Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Genesis CCTV BC-540DNI
Summary of Contents for Genesis CCTV BC-540DNI
- Page 1 P r o d u c t Ma n u a l B C - 5 4 0 D N I...
-
Page 2: Box Camera
Box Camera : Color Day/Night w/ICR Vision with Integrity www.genesiscctv.com... -
Page 3: Table Of Contents
Thank you for purchasing HQ Day&Night Camera. Before using the camera, please read this operation manual carefully to obtain the best result and keep this manual for future reference. Table of Contents FEATURES ······························································· 3 CAMERA INSTALLATION ······································16 Installation & Tripod Mounting Base NAME &... -
Page 4: Features
FEATURES • Back light compensation • Day & Night When a camera scene has a strong light source The Optical Low Pass Filter is switched that shines toward the camera objects in the automatically and converts the image to color or foreground will appear as silhouettes. -
Page 5: Name & Function
NAME & FUNCTION (Front Panel) - Page 6 1. Lens mount Mount for lens installation. C-mount lens can be used when C-mount adapter is attached and CS- mount lens can be used when it is removed. 2. Lens connector When using an auto iris lens, connect the lens cable to this connector. See page 10. 3.
-
Page 7: Rear View & Function
REAR VIEW & FUNCTION... - Page 8 1. Video output connector BNC connector that outputs a composite video signal. 2. DC Iris level Adjusts the lens iris level when using a DC(direct drive) type auto iris lens. 3. V-Phase adjust Adjusts the phase when cameras are using the line lock function. 4.
-
Page 9: Lens Connector
Lens Connector When using an auto IRIS lens, connect the lens cable to the lens plug. • Video IRIS type lens : Set lens switch to VIDEO, and put the lens cable into the lens connector. If the plug on the cable is a different type, replace it with the provided 4-pin iris plug. -
Page 10: Setup Switch
Setup Switch 1. AGC (Automatic Gain Control) At the AGC on setting, camera’s sensitivity is automatically increased when the level of ambient light drops. AGC function automatically controls signal gain in the range of maximum 34dB. 2. E.E/A.I (Electronic Shutter Control) When using a fixed IRIS lens, the brightness of the picture image will be fixed by setting E.E mode as the shutter speed is automatically varied in the range of 1/60 to 1/100,000 sec according to the incident light. - Page 11 3. BLC (Back Light Compensation) Strong light, such as a spotlight, entering the scene back ground causes the lens iris to close, thereby possibly obscuring desired portions of the scene. Backlight compensation function automatically adjust the light level compensation, so that user can always obtain a clear picture, the finest detail and perfect light contrast.
- Page 12 5. ATW (Auto-Tracking White Balance) At the ATW on setting, color temperature is automatically adjusted and true color image can be shown. PUSH : White balance is fixed under the present light temperture. 6. Video Voltage Adjustment(Optional) The longer cable installed, the lower Ω(ohm) rate applied. 75Ω...
- Page 13 • L.L/INT(Line-Lock/Internal) Line lock or internal sync mode are automatically selected by the type of power supply used to power the camera. When using the camera in line lock mode(with an AC supply) it is possible to adjust the V phase alignment between 0 and 270 degrees.
-
Page 14: Lens Installation
LENS INSTALLATION • Please connect a lens cable when DC type lens or Video type lens is applied. • E.E/A.I switch on the rear panel should be set to E.E position when manual IRIS lens is used. • When using a Video type lens please adjust the iris level using the lenses onboard adjusters. -
Page 15: Mounting A Lens
• Mounting a lens Remove the lens mount cap from the camera Attach or remove the C-mount adapter depending on the lens to be used. - If the adapter is attached so tightly that is difficult to remove, use long - nosed pliers to remove it. -
Page 16: Back-Focus Adjustment
• Back-Focus Adjustment - When a lens is mounted, Back-Focus Adjustment can be required. Adjust with the lens focus ring when the correct focus cannot be obtained. • With a Fixed-Focus Lens - Fully open the aperture and set the focus ring to “∞”(infinity). -
Page 17: Camera Installation
CAMERA INSTALLATION • Installation Camera can be installed on a tripod or a fixing part from the upper or the bottom plate by using the camera fixing holes (1/4, 20UNC) on the tripod mounting base. The tripod mounting base is attached on the bottom plate when shipped from factory. -
Page 18: Specification
SPECIFICATION (Day&Night Camera) BC-540DNI True Day/Night Day/Night(ICR) Image Sensor Sony 1/3” Super HAD CCD Signal System NTSC Effective Pixels 410K Scanning System 525Lines 2:1 Interlace Scanning Frequency (H)15.734KHz(V)59.94Hz Sync.System Internal(12VDC)/L.L(External, 24VAC), Automatic Switching Video Output 1Vpp, 75Ω, Composite Video Signal... -
Page 19: Supplied Accessories
SUPPLIED ACCESSORIES - Lens connector plug - Lens mount cap - L-Wrench - Operation manual - Triped Mounting Base - Triped fixing screw x 4 - C-Mount adapter • The lens mount cap and CS-mount adapter are attached when supplied. Note : Design and specifications are subject to change without notice. - Page 21 Vision with Integrity www.genesiscctv.com Design and specifications are subject to change without notice. Printed in Korea(2009.12)