have connected
one.
• Turn
V.S.S.
off
if
it
causes
distortion.
10, 46,
47,
48
43
Cannot
hear the desired
audio
typ6.
• Press [AUDIO]
to select
the desired
audio
type.
•
Go
to
Audio
in
the
SETUP
menus
and choose
the correct
setting
with "Select
MTS
for
DVD-R
or
LPCM".
26
53
Cannot
switch
audio during
stereo or
SAP
broadcasts.
• You
have used
digital
connection.
Set "Dolby
Digitar to
"PCM"
or
connect
to
other
equipment
using audio cables (analog connection).
•
You cannot
change
the
audio type
when
using
DVD-R
or with
LPCM
recordings.
47, 51
Ptay
Play
fails
to start
even
when
[](PLAY)
is
pressed.
Play
starts
but
then stops
immediately.
•
Insert
the disc
correctly with
the
label
lacing up.
•
This
unit
cannot
play discs
other
than
DVD-RAM.
DVD-R,
DVD-Video, Video
CD,
and
CD.
•
The
disc
is dirty.
Clean
it.
•
The
disc
may
be
badly scratched.
•
You
inserted
a blank
DVD-RAM
or
DVD-R.
• Condensation has
formed: Wait
1
to
2 hours
for
it
to
evaporate.
17
8
9
A
title
or
chapter doesn't
play
when
it
is
selected.
•
Some
titles
and
chapters
on DVD-Video
are not played
when
you have changed
the
ratings
level.
51
Picture distorted
during
search.
•
Some
distortion
is
normal.
Alternative
soundtrack
and
subtitles
cannot be
selected.
•
The
languages
are
not
recorded
on
the
disc.
•
Ybu
may
have
to
use
the
disc's
menus
to
select
languages.
17
No
subtitles.
•
Subtitles
are not
recorded
on
the
disc.
• Turn
the
subtitles
on.
42
Angle cannot be changed.
•This
function
depends on
software
availability.
Angles can
only
be changed
during
scenes
where
different
angles are
recorded.
You have
forgotten
your
rat-
ings
password.
•
Return
the
ratings setting
to
"8".
While
the
disc
tray
is
open, press
and
hold
[
W^/"^"^] and
{/!]
on
the
main
unit
at
the
same
time
for
5
or
more
seconds.
Displays
The
display
is
dim.
•
Go
to
Display
in
the
SETUP
menus
and change
the
display's
brightness
with
"FL
Display".
53
"12:00"
is
flashing
on
the
unit's display.
•
The
clock
is
not
set.
Set
the
clock.
11,
12
The
displayed recording time
and
actual
recording time
dif-
• Displayed recording time
is
calculated
based on
the
number
of
frames recorded
per second.
This
number
is
subject
to
minute
variation.
When
the recording time
is
long the
cumulative
effect of
these
small differences
may
result
in
the
slight
variation
you
may
sometimes
find
between
displayed recording time
and
actual recording time.
This
is
normal.
Remote
control
The
remote
control doesn't
work.
•
[DVD, TV]
is
not
switched
to
"DVD". Switch
to
"DVD"
when
selecting the receiving
channel
for
this
unit.
•The
remote
control
and main
unit
are using
different
codes.
Change
the
code on
the
remote
control
or
main
unit.
•The
batteries
are
depleted.
Replace
them
with
new
cmes.
•
PcMnt
the
remote
control
at
the
remote
control
sensor
on
the
main
unit.
•
Remove
obstacles from
between
the
remote
control
and main
unit.
6
SO
9
9
Cannot
operate the
televi-
sion.
•
Change
manufacturer code.
Some
televisions
cannot
be
operated
even
if
you change
the
code.
•
[DVD, TV]
is
not
switched
to
TV".
Switch
to
TV"
when
selecting
the
receiving
channel
for
the
television.
IS
6
Advertisement
