Content Index Disclaimer of Warranties 5.1.7 Off-Line Scan Uncorrectable Sector Count Disclaimer of Warranties 5.1.8 Seek Error Rate Before You Start 5.1.9 Temperature Important Notice 5.2 Update System Safety Precautions 5.3 System Info. Content Index 5.4 Set Target HDD Content Index Capacity Chapter ①...
Disclaimer of Warranties All HDD duplicators are made specifically for data backup with legal authorities from copyright owners. Any unauthorized action of copyright is strictly prohibited, and the original manufacturer disclaims all warranties or representations of illegal actions by users. The manufacturer also disclaims any liability for any of losses or damages due to not be able to perform its undertakings or provide any of the services attributable to any events or circumstances beyond our control.
Before you start Important Notice Read the complete operation instruction carefully contributes to better • operation. Make sure the source device is correct and workable. • To guarantee data consistency, strongly suggest the capacity of source • and targets should be the same. It is strongly suggest to use “Copy+Compare”...
Chapter ➀ - Product Introduction 1 Features High copy speed supports for duplication and comparison. • Support reading/writing speed measuring function. • Show the detailed information of HDD and its quality. • Auto power control system helps to protect the HDD from any damage •...
Chapter ➀ - Product Introduction 2 Product Overview 2.1 System Overview Red : Fail Green : Pass Yellow : Powering Target port Source port Backward Forward / OK Cancel / Back 2.2 LCD Configuration Target HDD Total size (Source) CARRY HDD MINI DUPLICATOR HI-SPEED Function Time (mm:ss)
Chapter ➀ - Product Introduction 3 Function Table Function Description To copy source HDD to multiple target HDDs. Refer to function [6.1 Copy Area] for 4 different 1. Copy copy modes selection. 2. Compare To compare data bit for bit between source and target HDDs. It makes copy first and then compare target HDD with source HDD to ensure data 3.Copy +Compare correctness.
Page 9
Chapter ➀ - Product Introduction 5.1.1 Model Number To show HDD's model number. 5.1.2 Version of Firmware To show HDD's firmware version. 5.1.3 Serial Number To show the serial number of HDD. 5.1.4 Device Power Cycle To show the count of HDD's turning on and off. 5.1.5 Power-on Hours 5.1 Show Disk Info.
Page 10
Chapter ➀ - Product Introduction 6.1.1 System and Files To copy source HDD's data area only. 6.1.2 ALL Partitions To copy source HDD's all partitions. 6.1 Copy Area 6.1.3 Whole HDD To copy the whole source HDD. 6.1.4 Percentage(%) To copy percentage range of source HDD. 6.2 Skip Error Set to ignore error of source HDD while copying.
Chapter ➁ - Function Introduction 1 Copy It copies data from the source HDD to the target HDD. Please ensure you have selected the copy mode require before executing the copying process. Refer to function [6.1 Copy Area] for details. Copy Process Total data capacity Copy...
Chapter ➁ - Function Introduction 4 Erase There are Quick Erase, Full Erase, DoD Erase, DoD EraseComp , and Secure Erase, totally 5 kinds of erasing modes. Select the appropriate erase method when you would like to dispose or reuse the HDDs. •Users can go to Function [6.4.2 Erase Master] to select if Note erasing the source HDD.
Chapter ➁ - Function Introduction Erasing Erasing 1 HDD [02] 465G DoD Erase 2:05 Erase[00] 4818M The system will show the result after finishing DoD Erase Pass: 5 Fail: 0 4.4 DoD Erase Comp As well as DoD erase, this function will also execute compare function to make sure the random bit was correctly written.
Chapter ➁ - Function Introduction 4.5 Secure Erase The international authorized high standard Secure Erase function. It overwrites every single track on the hard drive with "00". Even PA/DCO or other data area which are not able to load, can be erased all together. •Please do not disrupt during Secure Erase, otherwise it would cause Note irretrievable error on HDD, which turns the HDD unusable.
Chapter ➁ - Function Introduction 5.1.4 Device Power Cycle This function is to show the count of HDD's turning on and off. [Disc Info.] [Device Power C] 4.Device Power C 5.1.5 Power-on Hours This function is to show the total hours of HDD powering-on. [Disc Info.] [Power-on Hours] 5.Power-on Hours...
Chapter ➁ - Function Introduction 5.1.8 Seek Error Rate This function is to show the error rate of searching for data. It can represent the damage rate of data stored in the HDD. [Disc Info.] [Seek Error Rat] 8.Seek Error Rat 5.1.9 Temperature This function is to show the temperature of HDD.
Chapter ➁ - Function Introduction ⊳ Download the BIOS from the PC to your HDD. HDD Enclosure ⊳ Plug the HDD into Port 1of the duplicator, select Function 5.2.1 to update BIOS, and wait for about 1 minute to finish the update process.
Chapter ➁ - Function Introduction 5.5 Read Speed This function is to measure the reading speed of the HDD by reading the whole HDD. 2:30 465G 89.0M/S 12.8G 5.6 Write Speed This function is to measure the writing speed of the HDD by writing the whole HDD.
Chapter ➁ - Function Introduction Source HDD 320GB Tatget HDD 320GB Data : 20GB When choosing “System and Files Copy”, only 20G data will be Partition1 : 90GB copied, and it just takes 6.2% time compared to “Whole HDD Copy”. The target HDD will be exactly the same as source HDD after copy.
Chapter ➁ - Function Introduction 6.1.3 Whole HDD This mode will copy the entire HDD, regardless of content, format, partition or free space. This mode will take much more time to duplicate the source HDD completely. [Copy Area] Whole HDD Source HDD 320GB Tatget HDD 320GB Data : 20GB...
Chapter ➁ - Function Introduction Source HDD 500GB Tatget HDD 500GB Data:250GB Only percentage range from25% to 32% will be copied. Partition:250GB 500GB 6.2 Skip Error This function sets the volume of errors that is acceptable for you to skip during the copy process.
Chapter ➁ - Function Introduction [Unknown Format] Copy Unknown 6.4.1.2 Skip Unknown The setting skips the unknown format area during copy process. [Unknown Format] Skip Unknown 6.4.2 Erase Master This function is to set if erasing the source or not when executing erasing function.
Chapter ➁ - Function Introduction 6.4.3.2 Big Random Data A set of different random character to be written into a set of area. This erase pattern method is safer for preventing from data recovered. 26A5C8781 BF51337E81 AA9641D3B 5CDA756B1 3BAFF21FF4 1FBAC4C99 [Erase Pattern] 7EDAF1237 Big Random Data...
Chapter ➁ - Function Introduction ❶ Copy and Setting: Yes, copy. Copy data from source to target including HPA area of source. It will not only set the target HDD the same HPA setting as the source HDD, but also copy the data in the HPA area. ❷...
Chapter ➁ - Function Introduction 6.4.7 Transfer Rate You can select the best transfer rate from UDMA 2 to UDMA7 for your HDD duplication process. If you are not confident on the HDD quality or you find a high failure rate on copy or compare. It is recommended to slow down the UDMA mode.
Chapter ➂ - Specification Product Name Carry Mini Super High Speed HDD Dupe Product Number PRO250 Targets 1:1 (2-port) Support HDD Interface Directly 1.8”/2.5”/3.5” SATA HDD and SSD Control Button 4 push buttons( ▲ , ▼ , OK, ESC ) All major brand of 2.5"/3.5"...