Advertisement
1200 North Main St.
Fostoria, OH 44830
Phone: 800-495-4525
Fax:
419-435-0842
www.tpicorp.com
SELF-CONTAINED POWER MISTER
PM-18FO
IMPORTANT SAFETY
INFORMATION INSIDE
• Serious injury or death possible.
• Read, understand, and follow all
safety information and
instructions in this manual before
using or servicing this product.
• Retain these instructions for
future reference.
Issue Date: 3-11-05 Rev. Date: 9-12-07 Rev. Level: 13
MODELS: PM-18FO, PM-18S, PM-18C
PM-18S
Specifications
PM-18C Assembly
Set-up / Operation
Replacement parts
Maintenance
Warranty
ECN: n/a
OIPM P/N: 3420433
If you have questions about the
product you have purchased or would
like to leave us feedback please
contact us via our website
www.fostoriaindustries.com
or by calling 1-800-495-4525.
PM-18C
CONTENTS
Pages 2,3
Pages 3,4
Pages 5,6
Page 7
Page 8
Page 8
Page 1 of 8
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for TPI PM-18FO
Summary of Contents for TPI PM-18FO
- Page 1 Fostoria, OH 44830 contact us via our website Phone: 800-495-4525 www.fostoriaindustries.com or by calling 1-800-495-4525. Fax: 419-435-0842 www.tpicorp.com SELF-CONTAINED POWER MISTER MODELS: PM-18FO, PM-18S, PM-18C PM-18FO PM-18S PM-18C IMPORTANT SAFETY CONTENTS INFORMATION INSIDE • Serious injury or death possible. Specifications...
- Page 2 The cool air you will now enjoy when using this misting equipment is created through the process of evaporation. Heat is required to change water from a liquid to a gas or “water vapor”. TPI Corporation’s self-contained power misting equipment creates a “fog” by pumping water at a very low flow rate through small nozzles. When combined with the air added by a fan, this fog is rapidly evaporated.
- Page 3 SPECIFICATIONS (continued) MODEL: PM-18S • One 18-inch fan head with white powder-coated guard mounted on a yoke attached to the pump enclosure. • An integral ground fault circuit interrupter (GFCI) is attached to the power cord. • Equipped with a power cutoff tip switch. •...
- Page 4 PM-18C CART ASSEMBLY (continued) Pump enclosure Intake line yoke Filter Retaining strap Cooler Spout extension Retaining ring TOOLS REQUIRED: Screwdriver, adjustable wrench, hammer, and pliers. 1. Place base (item 5) on flat work surface with legs downward as shown above. Install wheels onto axle; making sure the hub extension is facing inward toward the base.
- Page 5 SET-UP / OPERATION 1. Always operate the Power Mister on a level surface. In the event the unit is tipped over or tilted more than 35 degrees, a built-in tip-over switch will shut off power to the pump and fan. Power will be restored when unit is placed in the upright ELECTRICAL SHOCK position.
- Page 6 5. Follow Set-up / Operation instructions on page 5. Intake line * Model PM-18FO comes without a cooler. Since the Filter pump enclosure is specifically made to fit a 10-gallon Igloo cooler, it must be used only with a similar Igloo cooler, supplied by the user.
- Page 7 ASSEMBLED VIEW AND REPLACEMENT PARTS LIST FOR PM-18FO & PM-18S 10, 12 ITEM # QTY. DESCRIPTION 6399099 FRONT GUARD (PAINTED) 63991002 REAR GUARD (PAINTED) 58381001 SUPPORT TUBE ASSEMBLY 58364003 MOTOR TOTALLY ENCLOSED 44115001 CORDSET 58299008 FAN BLADE ASSEMBLY 44114001 SWITCH (TOGGLE-WATER PROOF)
- Page 8 TPI Corporation, however, reserves the right to refuse any return, at our discretion, if TPI Corporation is not responsible for error. All special, custom made or equipment with special finishes, and modified versions of cataloged numbers are not NOZZLES returnable.
Need help?
Do you have a question about the PM-18FO and is the answer not in the manual?
Questions and answers