Summary of Contents for new brunswick innova 2000
- Page 1 Innova® 2000/2050 Shaker New Brunswick™ Innova 2000/2050 Shaker ® Operating manual...
- Page 2 ® Eppendorf and the Eppendorf logo are registered trademarks of Eppendorf AG, Germany. New Brunswick™ and the New Brunswick™ logo are trademarks of Eppendorf AG, Germany. Innova ® is a registered trademark of Eppendorf, Inc., USA.
-
Page 3: Table Of Contents
Table of contents ® New Brunswick Innova 2000/2050 Shaker English (EN) Table of contents Operating instructions ............. . 5 Using this manual . - Page 4 Innova 2000........
-
Page 5: Operating Instructions
Operating instructions ® New Brunswick Innova 2000/2050 Shaker English (EN) Operating instructions Using this manual Carefully read this operating manual before using the device for the first time. Also observe the operating manual enclosed with the accessories. The operating manual should be considered as part of the product and stored in a location that is easily accessible. -
Page 6: Symbols Used
Operating instructions ® New Brunswick Innova 2000/2050 Shaker English (EN) Symbols used Example Meaning You are requested to perform an action. Perform these actions in the sequence described. • List. References useful information. -
Page 7: Safety
Warnings for intended use WARNING! Heavy! Do not attempt to lift the Innova 2000/2050 Shaker by yourself. Ask for assistance or use suitable equipment when raising or handling the device. WARNING! Risk of explosion and injury or death! ... - Page 8 Safety ® New Brunswick Innova 2000/2050 Shaker English (EN)
-
Page 9: Product Description
Product description Main Illustration Abb. 3-1: Innova 2000/2050 front view Fig. 3-1: Innova 2000/2050 front view 1 Platform 3 Control panel 2 Temperature/monitor RTD probe and bracket Optional Unless otherwise indicated, all drawings represent both Innova 2000 and Innova 2050 models. -
Page 10: Features
4 Voltage selector Features The Innova 2000/2050 is a portable benchtop shaker utilizing a triple eccentric counterbalanced drive to provide horizontal plane rotary motion in a 19 mm (3/4 in) circular orbit. A Proportional/Integral (PI) microprocessor controller with instantaneous digital feedback controls the speed over a range of 25 – 500 RPM. -
Page 11: Alarms
2000/2050 Shaker English (EN) 3.2.2 Alarms The Innova 2000/2050 is equipped with audible and visible alarms that alert the user to the following conditions: • The end of a timed run • Deviation of shaking speed outside the tolerance limits 3.2.3... -
Page 12: Led Display
Product description ® New Brunswick Innova 2000/2050 Shaker English (EN) Abb. 3-3: Control panel MAINT TIME ° C MUTE START SELECT STOP Fig. 3-3: Control panel 1 Status indicators 3 Function indicators 2 LED display 4 Keypad 3.4.1 LED display The Innova control panel has a 3-digit LED display. -
Page 13: Keypad
(see Platforms on p. 31). The Innova 2000 can be used with a wide range of New Brunswick 28 cm x 33 cm (11 in × 13 in) platforms, which will accept a variety of clamps for flasks, test tubes, etc (see Tab. on p. 31). -
Page 14: Heavy Duty Construction
3.6.2 Motor The Innova 2000/2050 Shaker uses a brushless ball bearing DC motor. This low profile motor provides high torque along with quiet, efficient operation and low maintenance. The motor has a rating of 1/20 horsepower. 3.6.3... -
Page 15: Electronic Boards
The output can also be connected to a data logging computer with an analog data acquisition card. 3.8.2 Capacity upgrade option It is possible to significantly increase the capacity of an Innova 2000 shaker with an available capacity upgrade package (M1190-9910). This option will simply and easily convert an Innova 2000 to an Innova 2050. - Page 16 Product description ® New Brunswick Innova 2000/2050 Shaker English (EN)
-
Page 17: Installation
Installation ® New Brunswick Innova 2000/2050 Shaker English (EN) Installation Unpacking When you unpack the unit, inspect it carefully for any apparent damage that may have occurred during transit. Report any damage to the carrier and to Eppendorf Service Department. - Page 18 Installation ® New Brunswick Innova 2000/2050 Shaker English (EN) Abb. 4-1: Innova 2000 operating space 35 cm (17 in) 35 cm (17 in) Fig. 4-1: Innova 2000 operating space Abb. 4-2: Innova 2050 operating space 50 cm (20 in) 50 cm (20 in) Fig.
-
Page 19: Electrical Connections
Installation ® New Brunswick Innova 2000/2050 Shaker English (EN) Electrical connections WARNING! Risk of electric shock and/or damage to device! Use a grounded power supply. CAUTION! A detachable main power cord has been provided with your unit. Only use the cord provided with the unit. - Page 20 Installation ® New Brunswick Innova 2000/2050 Shaker English (EN) If you have purchased flask clamps for use with a universal platform, they will require installation. . All clamps are shipped complete with hardware. 1. Clamps are installed by securing the base of the clamp to the platform with the correct type and number of screws (see Clamp hardware on p.
-
Page 21: Operation
Operation ® New Brunswick Innova 2000/2050 Shaker English (EN) Operation Getting started To start the instrument, turn the ON/OFF switch on the back of shaker to the ON position. If the shaker is running, the LED display will track the speed as it accelerates to the last entered setpoint. -
Page 22: Canceling The Timer
Operation ® New Brunswick Innova 2000/2050 Shaker English (EN) • The display will read OFF • The time indicator will flash • The audible alarm will sound The setpoint may be changed during a run without stopping the shaker by following steps 1 and 2 above. -
Page 23: Total Running Time
Operation ® New Brunswick Innova 2000/2050 Shaker English (EN) The shaker may be stopped or started by pressing the START/STOP key. When starting, the unit will automatically return to the last function and speed setting. The audible alarm will sound until the speed is within 5 rpm of the setpoint. - Page 24 Operation ® New Brunswick Innova 2000/2050 Shaker English (EN) • For speed, each channel should have signal Abb. 5-1: Recorder connector as seen from the rear of the unit conditioning that accepts 0 – 5 V input. • For temperature, each chanel should have a signal conditioning that accepts 0 –...
