Table of Contents
Advertisement
Quick Links
This is a Class A device and is intended for use in a
light industrial environment. It is not intended nor
approved for use in an industrial or residential
environment.
Part# 07M2168A-UM
Rev. C
Revised 4/20/10
An ISO-9001Certified
Company
USER
MANUAL
CopperLink™ Ethernet
Extenders
Models 2168A and 2158A
SALES OFFICE
(301) 975-1000
TECHNICAL SUPPORT
(301) 975-1007
Advertisement
Table of Contents
Related Manuals for Patton electronics CopperLink Ethernet Extenders 2158A
Summary of Contents for Patton electronics CopperLink Ethernet Extenders 2158A
- Page 1 This is a Class A device and is intended for use in a light industrial environment. It is not intended nor approved for use in an industrial or residential environment. Part# 07M2168A-UM Rev. C Revised 4/20/10 An ISO-9001Certified Company USER MANUAL CopperLink™...
-
Page 2: Table Of Contents
CONTENTS Warranty Information ... 4 Compliance... 4 EMC Compliance:... 4 Safety Compliance: ... 4 PSTN Compliance: ... 4 Radio and TV Interference (FCC Part 15) ... 5 CE Declaration of Conformity ... 5 Authorized European Representative... 5 Service... 5 Safety When Working With Electricity ... 6 General Information... - Page 3 Model 2168A and 2158A Series Factory Replacement Parts and Accessories... 22 CopperLink Series Interface Pin Assignment ... 24 C.1 10/100Base-T Interface ... 24 RJ-45 ... 24 C.2 CopperLink Interface ... 24 RJ-45 ... 24 Terminal Block... 24 Distance Chart, Based on 24 AWG (0.5 MM) ... 25...
-
Page 4: Warranty Information
1.0 WARRANTY INFORMATION Patton Electronics warrants all CopperLink Ethernet Extender compo- nents to be free from defects, and will—at our option—repair or replace the product should it fail within one year from the first date of the ship- ment. This warranty is limited to defects in workmanship or materials, and does not cover customer damage, abuse or unauthorized modification. -
Page 5: Radio And Tv Interference (Fcc Part 15)
1.2 RADIO AND TV INTERFERENCE (FCC PART 15) This equipment generates and uses radio frequency energy, and if not installed and used properly—that is, in strict accordance with the manu- facturer's instructions—may cause interference to radio and television reception. This equipment has been tested and found to comply with the limits for a Class A computing device in accordance with the specifica- tions in Subpart B of Part 15 of FCC rules, which are designed to provide reasonable protection from such interference in a commercial installa-... -
Page 6: Safety When Working With Electricity
Note Packages received without an RMA number will not be accepted. 1.6 SAFETY WHEN WORKING WITH ELECTRICITY • This device contains no user serviceable parts. The • The external power adapter shall be a listed Limited WARNING • Do not work on the system or connect or disconnect In accordance with the requirements of council direc- tive 2002/96/EC on Waste of Electrical and Electronic Equipment (WEEE), ensure that at end-of-life you sepa-... -
Page 7: General Information
2.0 GENERAL INFORMATION Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and is warranted for one year for parts and labor. If any questions or problems arise during installation or use of this product, contact Patton Electronics Technical Support at +1 (301) 975-1007. -
Page 8: Description
2.2 DESCRIPTION The Patton Electronics CopperLink/L and CopperLink/R Ethernet Extenders provide high-speed LAN connections between peered Ether- net LANs, remote PCs, or any other network enabled 10/100Base-T device. Operating in pairs, a CopperLink/L (local) located at one end of the LAN extension and a CopperLink/R (remote) at the other end, these units can automatically forward LAN broadcasts, multicasts, and frames across a 2- wire voice-grade twisted-pair link. -
Page 9: Installation
Because the CopperLink Ethernet Extender requires no configuration, it can be installed quickly. Note If asymmetric transmission or line rates other than 12.5 Mbps are required , refer to section 4.0, “Configuration” on page 16. 3.1 UNIT INSTALLATION Do the following: 1. -
Page 10: Grounding The Copperlink Ethernet Extender
3.2 GROUNDING THE COPPERLINK ETHERNET EXTENDER Before installing the CopperLink Ethernet Extender, it is important to establish a good grounding connection first. 1. Assemble a ground wire using #10 AWG wire with green-and-yel- low-colored insulation and two ring terminals. Make the wire long enough to reach one of the following earth ground sources: —... - Page 11 The RJ-45 connector on the CopperLink Ethernet Extender's twisted pair interface is polarity insensitive and is wired for a two-wire inter- face. The signal/pin relationship is shown in Figure 3. Figure 3. CopperLink Ethernet Extender (RJ-45) twisted pair line interface. The terminal block connector on the CopperLink Ethernet Extender's twisted pair interface is polarity insensitive and is wired for a two-wire interface.
