Advertisement
shaving time. This may vary according to your
beard growth and environmental temperature.
• Recommended ambient temperature for charging is
5 °C to 35 °C. The battery may not charge properly
or at all under extreme low or high temperatures.
Recommended ambient temperature for shaving
is 15 °C to 35 °C.
• Do not expose the appliance to temperatures
higher than 50 °C for extended periods of time.
• When the shaver will be connected to an electrical
outlet, it may take some minutes until the display
illuminates.
Shaver display
Charge status
The shaver display (5) shows the charge status of
the battery.
During charging: The battery symbol will blink.
(5090cc: The respective battery segment will blink.)
Fully charged (shaver is connected to an electrical
outlet): The battery symbol will light up for a few
seconds. (5090cc: All battery symbols will light up
for a few seconds.)
Low charge
The low-charge light
battery is running low. You should be able to finish
your shave. With switching off the shaver a beep
sound reminds of the low charge status.
Cleaning status
(models 5090cc/5070cc/5050cc only)
The cleaning indicator
needs to be cleaned in the Clean&Charge Station.
Travel lock
The lock symbol
lights up when the shaver has
been locked to avoid unintended starting of the
motor (e.g. for storing it in a suitcase).
Using the shaver
Press the on/off switch (4) to operate the shaver.
Tips for a perfect dry shave
For best results, Braun recommends you to follow
3 simple steps:
1. Always shave before washing your face.
2. At all times, hold the shaver at the right angle
(90°) to your skin.
3. Stretch your skin and shave against the direction
of your beard growth.
MultiHeadLock switch (head lock)
To shave hard-to-reach areas (e.g. under the nose)
slide the MultiHeadLock switch (3) down to lock the
shaver head. The shaver head can be locked in five
positions. To change position, move the shaver head
with your thumb and forefinger back or forth. It will
20
flashes red when the
lights up, when the shaver
(see fig. A)
automatically click into the next position.
To set it back into the pivoting position the
MultiHeadLock switch needs to be slid up again.
Models 5090cc/5070cc/5050cc: For automatic
cleaning in the Clean&Charge Station the head lock
should be released.
Long hair trimmer
To trim sideburns, moustache or beard press the
release button (8a) and slide the long hair trimmer
(6) upwards.
Shaving with the cord (models 5090cc/5070cc/
5050cc/5030s/5020s only)
If the shaver has run out of power (discharged), you
may also shave with the shaver connected to an
electrical outlet via the special cord set.
Travel lock
• Activation: By pressing the on/off switch (4) for
3 seconds the shaver is locked. This is confirmed
by a beep sound and the lock symbol
display. Afterwards the display turns off.
• Deactivation: By pressing the on/off switch for
3 seconds the shaver is unlocked again.
Manual cleaning of the shaver
• Switch the shaver on (cordless) and rinse the
shaver head under hot running water until all
residues have been removed. You may use liquid
soap without abrasive substances. Rinse off all
foam and let the shaver run for a few more
seconds.
• Next, switch off the shaver, press the release
button (2) to remove the Foil & Cutter cassette (1)
and let it dry.
• If you regularly clean the shaver under water, then
once a week apply a drop of light machine oil on
top of the Foil & Cutter cassette.
Alternatively, you may clean the shaver with a brush:
• Switch off the shaver. Remove the Foil & Cutter
cassette (1) and tap it out on a flat surface. Using
the brush, clean the inner area of the pivoting
head. Do not clean the cassette with the brush as
this may damage it!
Model 5040s only: The shaver should be cleaned
after each foam usage.
Clean&Charge Station
models 5090cc/5070cc/5050cc only
The Clean&Charge Station has been developed for
cleaning, charging, lubricating, disinfecting and
storing your Braun shaver.
12 Station power socket
in the
(s. fig. B/C)
Advertisement
