Advertisement
Fully
A
u
t o m a t i c
Fully
A u t o m a t i c
m
m
c
c
Suitable for both new,old,dirty,tattered polymer bills and paper bills
oney
oney
ounter
ounter
"SE7/25"then press
"+""-"
buttons to choose the desired
Sensitivity level (range from 0-255). After choosing of the level, press
"RESET"button to confirm.
<Double Detection function <available for the models with UV
detection or the model with both UV and MG/MT detection>.
---used to check a double-note
--By default, serving as a supplementary function, the detection can
be activated when the unit is powered up.
--If the machine detects a double-note when counting, it will stop and
emit beeping sound, while the batch display will show the message
"d3"(alerting the user the of the presence of a double-note). The
double-note will always be the last one on the stacker. Remove the
dubious bill, press"RESET"button to continue.
<Half-note Detection<available for the models with UV detection or
the model with both UV and MG/MT detection>.
---used to check half-note.
--By default, serving as a supplementary function, the half-note
detection can be activated when the unit is powered up.
--If the machine detects a half-note when counting, it will stop and
emit beeping sound, while the batch display will show the message
"d5"alerting the user the presence of a half-note bill). The dubious
bill will always be the last one on the stacker. Remove the dubious
bill, press"RESET"button to continue<the counting display will
clear>.
5
CAUTION:
1. It is highly recommended to contact the authorized service center
or local dealer before you do the above adjustments.
2. Improper adjustments may cause improper working condition or
false detection results.
7.Fake money alarm
When fake money pass the machine, the
counting will stop and alarm. The function
display will show the error code. The last
note on the stacker normally is the fake
money. The machine counting quantity
number is not included in this note. remove
the fake money. Press"RESET"button,
the machine will start counting again.
Fake money or questionable money
Fully
A
u
t o m a t i c
Fully
A u t o m a t i c
m
m
c
c
Suitable for both new,old,dirty,tattered polymer bills and paper bills
oney
oney
ounter
ounter
8.Error code and solution
The batch display may show some error code when counting,
which means there are some problems with the machine.
Refer to the following diagram to find way to solve it.
Message
Error
Solution
Remove the suspicious bill on the
Suspicious bill detected by
stacker, press "RESET"to
UV system;
continue;
Problem in the UV system.
Lower the UV sensitivity.
Remove the suspicious bill on the
Suspicious bill detected by
stacker,press "RESET"to
MG/MT system; Problem in
continue;
the MG/MT system.
Lower the MG/MT sensitivity.
Double-note detected by
Remove the suspicious bill on the
3
stacker, press "RESET" to
IR system;
continue;
Problem in the IR system.
Lower the IR sensitivity.
Note of size problem
Remove the suspicious bill on the
detected by size detection
stacker, press "RESET" to
system; Problem in the size
continue;
detection system.
Lower the size checking sensitivity.
Half-note detected by
Remove the suspicious bill on the
half-note detection system;
stacker,
press "RESET"to continue.
Problem in the half-note
detection system.
Slope-note detected by slope-
note detection system;
Remove the bill from the stacker.
Problem in the slope-note
Press "RESET" to continue.
detection system
Chain-note detected by chain-
Remove the bill from the stacker.
note detection system;
Problem in the chain-note
Press "RESET" to continue.
detection system
Message
Error
Solution
Problem with the left
E01
Clean the sensor or replace it.
counting sensor.
Problem with the
E02
Clean the sensor or replace it
right counting sensor
Problem with the
E03
Clean the sensor or replace it
speed sensor
E04
Problem with the
Clean the sensor or replace it
auto start sensor
Problem with the
E05
Clean the sensor or replace it
preset sensor
E10
Problem with the
Clean the sensor or replace it
UV sensor
< NOTE >
Generally speaking, most of the above-mentioned problems
may be caused by dust or dirt inside of the machine. So
keeping the machine clean is highly recommended .
9.Hopper adjustment
--When improper feeding of bills occur, adjust the feeding thickness
setting in the hopper by turning the adjustor screw located in the back
of the machine to ensure proper feeding.
6
Advertisement
