Page 1
IM3030 04/2011 REV01 POWERTEC 365S, 425S & 505S OPERATOR’S MANUAL LINCOLN ELECTRIC BESTER Sp. z o.o ul. Jana III Sobieskiego 19A, 58-260 Bielawa, Poland www.lincolnelectric.eu...
Page 2
Declaration of conformity LINCOLN ELECTRIC BESTER Sp. z o.o. Declares that the welding machine: POWERTEC 365S, 425S, 505S conforms to the following directives: 2006/95/CEE, 2004/108/CEE and has been designed in compliance with the following standards: EN 60974-1, EN 60974-10 (2005) Paweł...
Page 3
07/06 Do not dispose of electrical equipment together with normal waste! In observance of European Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE) and its implementation in accordance with national law, electrical equipment that has reached the end of its life must be collected separately and returned to an environmentally compatible recycling facility.
12/05 THANKS! For having choosen the QUALITY of the Lincoln Electric products. • Please Examine Package and Equipment for Damage. Claims for material damaged in shipment must be notified immediately to the dealer. • For future reference record in the table below your equipment identification information. Model Name, Code & Serial Number can be found on the machine rating plate.
Safety 11/04 WARNING This equipment must be used by qualified personnel. Be sure that all installation, operation, maintenance and repair procedures are performed only by qualified person. Read and understand this manual before operating this equipment. Failure to follow the instructions in this manual could cause serious personal injury, loss of life, or damage to this equipment.
CYLINDER MAY EXPLODE IF DAMAGED: Use only compressed gas cylinders containing the correct shielding gas for the process used and properly operating regulators designed for the gas and pressure used. Always keep cylinders in an upright position securely chained to a fixed support. Do not move or transport gas cylinders with the protection cap removed.
Page 7
12. Power Input Cable: Connect the proper plug to the Welding Voltage Changing Switches. The input cable then into the rated output according to POWERTEC 365S, 425S and 505S have 2 appropriate rules. Only qualified personnel shall switches (3 and 10 steps).
Page 8
Setting Welding Voltage Transport WARNING To ensure safety transport it is necessary to: • lift only power source without gas cylinder, cooler and wire feeder, • screw down an eye bolt and apply load axially in 45 Maintenance degree angle in accordance to the drawing. •...
Electromagnetic Compatibility (EMC) 11/04 This machine has been designed in accordance with all relevant directives and standards. However, it may still generate electromagnetic disturbances that can affect other systems like telecommunications (telephone, radio, and television) or other safety systems. These disturbances can cause safety problems in the affected systems. Read and understand this section to eliminate or reduce the amount of electromagnetic disturbance generated by this machine.
Spare Parts 12/05 Part List reading instructions • Do not use this part list for a machine if its code number is not listed. Contact the Lincoln Electric Service Department for any code number not listed. • Use the illustration of assembly page and the table below to determine where the part is located for your particular code machine.
Page 12
SP50149/50151/50153 REV01 04/11 POWERTEC 365S, 425S & 505S Assembly Figure Code NO. K NO. Product Name 50149 K14061-2A POWERTEC 365S 50151 K14062-2A POWERTEC 425S 50153 K14063-2A POWERTEC 505S Figure A Figure A Description Index Qty. BLACK FRAME SHIELD 1115-299-073R SWITCH...
Accessories K10347-PG-xM Source/wire feeder cable (gas). Available in 5, 10 or 15m. K10347-PGW-xM Source/wire feeder cable (gas and water). Available in 5, 10 or 15m. K14009-1 Socket Kit. KP14016-0.8 Solid: KP14016-1.0 0,6-0,8mm KP14016-1.2 0,8-1,0mm 1,0-1,2mm KP14016-1.6R Cored wires: 1.2-1.6mm KP14016-1.2A Aluminum wires: 1,0-1,2mm KP14017-0.8...
Page 20
MANUAL REVISIONS DO NOT PRINT THIS PAGE IN THE MANUAL. REV 0: • Beta phase Manual English / Portuguese. REV01 Spare parts was changed. Title page and page II were changed. PRINT THIS MANUAL ACCORDINGLY WITH THE PROCEDURE DT0052.