Advertisement
Multi-Brand Control Feature
Advanced Connections
Multi-Brand Control Setup
Audio/Video connection
The Remote Control can be set to control some TV and Cable box/DSS functions.
If your TV has AUDIO IN and VIDEO IN terminals, you can connect your VCR
1
to them to receive higher quality picture and sound.
Find your TV and Cable Box/DSS Receiver Brand Code Number from those shown below.
2
Setup for TV control,
➛ hold down TV button,
➛ enter code with NUMBER keys.
Setup for Cable or DSS control,
➛ hold down DSS/CABLE button,
➛ enter code with number keys.
• If code number is 100 or greater,
➛ press 100 key, then other digits. E.g., press 100 - 0 - 2 for 102.
3
Confirm code entry,
➛ press POWER to turn your TV on or off.
• See table below for controllable functions in each mode.
• Repeat setup after remote battery replacement.
Notes
• Remote will not control every TV, cable box, or DSS made by the manufacturer listed.
If you get no response, your particular unit cannot be controlled. There are NO
additional codes for the products listed. If your product is not listed, then the remote is
not compatible with that product.
Using Multi-Brand Control
After remote is set up, you can select VCR, TV, or DSS/CABLE for the desired function.
Press VCR, or TV, or DSS/CABLE on the remote.
1
(Table below shows available unit buttons for each mode.)
Connect the VCR's VIDEO OUT jack to the TV's VIDEO IN jack.
Unit
VCR
TV
CABLE/ DSS
Mode
VCR
All
VOL UP/DOWN
2
VCR/TV, PLAY, STOP,
POWER, INPUT, number
Connect VCR's L/R AUDIO OUT jacks to the TV's L/R AUDIO IN jacks.
TV
EJECT, SAP/ Hi-Fi, DISPLAY,
keys, ENTER, CH UP/
FF, REW, PAUSE/SLOW,
DOWN, VOL UP/DOWN
REC, SPEED, CA/ZERO,
POWER, ENTER, NUMBER
CABLE/
COUNTER RESET, TAPE
VOL UP/DOWN
keys (except 100key),
3
DSS
POSITION
Set the VIDEO/TV selector of your TV (Monitor/Receiver) to "VIDEO."
CH UP/ DOWN
• Not all functions listed may be controllable.
Notes
• In TV or DSS/CABLE mode, it may be necessary to press ENTER after pressing
NUMBER keys for channel selection.
TV Brand Code Numbers
Panasonic ....................... 01, 02
Sylvania ................................ 05
JVC ....................................... 11
I I I I I With a Cable Box (VCR
Quasar ............................ 01, 02
Sharp .............................. 06, 07
Hitachi ................................... 12
RCA ...................................... 03
Mitsubishi ........................ 07, 13
Sony ...................................... 08
GE ......................................... 03
Toshiba ................................. 09
Samsung ............................... 14
Zenith .................................... 04
Sanyo .................................... 10
Gold Star ................... 15, 16, 17
Magnavox ............................. 05
Fisher .................................... 10
ANT
AUDIO
or
Cable Box Brand Code Numbers
CATV
Archer ............................... 05, 06, 01, 44, 63, 91, 126
Quest ............................................................... 05, 06
VIDEO
Cabletenna ................................... 01, 44, 63, 91, 126
Radio Shack ................................. 51, 44, 59, 75, 126
Cableview ................. 63, 44, 42, 30, 52, 04, 124, 126
RCA ................................................... 16, 17, 97, 109
IN 1
Century ......................................... 51, 44, 59, 75, 126
Realistic ........................................ 51, 44, 59, 75, 126
Recoton ........................................ 51, 44, 59, 75, 126
Citizen ...................... 63, 44, 42, 30, 52, 04, 124, 126
Curtis .............................................. 08, 09, 61, 53, 87
Regal ............ 14, 15, 28, 41, 102, 103, 104, 108, 130
Diamond ....................................... 01, 44, 63, 91, 126
Regency ........................................................ 28, 130
Drake ..................................................................... 67
Rembrandt ........................ 01, 32, 39, 42, 44, 63, 126
Eagle .......................... 13, 22, 58, 62, 20, 40, 26, 107
Salora .................................................................... 68
Eastern .......................................................... 28, 130
Samsung ........................................ 05, 32, 40, 42, 06
Scientific Atlanta ............................. 08, 09, 61, 53, 87
GC Brand ................. 63, 44, 42, 30, 52, 04, 124, 126
Gemini ........................................................... 04, 124
Sheritech ............................................................... 27
General Electric ............................................... 57, 01
