Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Schlumberger Reflex USB
Summary of Contents for Schlumberger Reflex USB
- Page 1 Title Page Reflex USB Reader Installation Guide...
- Page 2 Copyrights and Trademarks Trademarks Schlumberger, Cryptoflex, Cyberflex, Cyberflex Access, and e-gate are trademarks or registered trademarks of Schlumberger. Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation. Other company, product, and service names may be trademarks or service marks of others.
-
Page 3: Table Of Contents
Table of Contents Introduction .........1 Installation . -
Page 5: Introduction
The Reflex USB smart card reader uses the computer’s Universal Serial Bus (USB) port to transfer data at rates up to 115,200 bps. This high data transfer rate makes the Reflex USB smart card reader ideal for e-commerce and PKI applications that require smart cards to store certificates, generate digital signatures, and perform advanced encryption. - Page 6 Chapter 1 - Introduction Other System Requirements — Universal Serial Bus 1.1 or later Port • Cards Supported The Reflex USB smart card reader works with all leading ISO 7816-compatible microprocessor cards, including: Cryptographic cards • Java cards • Subscriber Identity Modules (SIMs) •...
-
Page 7: Installation
Overview of the installation sequence on each operating system. For • detailed instructions, see the sections that follow. Summary of each operating system’s Plug-and-Play or hot pluggable • capability. Summary of the expected behavior of the Reflex USB smart card reader’s • power light on each operating system. -
Page 8: Unsigned Driver Warning Messages
Smart Card Resource Manager detects Reflex USB smart card reader at boot-time (mid-session connect/disconnect detected only at reboot). Power light: Reflex USB power light is on continuously when the • reader is connected to the computer via a USB port (power light blinks continuously when a card is fully inserted into the Reflex USB smart card reader). -
Page 9: Installing On Windows 98 Or Windows Me
Smart Card Resource Manager detects it only during reboot or restart. Therefore, although you will see the Reflex USB smart card reader listed in the DeviceManager as an installed device after you complete step 2, the Reflex USB smart card reader is not usable until you reboot. -
Page 10: Updating On Windows 98 Or Windows Me
To make the Reflex USB reader functional, reconnect it and reboot. At this point you are ready to start using the Reflex USB smart card reader. You can test the reader setup using the Smart Card Reader Tools. From the →... - Page 11 In the device’s Properties, click the Driver tab, and then click the Update Driver button. The Update Device Manager wizard is launched and guides you through the process of locating the new Reflex USB driver. If you need more information about using the wizard, refer to the operating system’s Help. Step 3: Reboot the computer After the wizard has finished updating the Reflex USB driver, reboot.
-
Page 12: Installing Or Updating On Windows 2000 Or Windows Xp
Chapter 2 - Installation Installing or Updating on Windows 2000 or Windows XP To install or update the SchlumbergerSema Reflex USB smart card reader on a Windows 2000 or Windows XP computer, complete these tasks, which are described in more detail in the sections that follow. - Page 13 The Smart Card Resource Manager automatically detects the reader’s change in status whenever you disconnect or reconnect it. At this point you are ready to start using the Reflex USB smart card reader. You can test the reader setup using the Smart Card Reader Tools. From the →...
-
Page 15: Troubleshooting
Reflex USB smart card securely inserted in a USB port on the computer. See “Installation Notes” starting on page 3 for a summary of the expected behavior of the Reflex USB smart card reader power light on each operating system. - Page 16 USB smart card configure the reader properly in the future. Solution: Uninstall the reader and then reinstall it on Reflex USB smart card your system. For information about uninstalling hardware, see the documentation for your system. Reflex USB Reader Installation Guide...
- Page 17 Reflex USB smart card not function again in the current Windows session, even if you reconnect it. Reconnect the Reflex USB smart card reader and reboot the Solution: system. The Smart Card Resource Manager detects the Reflex USB smart card reader only at boot-time on Windows 98 and Windows Me computers.
- Page 18 Reflex USB smart card Windows session, close the message boxes and continue the session. The Reflex USB is not using the driver I installed The operating system chose the wrong reader driver On Windows 2000 and Windows XP systems, the operating...
- Page 19 Control Panel. Double-click System, click the Hardware tab, and then click the Device Manager… button. → To start the Device Manager on Windows XP, select Start Control Panel. Double-click System, click the Hardware tab, and then click the Device Manager… button. Reflex USB Reader Installation Guide...
- Page 20 In the Select a device driver screen, click Have Disk … In the Install from Disk screen, type in or browse to the \Program Files\Schlumberger\Smart Card Readers\reader_name directory, and click In the Select a Device Driver window, select the new device driver from the list, and click Next.
-
Page 21: Index
Index cards supported power light behavior product specifications driver checking version manually updating requirements operating system system installation 3–9 on Windows 2000/Windows XP on Windows 98/Windows Me summary smart cards supported introduction 1–2 specifications, product standards supported smart cards system requirements operating system requirements troubleshooting 11–16... - Page 22 Index: U update driver, manually on Windows 2000/Windows XP on Windows 98/Windows Me Windows 2000/Windows XP installation update Windows 98/Windows Me installation update Reflex USB Reader Installation Guide...
Need help?
Do you have a question about the Reflex USB and is the answer not in the manual?
Questions and answers