Table of Contents
Advertisement
Quick Links
CISEYE
™
Network Camera
Quick Installation Guide
This guide describes the basic functions of
Network Camera.
All detailed information is described in the user's manual.
CISEYE SECURITY TECHNOLOGIES SDN. BHD.
(Co. No. 691660-P)
49, Jalan 1/119, Taman Bukit Hijau, Cheras 56000, Kuala Lumpur, Malaysia.
Tel : 603-9132 9151 (9152/9153)
Fax : 603-9132 9553
Website : www.ciseye.com
Email : sales@ciseye.com
Advertisement
Table of Contents
Related Manuals for CISEYE CIP-100
Summary of Contents for CISEYE CIP-100
-
Page 1: Network Camera
This guide describes the basic functions of Network Camera. All detailed information is described in the user’s manual. CISEYE SECURITY TECHNOLOGIES SDN. BHD. (Co. No. 691660-P) 49, Jalan 1/119, Taman Bukit Hijau, Cheras 56000, Kuala Lumpur, Malaysia. Tel : 603-9132 9151 (9152/9153) Fax : 603-9132 9553 Website : www.ciseye.com... -
Page 2: Warning Before Install
Warning Before Install • Power off the Network Camera as soon as it is found smoking or smelt unusual. Contact your distributor when such cases happen. • Keep the Network Camera away from the water. If the Network Camera is wet, power off immediately. - Page 3 • Do not touch the Network Camera when it’s lightening. • Do not disassemble the Network Camera. • Do not drop the Network Camera. • Do not insert any object into the Network Camera, such as needles. (Antenna for wireless model only)
-
Page 4: Check Package Contents
1. Check Package Contents • Network Camera • Power adapter • Camera stand • Antennas (for wireless model only) • Software CD... -
Page 5: Physical Description
2. Physical Description Front panel Antenna for wireless model only Microphone Lens and manual focus ring Status LEDs Rear panel Antenna for wireless model only Note the serial number from the label on the unit. This serial number is the same as the Ethernet address. For example: 0002D1000019 = 00-02-D1-00-00-19 Reset button... - Page 6 3. Install Your Network Camera In Ethernet Network 2. Connect power cord to a power outlet (Wireless model only) 1. Use Ethernet cable to make connection from Ethernet port to the hub * Use Category 5 Cross Cable when the Network Camera is directly connected to PC...
-
Page 7: Assign Ip Address
4. Assign IP Address 1. Run the “Installer Wizard” under the Software Utility directory from software CD. 2. The program will search the servers or cameras on the same LAN. 3. After searching, the main installer Window will pop up. Click on serial Number that matches the one you just Note from 2. - Page 8 6. Setup Your Wireless Configuration For The Network Camera Wireless Model Only 1. Check the SSID currently set on your wireless access point (AP). 2. Go to Configuration > Network > WLAN Configuration. 3. Type in the SSID consistent with the setting on your AP . 4.
- Page 9 7. Client Settings (Windows XP/2000/Me/98E) At the initial access to the “Connection type” page in Windows, the web browser will ask for a new plug-in installation, the plug-in being the Network Camera. This plug-in has been registered for certification and can be used to change the parameters at the client’s site.
- Page 10 3. Lower down the security level bar to “Low”, and press “Apply” 4. Refresh IE Browser, a question frame will pop-up to ask for download Active-X, press “Y es”...
- Page 11 8. Client Settings (Windows XP SP2) 1. Initial IE browser, select function item “Tools” “Internet Options” 2. Security “Custom Level”...
- Page 12 3. Security Settings Download unsigned ActiveX Controls set “Enable” and press “OK” 4. Press ?Apply? and then ?OK?
- Page 13 5. Key-In camera’s IP address and press “OK” on Information Bar 6. Click the blue bar under the Camera’s IP address in the browser, then choose “Install ActiveX Control” 7. Recover security settings. Download unsigned Acti veX Controls set “Disable” and press “OK”...