-
Page 12: Using A Ferrite Clamp To Connect The Line Interface
Using a Ferrite Clamp to Connect the Line Interface • The ferrite clamp that is shipped with the unit must be used as detailed in the following instructions in order to meet EMC requirements. WARNING Connecting the ferrite clamp to the RJ-45 port. To connect the ferrite clamp to the RJ-45 port: 1. -
Page 13: Connecting The Ferrite Clamp To The Terminal Block
Connecting the ferrite clamp to the terminal block. To connect the ferrite clamp to the terminal block: 1. Place the cable inside the ferrite clamp, leaving about 1-2 inches of cable between the unit and clamp. 2. Wrap the cable tightly around the clamp two times and secure the wire firmly in the clamp channel. -
Page 14: Connecting The 10/100Base-T Ethernet Interface
3.4 CONNECTING THE 10/100BASE-T ETHERNET INTERFACE The RJ-45 port labeled Ethernet is the Auto-MDIX10/100Base-T inter- face. This port is designed to connect directly to a 10/100Base-T net- work. Figure 7 shows the signal/pin relationships on this interface. You may connect this port to a hub or PC using a straight through or cross- over cable that is up to 328 ft long. -
Page 15: Connecting Power
3.5 CONNECTING POWER • Do not connect power to the DC Mains at this time. • There are no user-serviceable parts in the power supply sec tion of the CopperLink Ethernet Extender. Contact Patton Elec- WARNING tronics Technical support at (301)975-1007, via our web site at http://www.patton.com, or by e-mail at support@pat- ton.com, for more information. -
Page 16: Configuration
4.0 CONFIGURATION The CopperLink Models 2168A and 2168A/TB45 have an eight-position DIP switch for configuring the unit for a wide variety of applications. This section describes switch locations and explains the different configura- tions. The Model 2158A does not include dip switches. 4.1 CONFIGURING THE HARDWARE DIP SWITCHES Using a small flat-tip screwdriver, remove the protective cover located on the underside of the CopperLink Ethernet Extender (see Figure 8). -
Page 17: Configuring Dip Switch Sw
4.2 CONFIGURING DIP SWITCH SW DIP switch SW is where you configure the CopperLink line rate, and if the rate is symmetric or asymmetric. Switches SW-2 and SW-4: Data Rate Use switches SW-2 and SW-4 to configure the CopperLink line rates. Table 1: Symmetric CopperLink Line Rates Selection Chart SW-2 SW-3... -
Page 18: Operation
Once the CopperLink Ethernet Extenders are properly installed, they should operate transparently. No user settings required. This section describes reading the LED status monitors. 5.1 POWER UP Before applying power to the CopperLink Ethernet Extender, please review section 3.5, “Connecting Power” on page 15 to verify that the unit is connected to the appropriate power source. - Page 19 Table 4: Front panel LED description for the 2168A On (green) when power is applied to the unit. Off Power when no power is applied to the unit. On (green) when the end-to-end CopperLink link CopperLink - between the units is established. Off when the link Link has not been established or when the link fails Flashes yellow at different rates to indicate the...