Signal ............................................................ 26, 112
I I I I I Connect With Two Cable Boxes
General Instruments .. 01, 02, 03, 04, 34, 55, 83, 106,
SL Marx ................ 32, 40, 42, 06, 43, 44, 52, 63, 126
65, 67, 68, 115, 117, 118, 124, 91
Sprucer ............................................... 16, 17, 97, 109
Hamlin .......... 14, 15, 28, 41, 102, 103, 104, 108, 130
Standard Components .................. 32, 39, 42, 44, 126
Hitachi ................................................................... 31
Stargate .. 32, 40, 63, 44, 42, 30, 52, 04, 06, 124, 126
Jasco ............................................................. 04, 124
Sylvania ................................................................. 19
CABLE BOX
Jerrold ....................... 01, 02, 03, 04, 34, 55, 83, 106,
Teknika .................................................................. 74
65, 67, 68, 115, 117, 118, 124, 91
Telecaption .................................................... 77, 127
IN
OUT
Macom .................................................................. 31
Teleview ............................................... 32, 40, 42, 06
Magnavox ...................................................... 26, 112
Texscan ........................................................... 18, 19
Matsushita .......................................... 16, 17, 97, 109
Tocom ...................................... 33, 34, 01, 42, 66, 91
Toshiba ................................................................. 36
Movietime ......................... 32, 39, 42, 44, 126, 38, 40
NEC .......................................................... 38, 40, 32
Uniden Satelite ...................................................... 65
ANT
NOVAVISION ................................. 08, 09, 61, 53, 87
Unika ............................................ 01, 44, 63, 91, 126
or
2-Way Splitter
NSC .......................................................... 38, 40, 32
Universal ................................ 42, 43, 44, 52, 63, 126
Oak ........................................................... 46, 11, 129
Videoway ............................................ 07, 23, 50, 129
CATV
Oak Sigma ............................................... 46, 11, 129
Vid Tech ................................................................ 64
OUT 1
Vidtek .................................................................... 64
OUT 2
Panasonic .......................................... 16, 17, 97, 109
Philips ....................... 07, 13, 20, 23, 24, 50, 128, 129
Viewstar ..................... 13, 22, 58, 62, 20, 40, 26, 107
Pioneer ............................................................ 05, 06
Zenith ................................................. 07, 23, 50, 129
Pulsar ....................... 63, 44, 42, 30, 52, 04, 124, 126
DSS Brand Code Numbers
Toshiba ................................................................. 92
Panasonic ............................................................ 96
Hitachi/ Hughes .................................................... 93
RCA ..................................................................... 97
Magnavox/ Uniden 1 ............................................. 94
Sony ............................................................. 98, 105
Magnavox/ Uniden 2 ............................................. 95
• Due to changes in infra-red commands used by manufacturers, some brands have
Important
several codes. If your unit does not respond to the first code, please try the next one.
Notes
• Some TV, Cable Box and DSS Box brands require you to turn on the power manually.
- 2 -
MTS Broadcast/VHS Hi-Fi Stereo System
Connection
Make the Audio/Video Connection as shown on page 3.
• You can use a TV connected to Stereo amp and speakers instead of a Stereo TV.
TV
VCR
R
IN FROM ANT.
L
VCR
AUDIO OUT
TV
AUDIO OUT
VHF/UHF
R
R
AUDIO IN
L
R
VHF/UHF
OUT TO TV
L
VIDEO OUT
Receivable Broadcast Types
The following are possible audio broadcast types and on-screen displays.
VIDEO IN
The signal being received is indicated with an " " mark while the selected audio mode is
indicated with an arrow.
To display the broadcast signal being received,
➛ ➛ ➛ ➛ ➛ press DISPLAY*.
MTS Stereo and SAP broadcast
Multi-channel Television Sound Stereo (main language)
and Secondary Audio Program (sub language)
broadcasts are being received simultaneously.
Select STEREO or SAP audio mode.
MTS Stereo broadcast
Multi-channel Television Sound Stereo broadcast.
Select STEREO audio mode.
• If stereo broadcast is weak and display flickers, select
MONO audio mode for possibly better results.
