Automatic Cooking; Temperature And Power Settings - Electrolux Thermetic GU series Operating Instruction

Tilting boiling pans, round, electric
Table of Contents

Advertisement

4.3

Automatic cooking

TT Button, activation of settings
LT
Lamp, cooking temperature
DT Button, cooking time
LD Lamp, cooking time expires
ZT Button, starting time
LZ Lamp, starting time
LR Lamp, soft settings
Q
Button, acoustic signal
R
Button, soft
LS Lamp, temperature
pre-setting
AT Display, cooking tempera-
ture
T
Temperature selection knob
AD Display, remaining cooking
time
D
Cooking time knob
AZ Display, time
Z
Starting time knob
LU
LC
C
U
S
Control switch
Fig. 3
Right console
Switching on
Switch on the control switch (S) turn from position 0 to I. This
switches on the temperature pre-setting function. The lamp
(LS) lights up.
0 = Off
I = on
Set the desired cooking temperature (flashing nominal
value) with the temperature selection knob (T) on the display
(AT).
Turn right = increase
Turn left = reduction
Smallest change = 1°C
Programming the cooking time and the starting time (or
only one function).
Pressing the button (DT) switches on the programme for the
cooking time (flashing nominal value). The desired cooking
time is set with the cooking time knob (D) on the display (AD).
Turn right = increase
Turn left = reduction
Smallest change = 1 minute
The lamp (LD) only lights up when the desired temperature
has been reached and the cooking time expires.
Pressing the button (ZT) switches on the programme for the
starting point (flashing nominal value). Set the desired starting
time with the starting time knob (Z) on the display (AZ)
Turn right = increase
Turn left = reduction
Smallest change = 1 minute
The acoustic signal will sound three times and the lamp (LZ)
will light up when the starting time has been reached.
The following pre-programmed nominal functions
Cooking temperature
Cooking time
Starting time
are all activated by pressing the button (TT).
The following displays
Cooking temperature (AT)
Remaining cooking time (AD)
62.9692.01
OPERATING INSTRUCTIONS
Clock time (AZ)
indicate the current value.
The lamp (LT) will continue to flash until the nominal cooking
temperature is reached. It then stays on permanently.
4.4
Temperature setting
If the nominal temperature set on the display (AT) is below the
boiling point of water (26 - 212°F (97 - 100°C)), this tempera-
ture will be attained during heating up and then maintained at
this value by the electronic controls and the careful supply of
energy. The nominal temperature is not exceeded in this proc-
ess.
When certain foods with poor conductivity are heated, such as
sugar solutions, nominal temperature settings between 212
and 230°F (100 - 110°C) are required in order to achieve boil-
ing. The correct setting is largely a matter of experience.
Power setting
Fixed power settings can also be programmed in using the
electronic controller. In this case, the pre-set energy is sup-
plied to the food after boiling point has been reached. Setting
the controller to fixed power settings is done in order to enter
the degree of boiling in the food individually, i.e. dependent on
the type of food, the amount of food, the position of the lid, etc.
The following fixed power settings can be entered on the dis-
play (AT):
HOLD setting
The HOLD section is located above the power adjustment L1 -
L9. The knob (T) is used to set a HOLD temperature between
122°F and 210°F (50 and 99°C).
HOLD temperature set: A three digit display (AT) indicates:
H for Hold,
22 - 85 the temperature between 122 and 185°F
03 -10 the temperature between 203 and 210°F (
Owing to the internal conversion in °C not every value is possi-
ble. The following settings are allowed:
Display
H22
H31
H40
H49
H58
H67
H76
H85
H94
H03
H10
The programmed cooking process then operates as follows:
the food is first heated to simmering temperature (approx.
212°F). When simmering temperature is reached, the energy
supply is switched off. The food cools down and is then kept at
the HOLD temperature that has previously been set.

Temperature and power settings

Setting (AT)
Power %
L1
6
L2
12
L3
25
L4
37
L5
50
L6
62
L7
75
L8
87
L9
100
Hold-Temperature
°F
122
131
140
149
158
167
176
185
194
203
210
Page 7

Advertisement

Table of Contents
loading

This manual is also suitable for:

Thermetic ku series

Table of Contents