-
Page 20: Specifications
A.1 LAN CONNECTION • Unshielded RJ-45, 10/100Base-T, IEEE 802.3 Ethernet • CopperLink Connection: — 2168A/TB45: RJ-45 and Terminal Block — 2168A/2158A: RJ-45 only A.2 TRANSMISSION LINE Two-wire unconditioned twisted pair. A.3 COPPERLINK LINE RATE 16.67 Mbps (Model 2168A and Model 2168A/TB45) and 12.55 Mbps (Model 2158A) symmetric upstream/downstream. -
Page 21: Power Supply
A.7 POWER SUPPLY Input power: 5 VDC, 1A Power consumption: 560 mA at 5 VDC (typical) External AC and DC options: • AC: 120 VAC, 220 VAC, and UI (120–240 VAC) • DC: 12 VDC, 24 VDC and 48 VDC Internal 36-72VDC (nominal 48V) Terminal Block Plug (1x3, 3.81mm, with screws) Pin Header Socket Connector A.8 TEMPERATURE RANGE... -
Page 22: Model 2168A And 2158A Series Factory Replacement Parts And Accessories
MODEL 2168A AND 2158A SERIES FACTORY REPLACEMENT PARTS AND ACCESSORIES Patton Model # Base Models 2158A/E-2PK 2158A/EUI-2PK 2158A/L/E 2158A/L/EUI 2158A/R/E 2158A/R/EUI 2168A/E-2PK 2168A/EUI-2PK 2168A/L/E 2168A/L/EUI 2168A/L/TB45/E 2168A/L/TB45/EUI 2168A/R/E 2168A/R/EUI 2168A/R/TB45/E 2168A/R/TB45/EUI 2168A/TB45/E-2PK 2168A/TB45/EUI-2PK 0 7 M 2 1 6 8 A -U M APPENDIX B Description CopperLink 12.5 Mbps Ethernet Extender Kit... -
Page 23: Power Supplies
Patton Model # Power Supplies 08055DCUI 08055-120-5-1 12V-PSM 24V-PSM 48V-PSM Power Cords (Only required with optional UI power supply (08055DCUI) 0805US 0805EUR 0805UK 0805AUS 0805DEN 0805FR 0805IN 0805IS 0805JAP 0805SW Description 100-240VAC (+5V reg. DC/2A) Universal Input Adapter. 120 VAC (+5V reg. DC/1A) Input Adapter 12 VDC Input Adapter 24 VDC Input Adapter 48 VDC Input Adapter... -
Page 24: Copperlink Series Interface Pin Assignment
APPENDIX C COPPERLINK SERIES INTERFACE PIN ASSIGNMENT C.1 10/100BASE-T INTERFACE RJ-45 • Pin 1: TX+/RX+ • Pin 2: TX-/RX- • Pin 3: RX+/TX+ • Pin 6: RX-/TX- • Pins 4, 5, 7, 8: no connection C.2 COPPERLINK INTERFACE RJ-45 • Pin 4: RING •... -
Page 25: Distance Chart, Based On 24 Awg (0.5 Mm)
DISTANCE CHART, BASED ON 24 AWG (0.5 MM) Symm Line Rate 6.25 Mbps 9.38 Mbps 12.5 Mbps 16.67 Mbps *. This is the only option available for Model 2158A. Asymm Line Rate (DS/US) 4.17 Mbps/1.56 Mbps (Mode 0) 9.38 Mbps/1.56 Mbps 16.67 Mbps/2.34 Mbps DS = downstream from L unit to R unit Note... - Page 26 _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________...
- Page 27 _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________...
- Page 28 _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ Copyright © 2010. Patton Electronics Company All Rights Reserved.