SAP broadcast
Secondary Audio Program (sub language) broadcast.
Select SAP audio mode for the sub language.
Cable Box)
You Can
You Cannot
TV
• record
MONO broadcast
• view any
(including
scrambled
IN FROM ANT.
Normal monaural sound broadcast.
IN
OUT
channels.
R
scrambled)
R
CABLE BOX
channel.
AUDIO
L
L
VHF/UHF
OUT TO TV
IN
OUT
VIDEO
• use VCR
VHF/UHF
OUT
Remote
Control to
VCR
select
Audio Mode for Recording
channels
without using
Multi-brand
1
Press SAP/ Hi-Fi to display audio mode.
control feature.
(Display disappears after 5 seconds.)
2
You Can
You Cannot
Press SAP/ Hi-Fi
repeatedly to select
VCR
STEREO
• view channel
• record and view
SAP
desired mode.
MONO
both scrambled
other than
AUDIO
IN FROM ANT.
the one
• Refer to "Receivable
and
R
Broadcast Types"
unscrambled
selected for
L
VHF/UHF
any type of
above.
channels if
VIDEO
recording.
OUT TO TV
additional
• Arrow indicates selection.
TV
equipment is
IN 1
OUT
• do a Timer
added.
3
A/B Switch
IN
OUT
This connection
recording of
Do a recording.
R
a channel
CABLE BOX
AUDIO
requires: two
See p. 5 of "Basic Operations"
L
converter
unless you
IN
OUT
IN 1
IN 2
Instruction book.
VIDEO
select it at
boxes, an A/B
VHF/UHF
switch, and a 2-
the cable
box.
way splitter.
Notes
• Only tapes recorded in Hi-Fi stereo will playback with true stereo sound. Standard stereo tapes
will playback in monaural sound.
• To listen to Hi-Fi stereo playback, the VCR AUDIO (L/R) jacks must be connected to a stereo TV
or an external stereo amp and speakers. (See top of this page.)
• If tracking is adjusted during playback, Hi-Fi audio may revert to normal audio.
• Hi-Fi and normal audio playback volume level may differ.
*Important: If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
- 3 -
Timer Recording Using VCR Plus+ System
VCR Plus+ System is ...
This feature sets most items of a Timer Recording when you enter a PlusCode programming
number found in TV GUIDE and selected newspaper TV listings.
Initial Setup.....
To use VCR Plus+ system, clock and channels must be set (p. 4 of "Basic Operations" book).
Channel Setup.....
®
Equipped with
-TV Noise
Broadcast/ cable stations are assigned a VCR Plus+ (GUIDE CH) number. See the Channel
Reduction for true MTS
Listing (directory) page of TV GUIDE, etc. In the Channel Setup below, you will be entering your
reproduction.
®
-TV Noise
local channel number (RECEIVE CH) for each GUIDE CH number.
Stereo Amplifier
Example : if NBC's assigned GUIDE CH were 05, and your TV received NBC on channel 04, you
Reduction is required for good
would enter 04 across from GUIDE CH 05 in step 3 of "VCR Plus+ System Channel Setup".
R
R
stereo separation and audio
L
fidelity.
®
is a registered
AUDIO IN
R
VCR Plus+ System Channel Setup
trademark, and is licensed by
L
OUT TO TV
®
Technology Licensing.
For [VCR-TV] or [VCR-cable box-TV] connection only.
You'll need a local TV channel listing (e.g. TV
GUIDE) which includes the assigned VCR Plus+
numbers.
1
Press ACTION
VCR C / A CLOCK
CHANNEL
ANTENNA : CABLE
to display menu, and
AUTO SET
WEAK SIGNAL DISPLAY : OFF
Press
CABLE/DSS BOX SET UP
VCR Plus+ CH SET UP
to select CHANNEL.
SELECT :
EXIT
: ACT I ON
2
Press
VCR C / A CLOCK
CHANNEL
ANTENNA : CABLE
to select VCR Plus+ CH
AUTO SET
STOP
1 2 : 0 0AM
CH 02
WEAK SIGNAL DISPLAY : OFF
0 : 0 0 : 0 0
SET UP, and press
to
CABLE/DSS BOX SET UP
STEREO
SP
VCR Plus+ CH SET UP
set.
