Subscribe to Our Youtube Channel
Related Manuals for Kranzle 2+2
Summary of Contents for Kranzle 2+2
- Page 1 O p e r a t i n g m a n u a l Power sweeper 2+2 Read and conform safety instructions before use! - GB -...
-
Page 2: Dear Customer
Description Dear Customer Congratulations on your new sweeper! For your convenience, a description of the machine is provided on the following pages. Technical specifications Method of operation: 2- roller hasp principle Working width: 800 mm Weight: 17 kg Container capacity: 40 litres Brushes: heavy duty polypropylene Seeping rate: approx. 3000 m²/ hr The machine is fully recyclable. It is made completely of polypropylene „PP“ and natural rubber. The brush rollers are made of wood. The machine is PVC - FREE and one hundred percent.... made by The sweeper is designed for use on a level surface. With the side brushes pressed, you can push the machine easily over the surface to be cleanend. This should be done done at normal walking speed (approx 3 km/ hr). The seeping rate depends on the speed the brush rollers rotate, and this in turn depends on the speed the machine is pushed. The pushing force required is between 3 and 3,5 kg, depending on the surface, If you wish to move the machine for longer distances without sweeping, pull it bachwards so that the sweeping function is disabled by the built-in free-wheel feature. - Page 3 Assembly for side brushes and push handle Place the machine on the ground .. and lift it out Pull the cover of the interior. Pull the push handle upwards Grip the collector handle..and place the accessories on the ground...
- Page 4 Assembly of side brushes and push handle Loosen the four plastic screws (4) on the underside of the dust spoiler (3) and place Now press the safety caps from above,making sure the screws with the plain washer (5) on the that they are attached to the correct sides (engraved ground. right and left). Press the spoiler from the top onto the housing. Now turn the screws with the plain washer from below through the holes in the housing into the spoiler.Now tighten the screws. Fold back the handle on the machine. Now put the sweeper upside down on the ground and, remove Fix the push bar into the work position in the screw from the brass axle of the inlet brush. hole (A) using the star screws provided (a). First place washer no. 72 on side brush no. 74 above the ball bearing and place both on bearing bolt A. Tighten the screw with safety washers no. 76 and no. 77 into the bolt.
- Page 5 Description To empty the container When the dirt container is full, take hold of the handle and simply pull it upwards. The contents can then be disposed of accordingly.Replace the container in the reverse order. Loading brushes Unloading the brushes When the inlet Press the two brushes are no brush heads to put longer required, the inlet brushes press the release into the work lever briefly and the position. brushes will engage The height of the in the rest position. side brushes can be adjusted on both sides. Fig. 1 Fig. 2 Storage To release the constant pressure from the side brushes, it is recommended after each use to move the machine approx. 5 cm backwards, in order torelieve the bristles and to raise the side brushes using the lever (c) (fig. 2). This prevents the bristles from deforming and diminishing their cleaning efficiency. To release strain on the bristles of the sweeping rollers and to save space in storage, you can unscrew the star screws (a) on the left and right of the push bar, fold the bar forwards into the parking position and replace the screw in hole B. The machine can now be stored vertically and requires less space. The container does not need to be emptied to do this.
- Page 6 Servicing No work need to be done on the machine because it does not require servicing. Ho- wever, you should check after each use that there are no threads, wire or strips of material round the roller. If there are any, they should be removed immediately since it will otherwise be impossible for the machine to oerate properly. In the event og heavy soiling, grasp the dust filters (left and right) behind the cassette using the screw driver, lift them out comple- tely and either clean the filter or replace it. Filter paper: Art.-no. 50.130 Repair set: filter cassette complete: Art.-no. 50.190 Warranty This warranty covers material and/or workmanship related defects only and does not extend to ordinary wear. Machine must be operated according to enclosed operating instructions which are part of present warranty conditions.
