Table of Contents
Advertisement
Quick Links
CISEYE
™
Network Camera with Pan/Tilt/Zoom
Quick Installation Guide
This guide describes the basic functions of
Network Camera with Pan/Tilt/Zoom.
All detailed information is described in the user's manual.
CISEYE SECURITY TECHNOLOGIES SDN. BHD.
(Co. No. 691660-P)
49, Jalan 1/119, Taman Bukit Hijau, Cheras 56000, Kuala Lumpur, Malaysia.
Tel : 603-9132 9151 (9152/9153)
Fax : 603-9132 9553
Website : www.ciseye.com
Email : sales@ciseye.com
Advertisement
Table of Contents
Related Manuals for CISEYE cip300
Summary of Contents for CISEYE cip300
-
Page 1: Quick Installation Guide
This guide describes the basic functions of Network Camera with Pan/Tilt/Zoom. All detailed information is described in the user’s manual. CISEYE SECURITY TECHNOLOGIES SDN. BHD. (Co. No. 691660-P) 49, Jalan 1/119, Taman Bukit Hijau, Cheras 56000, Kuala Lumpur, Malaysia. Tel : 603-9132 9151 (9152/9153) Fax : 603-9132 9553 Website : www.ciseye.com... -
Page 2: Warning Before Install
Warning Before Install • Power off the Network Camera as soon as it is found smoking or smelt unusual. Contact your distributor when such cases happen. • Keep the Network Camera away from the water. If the Network Camera is wet, power off immediately. - Page 3 • Do not touch the Network Camera when it’s lightening. • Do not disassemble the Network Camera. • Do not drop the Network Camera. • Do not insert any object into the Network Camera, such as needles. • Do not manually pan and tilt the Network Camera when the power is on.
-
Page 4: Check Package Contents
1. Check Package Contents • The Network Camera (Wire or Wireless model) • Power adapter • Camera stand • A/V cable • Antennas (for wireless model only) • Software CD • Remote controller... -
Page 5: Physical Description
2. Physical Description Front panel Antennas for wireless model only Lens Microphone Status LEDs Rear panel A/V out EXT I/O External Mic.. Ethernet 10/100 RJ45 socket Power cord socket Note the serial number from the label on the unit. This serial number is the same as the Ethernet address. For example: 0002D1455282 = 00-02-D1-45-52-82... - Page 6 3. Install Your Network Camera In Ethernet Network (Antennas for Wireless model only) 1. If you have external devices such as sensors and alarms, make connection form I/O terminal block. *Refer to your user’s manual for the I/O 2. Use Ethernet cable to make connection from Ethernet port to the hub.
-
Page 7: Assign Ip Address
4. Assign IP Address 1. Run the “Setup.exe” under the InstallationWizard directory from software CD. 2. The program will launching the installation shield. - Page 8 5. The Internet Explorer Connects To The Network Camera For setup further configuration, please check user’s manual on the software CD.
- Page 9 6. Client Settings (Windows XP/2000/Me/98SE) At the initial access to the “Connection type” page in Windows, the web browser will ask for a new plug-in installation, the plug-in being the Network Camera. This plug-in has been registered for certification and can be used to change the parameters at the client’s site.
- Page 10 3. Lower down the security level bar to “Low”, and press “Apply” 4. Refresh IE Browser, a question frame will pop-up to ask for download Active-X, press “Y es”...
- Page 11 7. Client Settings (Windows XP SP2) 1. Initial IE browser, select function item “Tools” > “Internet Options” 2. Security > Custom Level...
- Page 12 3. Security Settings Download unsigned ActiveX Controls set “Enable” and press “OK” 4. Press ?Apply? and then ?OK?
- Page 13 5. Key-in camera’s IP address and press “OK” on Information Bar 6. Click the blue bar under the Camera’s IP address in the browser, then choose “Install ActiveX Control” 7. Recover security settings. Download unsigned Active X Controls set “Disable” and press “OK”...