SAP
MONO
SELECT :
SET :
EXIT
: ACT I ON
3
Press
to move cursor
VCR C / A CLOCK
CHANNEL
GUIDE CH
RECEIVE CH
to right, press
to
01
--
enter number, press
02
--
STOP
1 2 : 0 0AM
CH 02
03
--
to set, press
to
0 : 0 0 : 0 0
STEREO
SP
scroll up/down.
SAP
MONO
• Repeat step 3 until list
VCR C / A CLOCK
CHANNEL
is complete.
GUIDE CH
RECEIVE CH
01
--
• Leave line blank if
02
--
03
--
station is not received
CLEAR : ADD/DLT
or if GUIDE and
SELECT :
SET:
STOP
1 2 : 0 0AM
CH 02
EXIT
: ACT I ON
RECEIVE CHs are the
0 : 0 0 : 0 0
same.
STEREO
SP
SAP
To Make Corrections,
MONO
press
and
to move to error, then
to
change, or ADD/DLT to erase number.
4
Press ACTION twice to end setup.
STOP
1 2 : 0 0AM
CH 02
0 : 0 0 : 0 0
Do normal Timer Record if...
STEREO
SP
• PlusCode number is not listed for program.
SAP
MONO
• program (e.g. sports event) may run over set stop time.
See page 6 of "Basic Operations" book to:
• cancel a timer recording in progress.
• review, replace, or clear program contents.
Important for DSS/Cable Box Users
• When recording via DSS, the receiver must be
Audio Mode for Playback
left on. When recording via cable or antenna,
DSS receiver must be off.
1
Start playback.
• When recording via a cable box, leave box on
and tuned to channel to be recorded.
See p. 5 of "Basic Operations"
Instruction book.
Tape Operation
2
Press SAP/ Hi-Fi to display audio mode.
(Display disappears after 5 seconds.)
Repeat Play
3
Press SAP/ Hi-Fi
Set to playback a recording over and over.
repeatedly to select
1
H I F I : L / R
Press ACTION to display menu.
H I F I : L
desired mode.
H I F I : R
NORMAL
• Select "HIFI(L/R)"
2
Press
to select
VCR
C / A
CLOCK
CH
REPEAT PLAY
:OFF
or "HIFI(L)" or
REPEAT PLAY and
REMOTE WARNING
:ON
AUTO SHUT- OFF
:OFF
"HIFI(R)" to listen to
press
to set ON or
IDIOMA/LANGUE : ENGLISH
stereo recordings in
VCR' S OUTPUT CH
:3
OFF.
• Arrow indicates
stereo sound.
SELECT :
SET :
ON : Play repeats at tape end
selection.
Select "NORMAL"
EXIT
: ACT I ON
or if unrecorded portion
for monaural sound.
over 30 sec. is detected.
3
Press ACTION to return to normal screen.
- 4 -
Tape Operation
marks start and end points of
commercials within recordings over 15 minutes
played back so that commercial blocks are
long. The VCR automatically advances through
advanced through automatically or manually.
marked commercials at high speed. Or, you may
set to manual. Because stations broadcast
1
VCR
C / A
differently, the effectiveness of this feature may
REPEAT PLAY
REMOTE WARNING
vary. See bottom of page for answers to
AUTO SHUT- OFF
IDIOMA/LANGUE : ENGLISH
commonly asked questions about this feature.
VCR' S OUTPUT CH
SELECT :
Marking
EXIT
: ACT I ON
2
With C/A RECORD: ON, the VCR auto rewinds
VCR
C / A
VCR Plus+ System Programming
SET UP COMMERCIAL ADV.
after a recording is made and marks start and end
C/A RECORD
C/A PLAYBACK
points of all detected commercial blocks.
1
Press PROG/VCR+ button to display PROGRAM.
After marking, the tape is returned to end of
recording. Commercials are not erased.
2
Press
to select
VCR Plus+
PROG.
LIST
SELECT :
EXIT
: ACT I ON
display VCR Plus+
1
ENTER PLUSCODE NUMBER
VCR
C / A
CLOCK
CH
Press ACTION*
screen.
REPEAT PLAY
:OFF
to display MENU.
3
-
REMOTE WARNING
:ON
VCR
C / A
AUTO SHUT- OFF
:OFF
SET UP COMMERCIAL ADV.
