TABLE OF CONTENTS TABLE OF CONTENTS SAFETY INFORMATION FOR WIRELESS HANDHELD PHONES ... 6 PRECAUTIONS ... 9 SYSTEM CONFIGURATION ... 10 WRIST STRAP ATTACHMENT ... 11 BATTERY INSTALLATION AND RECHARGING ... 12 To Attach the Battery Pack ... 12 To Detach the Battery Pack ... 12 To Recharge Battery ...
Page 3
PHONEBOOK OPERATION ... 23 Phonebook Entry ... 23 To Store a Number without Name ... 23 Overwrite Warning ... 24 Auto Hyphenation ... 24 Manual Hyphenation ... 25 Automatic Storing into Phonebook ... 25 To Store Dual Numbers in Phonebook ... 26 To Store a Name with the Phone Number ...
Page 4
Volume and Tone Controls ... 54 Alert Tone Volume Control (F31) ... 54 Ring Type Selection (F32) ... 54 Key Tone Volume Control (F33) ... 54 To Mute a Phone Conversation (F34) ... 55 Sending DTMF (F35) ... 55 Setting Tones (F36) ... 55 Key Tone Length (F36-1) ...
Page 5
Congratulations... You have just purchased one of the most advanced cellular telephones in the market today. Your new Audiovox portable telephone is a dual mode cellular telephone operating in both the standard analog and the CDMA “digital” modes. CDMA technology is a superior digital technology that...
SAFETY INFORMATION FOR SAFETY INFORMATION FOR WIRELESS HANDHELD PHONES WIRELESS HANDHELD PHONES Read this information before using your handheld portable Cellular Telephone. EXPOSURE TO RADIO FREQUENCY SIGNALS Your wireless handheld portable telephone is a low power radio transmitter and receiver. When it is ON, it receives and also sends out radio frequency (RF) sig- nals.
Page 7
Tips on Efficient Operation: For your phone to operate most efficiently: • Extend your antenna fully. • Do not touch the antenna unnecessarily when the phone is in use. Contact with the antenna affects call quality and may cause the phone to operate at a higher power level than otherwise needed.
Page 8
Other Medical Devices If you use any other personal medical device, consult the manufacturer of your device to determine if they are ad- equately shielded from external RF energy. Your physician may be able to assist you in obtaining this information. Vehicles RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles.
4. DO NOT use unauthorized accessories. 5. DO NOT disassemble the phone or its ac- cessories;If service or repair is required, return the unit to an authorized Audiovox cellular service center. If the unit is disas- sembled, the risk of electric shock or fire may result.
SYSTEM CONFIGURATION SYSTEM CONFIGURATION System configuration and the equipment list are as shown below. Retractable Whip Antenna Handheld Portable Telephone Battery Pack Desktop Holder List of Equipment Name of the Equipment Handheld Portable Telephone Slim Lithium Ion Battery Pack (BTR-4000) Desktop Holder (DTH-4000) AC Adapter (CNR-4000) Wrist Strap...
WRIST STRAP ATTACHMENT WRIST STRAP ATTACHMENT Attach the wrist strap to the phone through the strap hole as shown below Then put the long loop through the smaller loop as shown below...
Lift up to remove the Battery Pack from the phone gently. Release Latch To Recharge Battery Your CDM-4000 has a built-in charger function. To re- charge the Battery Pack, always install the Battery Pack to the Phone. 1. Attach the Battery Pack to the Phone.
Page 13
4. Then the recharging starts. The display indicates “now charging” with animation. You can see a battery level indicator scroll- ing at the upper-right of the display. 5. For complete recharging, it is recommended that the phone is turned off dur- ing recharging.
FUNCTIONS FUNCTIONS External View Retractable Whip Antenna Power Indicator Receiving Signal Strength Indicator Digital Mode Indicator IN USE Indicator Roaming Indicator IN USE Message Indicator Battery Level Indicator Send Key Store Key Message Access Key Rcl F OneTouch Emergency Key Digit Keys PQRS OPER...
