Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Stealth Digi-Arc 160LT
Summary of Contents for Stealth Digi-Arc 160LT
- Page 1 DIGI-ARC 160LT Part No. 9021H OPERATOR’S MANUAL...
- Page 2 STEALTH DIGI-ARC 160LT...
-
Page 3: Table Of Contents
STEALTH DIGI-ARC 160LT CONTENTS SAFETY SUMMARY MAIN ELECTRICAL DIAGRAM TECHNICAL INFORMATION OPERATION CONTROL AND CONNECTORS INSTALLATION & ADJUSTMENT 6.1 INSTALLATION 6.2 OPERATION 6.3 WELDING TABLE OPERATION NOTICES 7.1 INSTALLATION 7.2 SAFETY MAINTENANCE TROUBLESHOOTING & SERVICE... -
Page 4: Safety
1. SAFETY STEALTH DIGI-ARC 160LT 1. SAFETY 1. SAFETY 1. SAFETY 1. SAFETY Welding may damage your body or others, so please take protection measure in 1. SAFETY 1. SAFETY Welding may damage your body or others, so please take protection measure in operation. -
Page 5: Summary
The machine can be easily ignited with little splash and good weld bead. operation. The frame is Stability of the machine, which can keep working under high The DIGI-ARC 160LT has a high duty cycle – even at 40ºC – for continuous temperature and corrosion environment. -
Page 6: Technical Information
STEALTH DIGI-ARC 160LT 4. TECHNICAL INFORMATION DIGI-ARC 160LT Power Supply Voltage (V) 1~230±10% Frequency (Hz) 50/60 Rated Input Power (Kw) 5.0 MMA / 3.5 TIG Rate Input Current (A) 37 MMA / 27 TIG 40% 160A Duty cycle (40ºC / 10 min) -
Page 7: Operation Control And Connectors
(7) Power switch: control power through and break. (8) Fan: Help plant cooling. STEALTH DIGI-ARC 160LT (9) Power Access client: access to cable. 5. OPERATION CONTROL AND CONNECTORS (10) Conversion switch: choose LIFT TIG; choose MMA. Positive output: connect welding to the clamp. -
Page 8: Installation & Adjustment
STEALTH DIGI-ARC 160LT 6. INSTALLATION & ADJUSTMENT Note: Please follow steps in strict accordance with installation instructions! Electrical connection must be disconnected after power is switched off! Equipment protection level is IP23. Do not use in the rain! Installation 6.1.1 Each machine is fitted with a power cable based on the input voltage connected to the appropriate selection. -
Page 9: Welding Table
STEALTH DIGI-ARC 160LT Welding Table Note: The following table applies to low-carbon steel. For other materials, please refer to related information. Electrode diameter Recommended welding Recommended welding (mm) current (A) voltage (V) 20~60 20.8~22.4 44~84 21.76~23.36 60~100 22.4~24 80~120 23.2~24.8 108~148 23.32~24.92... -
Page 10: Maintenance
STEALTH DIGI-ARC 160LT 7.2.3 Prevent over-voltage The welding voltage within the circuit will automatically compensate to ensure the welding current is in the permitted range. If the voltage exceeds the allowable value it can damage the machine. The welder should be fully aware of this and take appropriate preventive measures. -
Page 11: Troubleshooting & Service
STEALTH DIGI-ARC 160LT TROUBLESHOOTING & SERVICE Common faults and solutions: Symptom Solution Power indicator does not light, fan does not – Make sure the power switch is turned on. turn, no welding output – Confirm that the power input cable is connected to electricity. - Page 12 STEALTH DIGI-ARC 160LT...