Download
Share
Print this page
  1. Manuals
  2. Brands
  3. THUNDER TIGER Manuals
  4. Toy
  5. YAK 54
  6. Assembly manual

THUNDER TIGER YAK 54 Assembly Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
Enlarged version
MEMO
THUNDER TIGER CORP.
www.thundertiger.com
16
Assembly Manual
No. 4349
Specification:
Wing Span: 45 (1143mm)
Length: 45.5
(1160mm)
Weight: 2.3lb.(1000~1100g)
2
Wing Area: 382 sq.in. (24.66 dm )
This kit is guaranteed to be free from defects in material and workmanship at the date of purchase.
It does not cover any damage caused by use or modification. The warranty does not extend beyond
the product itself and is limited only to the original cost of the kit. By the act of building this user-
assembled kit, the user accepts all resulting in liability for damage caused by the final product. If the
buyer is not prepared to accept this liability, it can be returned new and unused to the place of
purchase for a refund. Neither your dealer nor Thunder Tiger Distributors, can accept kits for return if
construction has begun.
Notice: Adult Super Vision Required
This is not a toy. Assembly and flying of this product requires adult supervision.
Read through this book completely and become familiar with the assembly and flight of this airplane.
Inspect all parts for completeness and damage. Browse www. thundertiger. com for customer service
if you encounter any problems.
Warranty
1
JE9000

Advertisement

loading

Related Manuals for THUNDER TIGER YAK 54

Summary of Contents for THUNDER TIGER YAK 54

  • Page 1 If the buyer is not prepared to accept this liability, it can be returned new and unused to the place of purchase for a refund. Neither your dealer nor Thunder Tiger Distributors, can accept kits for return if construction has begun.

  • Page 2: Table Of Contents

    OTHER ITEMS REQUIRED FOR ASSEMBLY Thank you for your purchase of the Thunder Tiger 3D YAK 54 EP. You can make this proven 3D fun flyer A checklist is provided as below which will make shopping for these items easier.

  • Page 3: Parts Drawings

    PARTS DRAWINGS PARTS DRAWINGS Open the box and check that you have all the parts as shown below. AS9127-03 Fuselage AS913 0-03 Cowling AS913 1-03Canopy AS9127-04 AS9130-04 AS913 1-04 M3x12 mm (4) Velcro (1) Tie Belt (1) Canopy (1) Cowling(1) Fuselage (1) 2.3x8mm Wood Screw (4) Frame (1)

  • Page 4: Wing

    TAIL WING 1. Locate the aileron servo well at the bottom wing. 4.CA the four hinges on aileron. Make sure the hinges 7. Secure the control horn with CA or epoxy, make 10. Remove the stab and fin, cut away the covering Use hobby knife to cut an “X”...

  • Page 5: Tail

    MOTOR TAIL 22. Same way to install the rudder control horn in place as shown. 19. Install the elevator servo as shown at the left side 13. Apply epoxy in the elevator torque rod holes then 16. Trial fit the rudder in place, make sure it works of fuselage.

  • Page 6: Tail

    RADIO COWL 26. Install the carbon landing gear in place with M3x10 32. Thread the antenna through the fuselage and exit 35. Install the Canopy assembly in place. It should 29. Secure the battery with the tie belt as shown in the socket screws, M3 washers and M3 locknuts.

  • Page 7: Motor

    Your done, may you have many successful flights filled with fun and lots of 3D maneuvers. It is important to balance the plane to get correct C.G. before you fly. Thank you for purchasing this plane from Thunder Tiger and we look forward to providing you with other Balance Point as indicated in each diagram.

  • Page 8: Radio

    Exponetial Simulator practice might be perfect yet suggest to do To make your 3D flight successful, the most important is to set up your radio properly and fine-tune the some actual flying as the supplemental so it will not exponential. We would suggest that could show the go too far from the real thing as there are many things exponential graph as the illustration.