Function of Keys Digit Keys To enter Telephone Numbers, Names or special characters ( or ). is also used for OneTouch PQRS WXYZ Emergency feature. OPER Function Keys Rcl F SEND key. To originate or receive a Call. END key. To terminate a Call and to turn the phone ON/OFF.
GETTING STARTED GETTING STARTED Turning the Phone On/Off Press for more than one second. All the indicators and the digit display will light momentarily, and a tone will be heard. The indicator will stay while the phone is turned on. To turn the phone off, press for more than one sec- ond.
BASIC OPERATION BASIC OPERATION Placing Calls To Place a Call 1. Enter the phone number. (A maximum of 32 digits will be displayed.) 2. Press The IN USE indicator will light. • To Correct a Number Press to clear the last digit. Press and hold to erase all the digits entered.
Speed Dialing If you know the phonebook address of the telephone number that you want to call, you may place a call with- out using 1. Enter the one or two digits of your Phonebook ad- dress (1 ~ 9 or 10 ~ 99). 2.
OneTouch Emergency Call This feature permits you to dial an emergency number by a single key stroke, even in the “Phone Lock” or “Restrict” mode. This feature can be turned off to pre- vent unintentional calls to the emergency number. See To Turn On/Off OneTouch Emergency Call Fea- ture (F63) on page 65.
Depressing any key will clear the number of calls indi- cated in the display. Ringing Tone with Melody The CDM-4000 offers you 15 styles of ringer tones and melodies for alerting incoming calls. Ringer volume can also be adjusted. See Ring Type Selection (F32) and Alert Tone Volume Control (F31) on page 54 for setting.
For more information, see End to End Signaling on page 22. Automatic Talk Timer The talk time of the current call will be automatically displayed. Example: Call Waiting Your service provider may provide Call Waiting service. When you are on a call, you may hear beep tone alert- ing you of another incoming call.
End to End Signaling To utilize certain phone services, such as accessing an alternate long distance network, signaling a pager or banking by phone etc., Touch Tone™ signaling is re- quired. The following features will make it easy to send frequently used Touch Tone™...
PHONEBOOK OPERATION PHONEBOOK OPERATION Your phone has an Enhanced Phonebook with 99 dual- number memory addresses. At each address, you can store up to two telephone numbers under one name. This feature allows you to store, under one name, a person’s home and office number, office and mobile number, etc.
Overwrite Warning When you attempt to store a number in an address where another number has been already stored, you will have “OVERWRITE” warning. Example: To store the number 9 8 7 6 5 4 3 2 1 0 in the address 07, where another num- ber 1 2 3 4 5 6 7 8 9 0 is already stored.
Manual Hyphenation You can manually insert a hyphen at any place when you enter a telephone number. The maximum number is 32 digits long including hyphens. Example: To insert a hyphen in the number 1 2 3 4 5 6 7 to display it as 123-4567. 1.
4. Press To Store Dual Numbers in Phonebook You can store Dual Numbers with Dual Mark “ \ ” up to 32 digits for all the address 01 to 99 in the phonebook. Up to 32 digits Primary Number \ Secondary Number To store two telephone numbers in one phonebook ad- dress, enter the first number, select the Dual Mark “...
To Store a Name with the Phone Number To use this procedure, you will need to refer to “Alpha Mode” below. 1. Enter the phone number. 2. Press to select the Alpha Mode. 3. Enter the name. 4. Press , then enter the memory address (01 through 99) to store the number with the name into memory.
Page 28
3. Press digit key repeatedly to display the letter that you want. The following table shows which char- acter is assigned with each digit key. For example, to enter the letter “D”, press letter “F”, press 3 times. Assigned Alpha Characters 1 press 2 press 3 press...
To Store a Ring Type with the Phone Number (Distinctive Ringing) You can choose one of 15 ring types for each phonebook address. With this feature, you will be able to distin- guish who is calling by hearing the ringing tone. The ring type is selected while storing the number when the word “OPTION”...
