Advertisement
Remove the flight vehicle battery safely at
the conclusion of flight. this should be
made into a post flight habit to avoid
unforeseeable problems.
ifoIrCri -ffiqitTr'kfIRT,
iii4Matff7tPilattiAME180
Warning: If left connected in the
flight
vehiclefor long duration, the battery may
be damageddue to over-discharge, or even
become fire hazards.
EgIVIRT, 14415z 1 7M3AWM914.
nitmtemtonalito
1200MAH 7.4V 30C Li-Po battery
30CtE( 170,e,
1200MAH 7.4V 'a ,
G
Lowest
OP-
NW
Ad
a
g o Mr
AO
11
mi
The throttle stick to the bottom
(Figure 1), turn the remote
control power(Figure 2).
ITTFaItiii(AnEal(?))0
Turn the remote ON. Connect the copter
battery and PCB cable, and place it on
Level ground. The copter LEDs become
static and then start blinking. Push the
Throttle Stick STRAIGHT UP to the highest
point and then PULL it back down slowly.
The binding process is complete. And the
copter will respond to controls from the
Remote. IMPORTANT: Do not move the
copter while the binding process is on, as
the Gyro is being set to neutral.
)14Eg3tiMPfi
tfLPHIAMILHITN4
6M#11,4, 1 illni31ff
$11.411 -
VzNW31S. , NOtEriff#Itgilgig,
i&SK
90-4- 4 ihnwtpstmo
44,
1200MAH 7.4V 30C Li-Po battery
30CEtDte
1200MAH 7.4VEga
BINDING OF RADIO TRANSMITTER AND RECEIVER
iiK734g-iikalYglg
•
•
ON/OFF
5: F/
Turn off the transmitter. If transmitter is not
to be used for a long duration, please
removethe battery for storage.
17f] Vi,i FM, -
KniETTICEIMIVICITIalt
itfIY.W4r 4 ".1M.
Warning: If the AA batteries are left in the
transmitter, potential leakage could occur
which may damage the transmitter, and
create fire hazards.
EglAfIRT, ;144REE' itairtn#9 941;f6125,
gitALE:k3V71n)a -Rit
N
E
Outstanding Orientation Mode, can start and
fly in any orientation. If it flies far away, no
need to worry about losing the orientation.
5M.ligh4M- F -Cr5-ttAii165PINJAAO-U5-Plit
laMii:,PAMPErt,
1*§Klin
'Mr
it '7.
r,
• (C
•
NOTICE:
1.Orientation Mode: Connect the charged battery to the
drone. Place the drone on a FLAT surface. Switch "ON"
the Transmitter, The light in the drone blinks rapidly;
indicating the binding process is on. When the LED
remains constant, the binding process is complete.
2.After Tarantula flight,LED light of the body is the
indicator which the compass mode automatically
adjustment.Please don't control the joystick, you can
operate other actions after it left the ground which to
avoid the compass mode unnormal operated.
a 74:
AMV-4A4fle li*SlAg*ttil.A.tgACR
egTw3- 1 400.*x6C,',V, W)WiltIqDtgt1lAt
LEDng7,-AITIJ-ag-
U5-11E1J,
(2)Vg0,11+/A- LEDgItgiMt+MAIIIIMMt`z.T,
HYPER IOC FUNCTION
thACI - V74.4A,
7
Advertisement
