Advertisement
Error
messages
On
the
television
Page
No
disc
• You
haven't inserted
a
disc.
Correctly
insert
a
disc that
this unit
can
use.
•The
disc
is
upside
down.
If it
is
a
single-sided
disc, insert
it
so
the
label
is
facing up.
8
17
This
is
non-recordable
disc.
•
The
unit
cannot
record
on
the disc
you
inserted.
The
unit
cannot
record
onto
finalized
DVD-R,
DVD-Video,
CDs,
or
vidon
Insert
a
DVD-RAM
or
unfinalized
DVD-R.
•
You
Inserted
an
unformatted
DVD-RAM.
Format
the disc with
this
unit.
8
34
This disc
is
not formatted
properly.
Please format the disc
in
'DISC
SETTING'
to
record.
This disc
cannot be
read.
•
You
inserted
an
incompatible
disc.
Insert
a
compatible
disc.
8
Please
checit write protect tab
on
the
disc.
•
The
write-protect
tab
on
the cartridge
is
set to
PROTECT
Use
a
ballpoint
pen
or
similar to
release the
write protection.
—
Contents
of
this
disc are
protected.
•The
program
is
write -protected.
Release
the
protection with the Direct Navigator.
•The
disc
is
write-protected.
Release
Disc
Protection
with
DISC SETTING.
36
34
•
The
program
was
copy-guarded.
•
The
disc
is
full.
• Recording
was
not
completed
for
some
other reason.
—
Cannot
record
on
the
disc.
•The
disc
is
scratched.
Use
another
disc.
•
The
disc
is dirty.
9
•
The
clock
is
not
set.
Set the
clock.
11,
12
This disc
may
not
be
played
in
your
region.
•
You
tried to
play
a
disc with
a
region
number
different
from
this unit's
region
number. This
unit
can
only play discs with
the region
numbers
compatible
with
this unit
(1
,
All,
or
includ-
ing
the
number
1).
Cover page
Your
selection
exceeds
the
recorder's rating
limit.
•
A
ratings
ievel lias
been
set
for
DVD-Video
with
this
unit.
Unlock
the
unit
with "Ratings"
in
"Disc"
in
the
SETUP
menu.
51
On
the
unit's
display
U11
NO
DISC
•The
disc
is
dirty
or
badly scratched.
-Clean
the
disc
if it
is dirty.
-The
disc
cannot
be
played
If
it
Is
scratched
and
this
display
doesn't disappear.
•You
have
Inserted
a
disc the
unit
cannot
play or record on.
Insert
a
disc the
unit
can
play or
record
on.
9
8
U14
CM
•
The
unit
is
hot.
-The
unit
switches
to
standby
automatically
for
safety rea-
sons and you cannot
operate
it.
Wait
for
about
30
minutes
for
the service
number
to
disappear.
-Select a
position with
good
ventilation
when
installing
the
unit.
-Do
not block the cooling fan
on
the rear
of
the
unit.
U99
•
The
unit
fails
to
operate
properly.
Press
[d),
DVD POWER]
to
switch the
unit to
standby.
Now
press
[(!),
DVD POWER]
again
to turn
the
unit
on.
CHK REMOTE
•
The
remote
control
and main
unit
are using
different
codes.
Change
the
code on
the
remote
control or
main
unit.
50
RECOVER
•
A
power
cut
occurred
or the
AC
plug
was
disconnected
while
the
power
was
on.
The
unit
is
carrying out
its
recovery process. Wait
until
the
message
disappears.
Advertisement
