Special Servicing Tools And Aids; Special Servicing Tools - Stihl 020 T Service Manual

11.

Special Servicing Tools and Aids

11.1

Special Servicing Tools

No. Part Name
1 Locking strip for piston
2 Press sleeve
3 Assembly sleeve
4 Assembly hook
5 Assembly tube
6 Assembly drift
7 Clamping strap
8 Wooden assembly block
9 Carburetor and
crankcase tester
10 Vacuum pump
11 - Nipple
12 - Fuel line
16 Sealing plate
17 Test flange
18 Setting gauge
13 - Flange
14 - Pin
15 - Pan hd. screws
19 Stud puller M8
20 Installing tool 9
21 Puller
22 Service tool AS (set)
23 - Threaded sleeve
24 Screwdriver bit T27x125
25 Socket, 13 mm
26 Torque wrench
27 Torque wrench
28 Assembly tool
29 Installing tool
30 Assembly hook
31 Screwdriver T20x100
32 T-handle screwdriver
Q-SW 8x200
33 Crimping tool
34 Assembly stand
35 Screwdriver T27x150
36 Puller
37 - Jaws
38 Socket T20x125
Remarks:
1) Plastoform and DG screws must always be tightened with torque wrench.
2) Wrench has optical/acoustic signal.
STIHL 020 T
Part No. Application
0000 893 5903 Blocking the crankshaft
1129 893 2400 Installing oil seal and roller
bearing in crankcase
1129 893 4600 Protecting oil seal at
ignition side
5910 890 2800 Detaching springs from
clutch shoes
1117 890 0900 Attaching the brake spring
1114 893 4700 Fitting piston pin
0000 893 2600 Compressing piston rings
1108 893 4800 Fitting piston
1106 850 2905 Testing carburetor and crankcase
for leaks
0000 850 3501 Testing crankcase for leaks
0000 855 9200
1110 141 8600
0000 855 8106 Sealing exhaust port for
leakage test
1128 850 4200 For leakage test
1111 890 6400 Setting air gap between ignition
module and flywheel
1123 850 4200
0000 963 1008
9043 319 8100
5910 893 0501 Removing bar mounting stud
5910 890 2209 Fitting hookless snap rings
in piston
1116 893 0800 Removing flywheel
5910 007 2205 Separating crankcase halves
5910 893 2407
0812 542 2104 For IS screws (5 mm)
5910 893 5608 Crankshaft nut (ign. end) and clutch
5910 890 0301 Screw assemblies (0.5 to 18 Nm)
5910 890 0302
5910 890 0311 Screw assemblies (6 to 80 Nm)
5910 890 0312
1116 893 4800 Installing rewind spring
0000 890 2201 Flaring rope guide bush
5910 893 8800 Removing pickup body
5910 890 2301 For all IS-P screws (4 mm)
5910 890 2420 Carburetor nuts
5910 890 8210 Attaching connectors to
electrical wires
5910 850 3100 Holding saw for repairs
5910 890 2302 For all IS screws (5 mm)
0000 890 4400 Removing oil seals
0000 890 3700
0812 542 2041 Tightening IS-P screws (4 mm)
Rem.
1)
2)
1)
2)
57