Recall Menu Press key. The following “RECALL” menu will prompt you to recall the number from the memory. • “ADDRESS” : Phonebook Address Mode • “SEARCH” : Phonebook Sort Scroll Mode or Phonebook Key Word Search Mode • “HISTORY” : Call History Mode Recall Menu Tree Main Menu...
Phonebook Recall To recall the numbers stored in your phonebook, you have three methods: Address Mode, Sort Scroll Mode and Key Word Search Mode. Phonebook Address Mode This mode is useful in finding a phone number by re- calling a specific address or by scrolling the Phonebook. 1.
Phonebook Key Word Search Mode This mode searches and displays the character string of Alpha Tags stored in the Phonebook. Any part of the Alpha Tag can be used for the search. Example: To search the character string AN stored in the Phonebook.
To Dial Dual Numbers After the number is recalled in the display, it can be easily called by pressing • To dial the primary number, just press • To dial the secondary number, press Primary Number Secondary Number To Review Long Numbers This feature allows you to review all the digits of very long numbers or numbers stored with Alpha Tags.
Phonebook Edit This section guides you how to modify, move, change priority and erase the phonebook contents. To Modify Numbers and Names You can modify any of the phonebook contents you have stored, including Phone Numbers, Names, Ring Type, Secret and Address. To Modify Phone Numbers Recall the number from the phonebook.
5. Press The Dual Mark “ \ ” is in- serted. 6. Enter WXYZ PQRS OPER 7. Press 8. Press The original number is dis- played momentarily. 9. Two seconds later. 10.Press to store in the original address. To Move Numbers and Names You can move the phonebook contents to a new ad- dress.
To Change Priority of Dual Numbers You can interchange the primary and the secondary numbers in a phonebook address. The submenu “PRI.CHANGE” will only be available when two tele- phone numbers are stored in that address. Example: 1. Recall the number. Primary Number Secondary Number 2.
Secret Memory To Store a Secret Number This feature permits you to store a phone number that you want to keep secret in your phonebook. The secret number can be accessed only by entering the security code (see page 49). Example: To store the phone number 1 2 3 4 5 6 7 8 9 0 in address 30 as a secret number.
2. Press 3. Enter the four-digit secu- rity code and press Link Dialing This feature permits you to link groups of numbers to be sent in sequence. The linked numbers can be stored in memory. When dialed, the first group of numbers will be sent in digital signaling, and the rest of the numbers will be sent in Touch Tone™...
Example: To link 3 numbers and store in Address 35. 1. Enter PQRS PQRS WXYZ 2. Press 3. Press 4. Enter 5. Press 6. Press 7. Enter PQRS WXYZ OPER 8. Press Note: While entering a linked number, you may review all the parts of that number, even those already entered.
Call History This feature recalls outgoing Call History and incoming Caller ID numbers. This is convenient for redialing re- cently called numbers or for returning missed calls by using the stored Caller ID. (See Caller ID with Name on page 19.) Call History Memories Memory Description...
2. Scroll with to review other numbers. 3. You can place a call by simply pressing When duplicate numbers are called, only the latest call is stored in the outgoing call history memory. To Review Incoming Call History Example: To recall a received Caller ID from Memory Stack.
To Save a Number to Phonebook The numbers of Call History and Scratch Pad Memory can be stored in your phonebook. You can add a name in the same way as “MODIFY”. See To Modify Num- bers and Names on page 34. Example: To save a received Caller ID to Phone- book.
MESSAGING FEATURES MESSAGING FEATURES Your CDM-4000/CDM-4000XL Audiovox Cellular Tele- phone has been engineered to operate with the latest technology that will allow you to enjoy the benefit of Voice Mail Notification and Text Messages. Please note that operation of these features depends on the Cellular Sys- tem and therefore may not be available in all areas.
Voice Mail Notification with Mail Retrieval Service (MRS) 1. The phone sounds a short beep tone. 2. Press to answer the incoming call, your phone will be connected to your Voice Message Service so that you may retrieve your messages. 3.
