Related Manuals for Childcare vector pro 015616
Summary of Contents for Childcare vector pro 015616
- Page 1 VECTOR PRO Stroller Model # 015616 IMPORTANT: RETAIN FOR FUTURE REFERENCE, READ CAREFULLY...
- Page 2 Safety Precautions Read all instructions before assembly and use of the stroller. Keep instructions for future use. WARNING TO AVOID INJURY OR DEATH: FOLLOW THE MANUFACTURER’S INSTRUCTIONS. ALWAYS APPLY THE BRAKES WHENEVER THE STROLLER IS STATIONARY. USE THE TETHER STRAP AT ALL TIMES TO PREVENT THE STROLLER ROLLING AWAY.
- Page 3 Assembly contents list Assembly / Operating instructions How to care for your Childcare Stroller Due to variations in the style and design of our products, the photographs and illustrations shown in this instruction manual are generic, therefore product fabrics, colour and design may vary from images shown.
- Page 4 Assembly Contents Check what you have received... You have received 1 box. Please check the contents of the box against the list below. If anything is missing, please contact Customer Service. In Australia, contact CNP Brands on 1300 667 137, in New Zealand contact Wainhouse Distribution on 0800 567 5000.
- Page 5 Assembly / Operating Instructions Unfolding the stroller Release the folding lock as high- lighted in the image right. Lift handle and seat apart until the frame clicks and locks on both sides. Ensure the stroller is locked on both sides before using. Front / rear swivel wheels assembly Make sure the swivel lock is unlocked by pushing down to lowest point.
- Page 6 Assembly / Operating Instructions Swivel function To lock swivel wheels, push lever up To unlock swivel wheels, push lever down. HELPFUL HINTS To make it easier to steer we highly recommend that only two wheels Unlock be in a swivel motion at any time (regardless of handle position). Lock To use brakes To lock brakes, push down on each brake lever with foot.
- Page 7 Assembly / Operating Instructions Restraints - Harness To secure the child in the harness, place left hand buckle prong (b) on top of (a). Hold both left hand buckle prongs (a) and (b) together and insert it into buckle housing (e) until it snaps into position.
- Page 8 Assembly / Operating Instructions Reversing handle To reverse handle, pull up on both handle reverse levers situated on each side of handle. Reverse handle and lock it into position. Handle reverse lever Using four wheel steering This unit has a reversing handle with four swivel wheels. PLEASE NOTE: To make it easier to steer we highly recommend that only two wheels be in a swivel motion at any time (regardless of handle position) and the correct set-up as follows: Forward facing mode...
- Page 9 Assembly / Operating Instructions To adjust canopy To open canopy, pull forward. To close canopy, pull back. CAUTION: The canopy must be fully closed before folding the stroller Mesh canopy extension Unzip the rear section of canopy to use the mesh canopy extension. Zip extension closed when not in use...
- Page 10 Assembly / Operating Instructions Bootcover To attach bootcover, raise seat extension and attach press studs underneath the seat extension to the matching press studs on the inside of the bootcover as show in diagram. Insert the top flap of the bootcover underneath the bumper bar and insert the elastic loops into the seat liner’s side slots on both sides to secure it in place.
- Page 11 Assembly / Operating Instructions Folding the stroller Before folding the stroller, remove bootcover, close the hood, place seat in full layback position and transfer handle to rear (forward facing mode). Simultaneously lift the red levers located on both sides of the stroller.
- Page 12 Assembly / Operating Instructions Attaching infant carrier to stroller To remove first plastic peg This stroller is designed for use with Britax (Orion/Strider/Cruiser) infant carrier. Remove armrest’s fabric cover by: • Holding the fabric cover firmly and pull it away from the armrest to release the first plastic peg (located underneath the fabric cover).
- Page 13 Assembly / Operating Instructions Attaching infant carrier to stroller (cont.) Insert the infant carrier into the armrest slots so orientation matches photo (right). Push both of the locking handles of the infant carrier in (a) and swing handle down until you hear the lock ‘click’ into place (b). WARNING: Ensure the infant carrier is fully engaged and locked into stroller armrests before use.
- Page 14 Assembly / Operating Instructions To remove infant carrier from stroller (cont.) Close both armrest plastic slot covers. Ensure they are locked into position by pushing it down into place. Attach armrest fabric cover by: To attach third plastic peg • Sliding the fabric cover towards the bumper bar and press in to attach the second and third plastic pegs (located underneath the fabric cover).
- Page 15 How to care for your Childcare stroller Cleaning To ensure the long-lasting use of your stroller, dry it with a soft absorbent cloth after use in rainy weather. Use a damp cloth to clean the frame. Do not use abrasive cleaners. After using your stroller on the beach, clean the frame and wheels thoroughly with water to remove the sand and salt.
- Page 16 Distributed in Australia by CNP Brands, 20 Calarco Drive, VIC, 3030 Customer Service 1300 667 137 www.cnpbrands.com.au Distributed in New Zealand by Wainhouse Distribution, 2-6 Argyle St, Morningside, PO Box 41-014, St Lukes, Auckland, New Zealand Customer Service: 0800 567 5000 helpline@wainhousedist.co.nz...