Alarm Controls Corporation KP-400 User Manual

Alarm Controls Corporation KP-400 User Manual

Digital keypad for access control applications
Hide thumbs Also See for KP-400:

Advertisement

MODEL KP-400
VANDAL RESISTANT & WEATHERPROOF
SELF-CONTAINED DIGITAL KEYPAD
DESIGNED FOR ACCESS CONTROL APPLICATIONS
OPERATES ON 12 OR 24 VOLTS AC/DC, AUTO SENSING
FULLY PROGRAMMABLE FROM THE KEYPAD
302 STAINLESS STEEL FACEPLATE WITH TAMPER-PROOF SCREWS
BLACK POWDER COATED DIE CAST ALUMINUM BACK BOX
100 USER CODES WITH CODE LENGTHS FROM 4 TO 8 DIGITS
KEYS ARE BACKLIT FOR VISIBILITY IN DARK AREAS
DIE CAST METAL KEYS WITH AUDIBLE AND VISUAL KEY PRESS
TWO PROGRAMMABLE S.P.D.T. RELAY OUTPUTS
DOOR PROP OPEN ALARM, DOOR FORCED OPEN ALARM
BUILT-IN TAMPER SWITCH, BUILT-IN BUZZER
REQUEST TO EXIT INPUT, DURESS OUTPUT, ANTI-TAILGATING FEATURE
RED, YELLOW AND GREEN LEDS INDICATE KEYPAD STATUS
LIFETIME LIMITED WARRANTY
ALARM CONTROLS CORPORATION
DEER PARK, NEW YORK
11729

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the KP-400 and is the answer not in the manual?

Questions and answers

Summary of Contents for Alarm Controls Corporation KP-400

  • Page 1 MODEL KP-400 VANDAL RESISTANT & WEATHERPROOF SELF-CONTAINED DIGITAL KEYPAD DESIGNED FOR ACCESS CONTROL APPLICATIONS OPERATES ON 12 OR 24 VOLTS AC/DC, AUTO SENSING FULLY PROGRAMMABLE FROM THE KEYPAD 302 STAINLESS STEEL FACEPLATE WITH TAMPER-PROOF SCREWS BLACK POWDER COATED DIE CAST ALUMINUM BACK BOX...
  • Page 2: Specifications

    MODEL KP-400 DIGITAL KEYPAD FOR ACCESS CONTROL APPLICATIONS SPECIFICATIONS OPERATING VOLTAGE: 12 OR 24 VOLTS AC/DC, AUTO SENSING ACTIVE CURRENT DRAW : 100 MA. @ 12 VOLTS, 120 MA. @ 24 VOLTS IDLE CURRENT: 10 MA. MAX. @ 12 VOLTS, 22 MA. MAX. @ 24 VOLTS OUTPUT 1 CONTACT RATING: S.P.D.T., 5A.
  • Page 3: Operating Instructions

    SELF-CONTAINED DIGITAL VANDAL RESISTANT/WEATHERPROOF ACCESS CONTROL KEYPAD MODEL KP-400 OPERATING INSTRUCTIONS ALARM CONTROLS CORPORATION 19 BRANDYWINE DRIVE P.O. BOX 280 DEER PARK, NY 11729 11/09 REV. B WWW.ALARMCONTROLS.COM...
  • Page 4 The KP-400 is a self-contained vandal resistant digital keypad with field proven relia- ALARM CONTOLS CORPORATION bility that operates on 12 or 24 volts AC or DC. This dual relay output keypad is suit- able for residential, industrial and commercial installations and is compatible with all PRODUCT LINE electric locking devices.
  • Page 5 DEFINITIONS KEYPAD TERMINALS FRONT OF KEYPAD DRY CONTACTS BACKLIT Dry contacts do not have voltage connected to them. The Relay Output contacts in the KP-400 JUMPER TAMPER LEDS Keypad are dry contacts. FULL N/C CONTACT QUASI The contact is closed in the static state and open in the active state. The contact is open when the circuit is active.
  • Page 6 KEY ACT (KEY ACTIVE OUTPUT) DURESS OUTPUT THIS IS AN NPN TRANSISTOR OPEN COLLECTOR OUTPUT THAT SWITCHES TO GROUND, (-) FOR 10 SECONDS WITH EACH KEY PRESS. THIS CAN BE USED TO TURN ON A BUZZER, TURN ON LEDS OR OPERATE A LOW CURRENT RELAY. THE RATING OF THIS OUTPUT IS LIMITED TO Ic MAX.
  • Page 7: Led Indicators

    APPLICATIONS FOR THE AUXILIARY TERMINALS LED INDICATORS NORMALLY-CLOSED TAMPER SWITCH RED LED ON WHEN OUTPUT 2 IS ACTIVE YELLOW LED MONITORS POWER INPUT AND KEY PRESS, (SEE CHART BELOW) GREEN LED ON WHEN OUTPUT 1 IS ACTIVE The Tamper Switch is Normally-Closed when YELLOW LED INDICATOR AND TONES the Keypad is installed in the back box and THE YELLOW LED AND BUILT-IN BUZZER GIVE THE FOLLOWING SIGNALS AND TONES...
  • Page 8: Deleting A User Code

    6 4 9 2 DELETING A USER CODE An Inter-lock system requires two Keypads. This application example uses two KP-400 with simple cross wire connections to their Output Inhibit & Inter-lock Control Output. You must be in the Program Mode.
  • Page 9: Programming Options

    The Yellow Led will flash twice and you will hear two beeps. The Momentary Mode for Output 2 has been entered. You must be in the Program Mode. MODEL KP-400 Output 2 in Latching Mode Press the keys.
  • Page 10: Auto Or Manual

    Code Number is not required. In this mode the User Code must be the same length as the Installer Code and the code length can be from four to eight digits. MODEL KP-400 To program the Keypad for Auto Entry press the...

Table of Contents