To Store the Voice Mail Access Number Please see To Store Linked Numbers in Phonebook on page 38, and follow the steps 1 ~ 3 to make a set of linked numbers. Press digits of linked numbers can be stored including link mark “...
To Review a Text Message Text messages are stored in the address 01 to 30 in the memory stack. The address 01 has the last message. Every message moves to the next address when a new message is stored. Example: To display a Text Message stored in the Memory Stack.
FUNCTION MENU FUNCTION MENU To Access Function Menu Various phone settings can be changed through Func- tion Menu to customize your phone’s functions to fit your convenience. See Function Menu Tree in the follow- ing page. You can reach the Function you want to ac- cess in two ways;...
Function Menu Tree Main Menu Submenu 1: LOCK 1: KEY LOCK (F11) 2: LOCK (F12) 3: AUTO LOCK (F13) 4: LOCK CODE (F14) 2: DISPLAY 1: MY NUMBER (F21) 2: BACKLIGHT (F22) 3: HYPHEN (F23) 4: SMS LINES (F24) 5: CONTRAST (F25) 6: VERSION (F26) 7: LAST SID...
Lock Features Security Code and Unlock Code Your phone is equipped with the Security Code and the Unlock Code to access various security features. You may change the preset codes for added protection. Code Preset Description Security 1234 To access Secret Number, to set Call Code Restriction, etc.
Phone Lock (F12) This mode is useful to prevent unauthorized use of the phone. With this feature on, the following functions are still available. • Incoming calls can be answered with • Any Key Answering • Programmed Emergency Call • OneTouch Emergency Call •...
3. The current unlock code will be displayed. 4. Enter a new four-digit unlock code and press Display Features Own Telephone Number Display (F21) This feature enables you to display your own telephone number and the ID number (SID) of your “Home” Cellu- lar System.
Backlight Control (In-Use) (F22-2) For ease of operation, you may select to have the back- light always on while you are engaged in a conversation. When this feature is set to the “ALWAYS ON” mode, the backlight is turned on as long as the call is connected. 1.
Software Version Review (F26) This feature permits you to review the software version which is installed in your phone. 1. Press 2. Press to exit. Last Rescan SID Indicator (F27) This menu item permits you to view the System Identi- fication number (SID), which your phone is currently using.
Volume and Tone Controls Alert Tone Volume Control (F31) 1. Press 2. Keep pressing sired sound level, or “silent” mode. Note: In “silent” alert mode, alert tone is not given for an incoming call. However, if Automatic Answer- ing feature is ON, alert tone is given with the lowest available volume.
To Mute a Phone Conversation (F34) You can mute your conversation at any time during a call. 1. Press 2. Then the “Mute” indicator is displayed. The transmit audio will be muted but the receive audio will still be heard from the receiver. 3.
Single Alert Beep Tone (F36-2) This feature is used to signal an incoming call with only a single beep. This feature can only be used with the “silent” alert mode. See Alert Tone Volume Control (F31) on page 54. 1. Press 2.
Service Mode Alert (F36-6) With this feature on, an audible tone alerts you when the service mode changes from Digital to Analog, or vice versa. 1. Press 2. You can turn this feature on/off by 3. Press to set. Voice Privacy Alert (F36-7) This feature audibly alerts you when the voice privacy service is provided, and also when the service is can- celed.
Call Timers To help you manage your calls, your phone is equipped with several Call Timers. Last Call Timer (F41-1) 1. Press The talk time of the last call will be displayed. 2. Press to exit. Outgoing Call Timer (F41-2) 1.
System Features A/B System Selection (F51) This feature permits you to select which Cellular sys- tem (A or B) your phone uses. When you turn the phone on, it remembers the last A/B setting and will scan the radio channels based on that setting. Leave this setting as it has been preprogrammed un- less you have a reason to alter the system selection.
In areas where your Carrier has Roaming agreements, your phone will display a steady “ display indicates a flashing “ ”, you are in a cellular system which is not associated with your Carrier (you can still make or receive calls). If your display indicates “(No Service)”, you may have to change your A/B System Selection or NAM Selection in order to obtain service.