-
Page 25: Maintenance
Routine maintenance No routine maintenance is required for the Innova 2000/2050 Shaker. The MAINT indicator light illuminates at the end of 10000 hours of use. At that time, contact your local Eppendorf Service Engineer, or call the Eppendorf Service Department. This periodic maintenance will keep your unit in premium condition. - Page 26 Maintenance ® New Brunswick Innova 2000/2050 Shaker English (EN) 1. Disconnect the unit from the power source. 2. Using a small screwdriver, remove the cover/fuse block located on the rear of the unit. 3. Remove the old fuse. 4. Insert a new one of the same type.
-
Page 27: Technical Data
Technical data ® New Brunswick Innova 2000/2050 Shaker English (EN) Technical data Specifications 7.1.1 Innova 2000 Tab. 7-1: Shaking Speed 25 – 500 rpm Control accuracy ±1 rpm Indication 3-Digit LED, in 1 rpm increments Stroke/Orbit 1.9 cm (¾ in) - Page 28 To attain speed accuracy at 401 – 500, the line voltage cannot be lower than 5 % of the rated voltage. The Innova 2000 can be upgraded to a larger capacity platform with a kit that converts this shaker to an Innova 2050. This kit can be installed in the field.
-
Page 29: Innova 2050
Technical data ® New Brunswick Innova 2000/2050 Shaker English (EN) 7.1.2 Innova 2050 Tab. 7-2: Shaking Speed 25 – 500 rpm Control accuracy ±1 rpm Indication 3-Digit LED, in 1 rpm increments Stroke/Orbit 1.9 cm (¾ in) Setpoint and Digital adjustment with PI microprocessor control and instantaneous visual control feedback. - Page 30 Technical data ® New Brunswick Innova 2000/2050 Shaker English (EN) At 25 – 400 rpm, the unit will perform to specifications with up to ±10 % line voltage fluctuation. To attain speed accuracy at 401 – 500 rpm, the line voltage cannot be lower than...
-
Page 31: Ordering Information
Ordering information ® New Brunswick Innova 2000/2050 Shaker English (EN) Ordering information Platforms Tab. 8-1: Innova 2000 platforms Part number Number of clamps Description 28 x 33 cm (11 x 13 in ) Platform AG2-UT Utility Carrier AG2-00 Utilility Tray... -
Page 32: Accessory Flask Clamps
Ordering information ® New Brunswick Innova 2000/2050 Shaker English (EN) Accessory flask clamps All clamps listed are made of stainless steel. Catalog number Clamp type ACE-105 10 mL Erlenmeyer ACE-255 25 mL Erlenmeyer ACE-505 50 mL Erlenmeyer ACE-125S 125 mL Erlenmeyer... -
Page 33: Service Parts
Power Cord 120 V 10 A P0720-2021 Power Cord 220 V P0180-0020 Bearing, Shielded, lower 6 M1190-6340 Bearing Assembly R-243 Drive Belt M1190-6330 Bearing Housing Assembly H-1386 Knob M1194-8000 Stainless Steel RTD (optional) Innova 2000 only M1190-9501 Foam Pad Innova 2050 only M1190-9502 Foam Pad... -
Page 34: Clamp Hardware
Ordering information ® New Brunswick Innova 2000/2050 Shaker English (EN) Clamp hardware Eppendorf flask clamps are used on a variety of shaker platforms. Flat Phillips and flat head screws of different lengths and thread pitch are used to secure the clamp. The following tables identify the proper screw for your shaker application by reference to the head style. -
Page 35: Transport, Storage And Disposal
Transport, storage and disposal ® New Brunswick Innova 2000/2050 Shaker English (EN) Transport, storage and disposal Disposal In case the product is to be disposed of, the relevant legal regulations are to be observed. Information on the disposal of electrical and electronic devices in the European Community: Within the European Community, the disposal of electrical devices is regulated by national regulations based on EU Directive 2012/19/EU pertaining to waste electrical and electronic equipment (WEEE). -
Page 36: Index
Index ® New Brunswick Innova 2000/2050 Shaker English (EN) Index Keypad ..............13 Accessories............11 Alarm ...........11, 22, 22, 22 Main illustration............9 Mains/power ............11 Maintenance ............25 Bearings ..............14 Manual conventions..........6 Measuring temperature ........23 Motor ..............14 Clamps..............32... - Page 37 Index ® New Brunswick Innova 2000/2050 Shaker English (EN) Universal power module ........11 Unpacking .............17 Using this manual............5 Voltages ..............17...
- Page 38 Index ® New Brunswick Innova 2000/2050 Shaker English (EN)
-
Page 39: Certificates
Certificates Declaration of Conformity The product named below fulfills the requirements of directives and standards listed. In the case of unauthorized modifications to the product or an unintended use this declaration becomes invalid. Product name: Innova® 2000 and 2050 including accessories Product type: Benchtop open air shaker Relevant directives / standards:... - Page 42 Evaluate Your Manual Give us your feedback. www.eppendorf.com/manualfeedback Your local distributor: www.eppendorf.com/contact Eppendorf AG · 22331 Hamburg · Germany eppendorf@eppendorf.com · www.eppendorf.com...