USING 0 - 9 KEYS
IDIOMA/LANGUE : ENGLISH
C/A RECORD
VCR' S OUTPUT CH
:3
C/A PLAYBACK
3
Press NUMBER keys
VCR Plus+
PROG.
LIST
SELECT :
to enter PlusCode
EXIT
: ACT I ON
ENTER PLUSCODE NUMBER
SELECT :
number and press
2
Press
to select
EXIT
: ACT I ON
VCR
C / A
CLOCK
CH
1
PROG/VCR+ button
SET UP COMMERCIAL ADV.
C/A and display SET UP
C/A RECORD
:ON
• If the PlusCode
AUTO : VCR will automatically advance through
to set.
C/A PLAYBACK
:AUTO
COMMERCIAL ADV.
number entered
marked commercial blocks recorded on
To Make Corrections,
begins with "0," skip
the tape and then resume playback.
press
repeatedly
to step 5. Display in
SELECT :
to delete number, then
EXIT
: ACT I ON
step 4 will not appear.
MANUAL : VCR will advance through
repeat step 3.
3
Press
to select C/A
VCR
C / A
CLOCK
CH
4
Press
to select
SET UP COMMERCIAL ADV.
VCR Plus+
PROG.
LIST
RECORD and press
C/A RECORD
:ON
C/A PLAYBACK
:AUTO
ONCE, DAILY
to set "ON" or "OFF".
ONCE
DAILY(MON-FRI)
(MON~FRI), or WEEKLY
WEEKLY
record frequency and
press PROG/VCR+
SELECT :
SET :
EXIT
: ACT I ON
SELECT :
END
: PROG
button to set.
4
ON: Timer recording, VCR Plus+ System, and One
Press ACTION again to return to normal screen.
5
Press
to change
Touch recordings are marked automatically.
VCR Plus+
PROG.
LIST
DATE
START
STOP
CH
record speed and
• When timer is used to
13 SAT 2:20P 3:20P 02
THE VCR IS WAITING TO
press
to set.
Notes
MARK COMMERCIALS IN THE
record two consecutive
TODAY
PROGRAM YOU RECORDED.
SLP
SELECT RECORD SPEED
Press PROG/VCR+
shows (same channel),
• The mode set in step 3 remains unless a
button to end program.
greater accuracy can be
SELECT :
SET:
power outage occurs in which case the factory
MARKING
END
: PROG
NOW
: PRESS 1
obtained by programming
setting will be restored.
LATER
: PRESS 2
each show separately.
6
Press PROG/VCR+
CANCEL
: PRESS ACTION
VCR Plus+
PROG.
LIST
• If playback is started in the middle of a
DT START
STOP
CH SPD
button again to exit.
13
2 : 00 P
3 : 20P 02 SLP
When STOP is pressed during normal recording,
commercial, only a single commercial is
-- -- : -- -- : --
--
--
-- -- : -- -- : --
--
--
• Press ADD/DLT
press :
shown, or a single commercial is longer than 1
-- -- : -- -- : --
--
--
to delete the program.
a) 1 key (NOW) ➛ to mark now.
minute, a commercial may not be skipped.
CANCEL : ADD / DLT
SELECT :
SET :
"NOW MARKING COMMERCIALS" appears.
Press FF to quickly advance through the
EXIT
: PROG
b) 2 key (LATER) ➛ to mark after power is
commercial.
7
Press POWER off to set timer recording.
turned off. (If tape is rewound and another
• Part of a recorded program may be skipped
("TIMER" lights on Multi Function Display.)
recording is started before power is turned off,
over if the program portion between
correct marking may not occur.
commercials is less than one minute or there
Notes
c) ACTION (CANCEL) ➛ marking is canceled.
are frequent dark and quiet scenes in the
• Do not overlap program times.
program. To correct, press PLAY during the
OFF : The VCR will not mark commercials.
• See "Important for DSS/Cable Box Users" left.
skip, rewind tape to just prior to where skipping
Select when editing or dubbing a tape, or
• Make each entry within 1 minute or VCR
started, then press PLAY again for normal
when opting not to use this feature.
exits setup.
playback. When the end of the commercials is
• Once VCR Plus+ channel setup is done,
4
Press ACTION again to return to normal screen.
detected, auto advance will resume.
channels stay in memory. If there's a power
outage, channel setup may be lost. Please
The most commonly asked questions about
are answered below.
do channel setup again.