- Page 7 Servicing When the rollers are worn, the sweeper can be placed approx. 1 - 1,5 mm lower by remo- ving the two washers no. 13 (see page 10). Important: One washer no. 13 must always be kept under the screwhole to avoid damaging to the plastic frame Easy replacement of brush rollers: 1) Put the machine upright on the joints of the folded-in push bar and the frame. 2) Turn the brush roller until the two screws no. 34 on the left and right side respectively are visible (see page 12) and remove these 4 screws. 3) Turn the brush rollers another half-turn and remove them by pulling them out. 4) Fit the new rollers in the reverse order.
-
Page 8: Complete Machine
Complete machine... - Page 9 Kränzle Power Sweeper 2 + 2 Spare parts list Power Sweeper 2 + 2 Complete machine Pos. Description Qty. Part no. Gehäuse 50.102 Schmutzbehälter 50.101 Rechen 50.151 Abdeckung vorn 50.150 Unterlegscheibe 5,3 50.152 Abweisleiste 50.105 Schraube 5,0 x 25 41.414 1 7.1 Kunststoffschraube 5,0 x 20 43.018 Gummilappen hinten mit Klemmleiste 50.171 Schmutzführung 50.163 Schraube 3,5 x 9,5...
- Page 10 Left wheel and sweep rollers...
- Page 11 Kränzle Power Sweeper 2 + 2 Spare parts list Power Sweeper 2 + 2 Left wheel and sweep rollers Pos. Description Qty. Part no. Bürstenwalze vorn 50.119 Bürstenwalze hinten 50.120 Bürstenmitname 50.121 Holzschraube 3,5 x 17 50.165 Sicherungsscheibe 10 50.133 Scheibe 13 DIN 433 50.184 Zahnrad z=14 50.115 Abstandshülse 20,5 mm 50.155 2 Mitnahmebolzen (links hinten) 50.126 Rillenkugellager 12 / 28 / 8...
-
Page 12: Right Wheel
Right wheel... - Page 13 Kränzle Power Sweeper 2 + 2 Spare parts list Power Sweeper 2 + 2 Right wheel Pos. Description Qty. Part no. Bürstenmitname 50.121 Holzschraube 3,5 x 17 50.165 Sicherungsscheibe 10 50.133 Scheibe 13 DIN 433 50.184 MS-Scheibe 12 x 24 x 2,5 50.139 Abstandshülse 20,5 mm 50.155 2 Rillenkugellager 12 / 28 / 8 50.156 Elastic-Stop-Mutter M8 x 1 14.152 Scheibe 50.113 Mitnahme 50.111 Rad mit Lagerung 50.191...
- Page 14 Left side brush...
- Page 15 Kränzle Power Sweeper 2 + 2 Spare parts list Power Sweeper 2 + 2 Left side brush Pos. Description Qty. Part no. Schraube 5,0 x 25 41.414 1 Sicherungsscheibe 10 50.133 Scheibe 13 DIN 433 50.184 Abstandshülse 14,5 mm 50.155 1 Rillenkugellager 12 / 28 / 8 50.156 MS-Scheibe 12 x 24 x 2,5 50.139 Rastknopf 50.132 Fußraster 50.131 Druckfeder (klein) 50.158 Sicherungsring 12 DIN 471 50.137 Rückstellfeder (groß)
- Page 16 Right side brush...
- Page 17 Kränzle Power Sweeper 2 + 2 Spare parts list Power Sweeper 2 + 2 Right side brush Pos. Description Qty. Part no. Schraube 5,0 x 25 41.414 1 Sicherungsscheibe 10 50.133 Scheibe 13 DIN 433 50.184 Abstandshülse 14,5 mm 50.155 1 Rillenkugellager 12 / 28 / 8 50.156 MS-Scheibe 12 x 24 x 2,5 50.139 Rastknopf 50.132 Fußraster 50.131 Druckfeder (klein) 50.158 Sicherungsring 12 DIN 471 50.137 Rückstellfeder (groß)
- Page 18 Notes...
- Page 19 Notes...
- Page 20 Reprint only allowed with the authorization of As date of 10.09.2013...
Need help?
Do you have a question about the 2+2 and is the answer not in the manual?
Questions and answers