System Settings (F54) This is a group of several functions for settings related to the system. 1. Press The Branch Menu is dis- played. NAM Name Display (F54-1) You can program a greeting or a name of a maximum 10 to 12 characters in the second line of your LCD dis- play.
Enhanced Voice Privacy Mode. Anti Fraud Security Features Your new Audiovox Cellular telephone has been engi- neered with the latest technology to help protect from the fraudulent use of your cellular telephone number.
To Place a Call with the Manual PIN Entry 1. Enter the number you are calling, or recall the number from a specific memory location. 2. Press . Your call will be processed. Listen for a double beep, which will prompt you to send your PIN.
To Program or Change your Automatic PIN (F54-6) 1. Press 2. Enter the four-digit secu- rity code and press 3. Enter your new PIN Code. Press Security Features Call Restriction (F61) This feature permits you to impose various kinds of re- strictions on outgoing calls.
To Change Emergency Numbers (F62) You can program your own emergency numbers. Up to 3 numbers of maximum 32 digits can be stored. Memory Location Preset Emergency Number 1. Press 2. Enter the four-digit secu- rity code and press 3. Press to select the emergency num- ber memory location (1, 2 or 3) that you want to change or program, and press...
Reset Functions (F65) This is a group of several functions for Function/Memory Reset. 1. Press 2. Enter the four-digit secu- rity code and press Then the Branch Menu is displayed. Call Timer Reset (F65-1) This feature resets all the following three Call Timers; Last Call Timer, Outgoing Call Timer and All Calls Timer.
Text Message & Voice Mail All Clear (F65-4) This feature clears all Text Messages and the Voice Mail number. 1. Press 2. Enter the four-digit security code and press 3. Press 4. Press to clear the message. Function Reset (F65-5) This feature permits you to reset the User-Program- mable functions to their initial settings.
Function Reset Status The following functions will return to the initial settings after Function Reset. Functions Automatic Lock (F13) Backlight Control Portable Use (Standby) (F22-1) With Car Kit Backlight Control (In-Use) (F22-2) Auto Hyphenation (F23) Text Lines Selection (F24) Contrast Control (F25) Earpiece Volume Control Alert Tone Volume Control (F31) Ring Type Selection (F32)
(It is also unlawful to take over a line by stating falsely that it is needed for an emergency). The CDM-4000/CDM-4000XL is using one or more of the following US patents licensed by QUALCOMM Incorporated:...
12 MONTH LIMITED WARRANTY AUDIOVOX COMMUNICATIONS CORP. (the Com- pany), warrants to the original retail purchaser of this Audiovox Handheld Portable Cellular Tele- phone, that should this product or any part thereof (except the items listed below), under normal use...
Page 74
IN U.S.A.: AUDIOVOX COMMUNICATIONS CORP. 555 Wireless Blvd., Hauppauge, New York 11788 (516) 233-3300 IN CANADA: AUDIOVOX CANADA LTD. 405 Britannia Road East, Mississauga, Ontario L4Z3E6 (905) 712-9299...
Quick Reference Basic Operation Turn On/Off (more than one second) Place a Call Phone Number, Terminate a Call Receive a Call Any Key (except Clear Last Digit (less than 0.5 sec.) Clear All Digits (more than 0.5 sec.) Earpiece Volume Convenience Features Store Number in Phonebook , Phone Number,...
Page 76
Functions Mute/Unmute Keypad Lock Lock the Phone Automatic Lock Display Own Phone Number & SID Backlight Control Last Call Time Display Outgoing Call Time Display All Calls Time Display Automatic Answering A/B System Selection Force Analog Call Functions Mute/Unmute Keypad Lock Lock the Phone Automatic Lock Display Own Phone Number &...
Many companies are making look-alike acces- sories and in some cases, promoting that their product is equal to or better than the Audiovox product. Be careful. Some of these products may not be compatible for use with your Audiovox product and may damage the unit or cause it to malfunction.