Answer
Question
• Obtain unlisted PlusCode numbers by
calling 1 - 900 - 454 - 7587. Call costs about
How fast does the VCR advance through
The VCR advances through a 3-minute commercial block in about 8 to 12
commercials?
seconds if the tape speed is SLP. In SP, it takes about 25 to 35 seconds.
$.95 per minute.
Are commercials advanced through only when I
Yes. The commercials are not marked until after the recording is
playback a recording?
finished.
Are commercials still recorded on the tape in
Yes. By setting the C/A PLAYBACK to MANUAL, see top of this
case I choose to view them sometime?
page, you can view or advance through commercials as desired.
Zero Search
Does
work in all recording
Yes.
speeds?
To quickly return to a specified tape location.
Does the VCR advance through commercials
Yes. As long as C/A PLAYBACK is set to AUTO, see top of this page,
1
Press DISPLAY during play to display
each time I playback tapes which were
the VCR should advance through commercials each time the tape is
Counter.
recorded using
?
played back.
2
Press RESET
After marking commercials, does the VCR stop at
The tape stops at the end of the recording so that any additional
PLAY
1 2 : 0 0AM
0 : 0 0 : 0 0
the end of the tape, or rewind to the beginning?
timer recordings can be performed.
SP
COUNTER at desired
position to reset to
Can I play my
recordings in
Yes.
marked recordings will play in non-
"0:00:00".
non-
VCRs?
VCRs, but commercials will not be advanced through.
No. If the interval between 2 or more timer programs is not sufficient
Does the marking process interfere with other
to mark the recording, marking will be done after all recordings are
programmed recordings?
complete and the power goes off.
3
Continue to record, playback, etc.
What happens if I cancel the marking in
Marking will be resumed when the VCR's power is turned off as
4
progress so I can use the VCR?
long as the tape has not been ejected.
Press STOP.
What if part of my program is advanced through
Please see the 3rd note on top of this page.
5
Press CA/ZERO in
REW
1 2 : 3 0AM
CH 02
along with the commercials?
0 : 30 : 30
Stop mode to start
SP
Additional Notes:
ZERO SEARCH.
• Because of the various ways in which commercials are broadcast, the VCR may not be able to recognize all
• Unit will go into FF
commercials.
or REW mode and
• If a timer recording is scheduled for the middle of the night, please be aware that the VCR will make some noise
STOP
1 2 : 3 1AM
CH 02
as it rewinds and fast forwards the tape while marking commercials.
stop at the last point
0 : 0 0 : 0 0
SP
the Counter was set
and
are registered trademarks of SRT, Inc.
to 0:00:00.
A Jerry lggulden invention licensed in association with Arthur D. Little Enterprises, Inc.
U.S.Pat. No. 5,333,091; 5,692,093; 5,696,866 other patents pending
- 5 -
- 6 -
Tape Operation
Playback
Playback
marked recordings can be
helps you locate certain parts of
To Search for Preview.
prerecorded movies (rented or purchased).
The feature works in two ways.
You can override the operation of
SEARCH FOR PREVIEWS
• You can go to the beginning of the movie.
Press ACTION
mode by pressing SEARCH/ M/A SKIP during
CLOCK
CH
• You can skip from one preview to the next.
:OFF
to display MENU.
works only on tapes recorded in
tape searching.
:ON
:OFF
SP speed with the record tab removed.
searching the tape past each preview and then
:3
1
reversing back to the start of the detected
Insert a tape without record tab.
preview. While the tape is reversing back, if
2
Press SEARCH/ M/A
SEARCH
SEARCH/ M/A SKIP is pressed,
INDEX
PROG. END
MOVIE
SKIP to display
will begin searching for the
Press
to select C/A
CLOCK
CH
ENTER INDEX NUMBER :1
SEARCH.
USING 1- 9 KEYS
next preview. While searching for the next
and display SET UP
:ON
FORWARD SEARCH :FF
preview, if you see the start of a preview which
:AUTO
COMMERCIAL ADV.
REVERSE SEARCH :REW
NEXT
:SEARCH M/A SK I P
you wish to watch, press SEARCH/ M/A SKIP
EXIT
:STOP
and
will immediately reverse
3
Press SEARCH/ M/A
back to the start of that preview, instead of
SEARCH
INDEX
PROG. END
MOVIE
SKIP twice to select
searching further past the preview start point.
