Timer Instructions - Coralife LED BioCube Instructions Manual

Lighting Startup Operation
1. Plug the power supply into an acceptable
outlet or power source. Be sure to incorporate
a "drip loop" to prevent water droplets from
running down the cord and into the outlet should
any water get onto the cord.
2. Turn the hood on and follow instructions below
to program the timer.
Timer Programming Instructions
Selecting a Program:
1. Press MENU and then use the UP or DOWN
arrows to search for your desired program.
• ALL = All LEDs will turn on (at full power)
• LC1 = Only Daytime LEDs will turn on
• LC2 = Only Sunrise/Sunset LEDs will turn on
(They will start at low power and increase
incrementally over 30 minutes)
• LC3 = Only Moon Glow LEDs will turn on
(They will start at low power and increase
incrementally over 60 minutes)
• CLO = Set the timer for all LEDs (You must
press MENU again to set the clock and
program the timer)
• SHO = Demo mode will turn on
Demo (SHO) Mode:
Perfect for showcasing your new LED Lighting, this
mode cycles through a 24-hour lighting sequence in
just 3 minutes.
• Sunrise: 30 sec • Moonrise: 30 sec
• Day Time: 60 sec • Moonset: 30 sec
• Sunset: 30 sec • Night Time: 60 sec
Please Note: Except under CLO mode, pressing MENU
again or waiting 30 seconds without pressing anything
will exit back to clock display. Pressing MENU in CLO
mode will enter clock and timer program mode.
To Set Time of Day (CLO Mode):
1. Choose 12 or 24 Hour Mode:
a. '12H' will appear on the display. Press the
UP arrow key to change to '24H' clock mode.
Pressing the DOWN arrow key will change
the mode back to '12H'.
2. Press MENU to move to the next step.
3. ' ' will appear on the screen to indicate clock
setting function. If 12H mode was selected, clock
will display '12:00am' with the '12' blinking. If
24H mode was selected, will display '0:00am'
with the '0' blinking.
4. Press arrow keys UP or DOWN to set the hour.
5. Press MENU to move to minutes. Use the arrow
keys UP or DOWN to set the minutes.
6. When time setting is complete, press MENU to
move to the next step – Programming Channel 1.
Programming Channel 1 - Daylight LEDs
'1' and 'On' will appear on the screen to indicate
timer setting for channel 1.
7. Press arrow keys UP or DOWN to set the hour.

TIMER INSTRUCTIONS

7
8. Press MENU to move to minutes. Use the arrow
keys UP or DOWN to set the minutes.
9. Press MENU to move to 'off' time for channel 1.
Repeat steps 7 and 8.
10. When Channel 1 programming is complete press
MENU to move to the next step – Programming
Channel 2.
Programming Channel 2 - Color Enhancing
LEDs (Automatic Sunrise/Sunset Function)
'2' and 'On' will appear on the screen to indicate
timer setting for channel 2.
11. Press arrow keys UP or DOWN to set the hour.
12. Press MENU to move to minutes. Press arrow
keys UP or DOWN to set the minutes.
13. Press MENU to move to 'off' time for channel 2.
Repeat steps 11 and 12.
14. When Channel 2 programming is complete press
MENU to move to the next step – Programming
Channel 3.
When setting Channel 2 the start time and stop time
will indicate when Sunrise mode will initially light up
and when Sunset mode will initially dim down. LEDs
will gradually ramp up or dim down for 30 minutes
from the set time.
Programming Channel 3 - Moon Glow LEDs
(Automatic Moonrise/Moonset Function)
'3' and 'On' will appear on the screen to indicate
timer setting for channel 3.
15. Press arrow keys UP or DOWN to set the hour.
16. Press MENU to move to minutes. Press arrow
keys UP or DOWN to set the minutes.
17. Press MENU to move to 'off' time for channel 3.
Repeat steps 15 and 16.
18. When Channel 3 programming is complete press
MENU to Exit programming mode and return to
the clock time display.
When setting Channel 3 the start time and stop time
will indicate when Moonrise mode will initially light up
and when Moonset mode will initially dim down. LEDs
will gradually ramp up or dim down for 60 minutes
from the set time.
Timer Function Notes:
• If at any time in programming the timer there
is no activity for 30 seconds the timer will
immediately return back to clock time display.
• If at any time the power is turned off the
following will occur when the hood is
reactivated:
Setting will default to the programmed
o
settings (CLO Mode)
If in daytime – the Sunrise feature will
o
start automatically. Maximum brightness
will occur after 30 minutes.
If in nighttime – the Moonrise feature will
o
start automatically. Maximum brightness
will occur after 60 minutes.