Advertisement
Quick Links
���������
Installation
B C
Manual
Part III:
Console Frame
Installation of the console
Operating conditions
Maintainance
B r o a d c a s t
Version 1.22/04 • English
analoge + digitale Tonstudiotechnik Karl Jüngling • Inh. Dipl.-Ing. Gerd Jüngling
Scholtwiese 4-6 • D45966 Gladbeck • Germany • Phone: 0(049) 2043 51061 • Fax: 0(049) 2043 56844
E-Mail: info@adt-audio.com • Internet: www.adt-audio.com www.broadcast-console.com
Advertisement
Related Manuals for adt-audio BC4
Summary of Contents for adt-audio BC4
- Page 1 B r o a d c a s t Version 1.22/04 • English analoge + digitale Tonstudiotechnik Karl Jüngling • Inh. Dipl.-Ing. Gerd Jüngling Scholtwiese 4-6 • D45966 Gladbeck • Germany • Phone: 0(049) 2043 51061 • Fax: 0(049) 2043 56844 E-Mail: info@adt-audio.com • Internet: www.adt-audio.com www.broadcast-console.com...
- Page 2 ��������� B r o a d c a s t Summary 1. Console Frames— 2. Installation of the console— 9 3. Operating conditions— 4. Maintainance— 11...
- Page 3 Chapter 3 contains general information about the assembly of the console, environmental considerations, the recommended maintenance, and a couple of remarks about the operation of the console to ensure a long and problem free lifespan. This manual concerns the stereo version of the BC4 broadcast console system, rev. 1.2...
- Page 4 ������� ����� ����� ���� �� ����� ���� ���� �� General informations ������ BC4 console frames are available in many ��� �������� different versions. Almost any frame size with an even number of module slots is possible. The maximum, overall width of a single frame is 3100 mm.
-
Page 5: Master Section
It is not possible to change this positi- on later. Groups A BC4 broadcast console can be equipped with 0, 4, 8, 12 or 16 groups. Since the standard mo- dules have a routing section for... - Page 6 The meter bridge is standard for all consoles. cial boards with these additional connectors and corresponding The BC4 frame uses the same meter bridge that connector panels are available. It is possible to use any mono is used for the BC3 on-air consoles, the SRC51 D Y N input modules with these slots with no limitations.
- Page 7 The meter is available in stereo and mono versions and fits into the meter bridge frame boards. It can be used Sources for all channels and masters of the BC4 system. A corre- sponding phase correlation meter is also available. All modules have configurable meter outputs. With in-...
- Page 8 The speaker fits into 4 meter bridge slots. devices can be mounted vertically and fit into the module grid. This series is best choice for use with the BC4 system. Additional devices Devices in standard cassette housings 190 x 40 mm (type 1113, The picture shows 1115 or 1119) must be installed horizontally.
- Page 9 The total weight of the entire system depends on the size of the frame and on the versions of modules. In any case, the total weight of a BC4 See the exploded view that contains marks for the lifting points of the broadcast console system will be between 100 kg/220 lbs (16 channel) frame.
-
Page 10: Operating Conditions
��������� B r o a d c a s t 3. Operating conditions are fixed to the side panels by a couple of screws. See the exploded view for the location of the fixing points and fix the panels on both sides of the frame. - Page 11 A BC4 console requires no regular maintenance. Service is only required, if there is a failure that makes repair necessary. Almost Cleaning all problems can be fixed by exchanging a defective module.
- Page 12 ��������� B r o a d c a s t type CRC3-36, brand CRC, Belgium. If you cannot get this oil, you can Screws order it from the factory. After a period of about 4 years, the power supply unit should be This cleaner contains a non-aggressive, non-permanent solvent that opened and all screws of the transformer and the prints should be re- dissolves hardened fat and grease effectively.