Press
to select C/A
GO TO START MOVIE
CLOCK
CH
MOVIE and press
GO TO PREVIEW
Once the VCR is playing a preview, press
PLAYBACK and press
to select GO TO
:ON
SEARCH START : FF
SEARCH/ M/A SKIP to advance to the next
:AUTO
to set "AUTO" or
SELECT
:
START MOVIE or GO
preview, long commercial or the start of the
"MANUAL".
EXIT
: SEARCH M/A SK I P
TO PREVIEW.
movie (whichever is next).
Select "GO TO START MOVIE," if you want to
SET :
1
advance directly to beginning of the movie.
Start preview searching.
➛ continue with step 4.
1) In step 3 at left, select Go To PREVIEW.
Select "GO TO PREVIEW," if you want to view
2) Press FF.
the first (next) preview.
➛ go to "To Search for Preview" at right.
• If you want to playback, press PLAY.
4
Press FF to start
SEARCH
commercials only when CA/ZERO is
When a preview is detected, VCR
INDEX
PROG. END
MOVIE
searching.
pressed. Playback will resume when
will start playback.
SEARCHING FOR START
the end mark of a commercial block is
OF MOVIE
• To cancel, press
found, or a new recording or blank
STOP.
2
Start next preview searching.
portion is detected, or after 8 minutes.
CANCEL : STOP
Press SEARCH/ M/A SKIP.
When the movie is found...
• To cancel, press STOP.
5
Press PLAY to start
SEARCH
INDEX
PROG. END
MOVIE
playback.
THE MOV I E I S READY
• To cancel, press
START : PLAY
STOP.
CANCEL : STOP
Search System
For each recording, an invisible index mark is placed on the tape. A program index and
information are also included for timer recordings. These marks are used to access or
scan recordings.
Index Search
Program End Search
1
SEARCH
Press SEARCH/ M/A
Locates end point of recording for continuity.
INDEX
PROG. END
MOVIE
SKIP to display
1
ENTER INDEX NUMBER :1
Press SEARCH/ M/A SKIP twice to
USING 1- 9 KEYS
SEARCH in Stop or Play
mode, and then press
display SEARCH in Stop or Play mode.
FORWARD SEARCH :FF
REVERSE SEARCH :REW
NUMBER keys to select
2
Press FF on the
NEXT
:SEARCH M/A SK I P
SEARCH
EXIT
:STOP
recording number.
INDEX
PROG. END
MOVIE
remote to start
• To calculate number,
PROGRAM END
see below.
SEARCH START :FF
SEARCH.
Press FF or REW on
NEXT
:SEARCH M/A SK I P
• To cancel, press
EXIT
:STOP
the remote to start
STOP or PLAY.
search.
Examples of Program End Search.
Examples of Program End Search.
2
INDEX SEARCH
Play begins at search
end. To search forward
Fig. 1
or back 1 index, press
Program 1
Program 2 or BLANK
FF or REW on the
remote or VCR while
the current tape position
FORWARD SEARCH :FF
REVERSE SEARCH :REW
Press SEARCH button
screen left is displayed
End Point
FF
(10 sec.).
Fig. 2
works in SP, LP, and SLP.
• To cancel, press
STOP or PLAY.
Program 1
BLANK
Program 2
the current tape position
To Calculate Index Number
Press SEARCH button
FF
Example 1:
Fig. 3
To go to rec. 2 from rec. 4, enter 3 and press REW.
the current tape position
Press SEARCH button
Program 1
BLANK
1
2
3
4
5
6
7
FF
Example 2:
End Point
To go to rec. 6 from rec. 2, enter 4 and press FF.
Upon locating end point,
1
2
3
4
5
6
7
➛ search continues 7 sec. past end point,
NOTE:
indicates start points of each recording.
➛ tape rewinds to 10 sec. before end point,
➛ tape plays to end point and stops.
Note
• If Index Search is started very close to an
Notes
index mark, that index mark may not be
counted in the search.
• If Program End Search is started very close
to an index mark, that mark may be skipped
*Important:
If a remote control button does not work when pressed,
over.
• To cancel, press PLAY or STOP.
press the VCR button on the remote and try the button again.
- 7 -
works by
BLANK
End Point
Program 2
If search
exceeds a few
seconds in
BLANK area.
Advertisement
