1. Manuals
  2. Brands
  3. Brovision Manuals
  4. Network Hardware
  5. WH-N5204-P4
  6. Quick operation manual

Brovision WH-N5204-P4 Quick Operation Manual

Hide thumbs Also See for WH-N5204-P4:
Table of Contents

Advertisement

Quick Links

See also: User Manual
Network Video Recorder
Quick Operation Guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WH-N5204-P4 and is the answer not in the manual?

Questions and answers

Related Manuals for Brovision WH-N5204-P4

Summary of Contents for Brovision WH-N5204-P4

  • Page 1 Network Video Recorder Quick Operation Guide...

  • Page 2: Table Of Contents

    Wiring of Alarm Output ........................... 10 Using of Alarm Connectors ........................10 Controller Connection ..........................11 Specifications ..............................12 Specifications of WH-N5204-P4 & WH-N5208-P8 ................12 Specifications of WH-N5216-P16 ......................13 HDD Storage Calculation Chart ........................14 Accessing by Web Browser ..........................15 Logging In ..............................

  • Page 3: Nvr Pre-Installation

    This manual is applicable to the models listed in the following table. Series Model Type WH-N52xx WH-N5204-P4 Network Video Recorder WH-N5207-P8 WH-N5216-P16 NVR Pre-Installation These series NVR are highly advanced surveillance equipment that should be installed with care. Please take into consideration the following precautionary steps before installation of the NVR.
  • Page 4 Quick Operation Guide of Network Video Recorder 3. Connect the power cable to the HDD. 4. Place the HDD on the bottom of the device and then fasten the screws on the bottom to fix the HDD.

  • Page 5: Front Panel

    Quick Operation Guide of Network Video Recorder Front Panel WH-N5204-P4 & WH-N5208-P8 Front Panel of 4ch/8ch Description of Front Panel Name Function Description POWER: the POWER indicator turns green when NVR is powered up. READY: The indicator light is green when the device is running normally.
  • Page 6 Quick Operation Guide of Network Video Recorder Name Function Description Enter numeral “6”; Enter letters “MNO”; 6/MNO/PLAY: Playback, for direct access to playback interface. Enter numeral “7”; Enter letters “PQRS”; 7/PQRS/REC: Open the manual record interface. Enter numeral “8”; Enter letters “TUV”; 8/TUV/PTZ: Access PTZ control interface.
  • Page 7 Quick Operation Guide of Network Video Recorder WH-N5216-P16 Name Function Description POWER ON/OFF Power on/off switch. USB Interface Connect to USB mouse or USB flash memory. IR Receiver Receiver for IR remote control. devices. POWER Power indicator lights in green when DVR is powered up. READY Ready indicator is normally green, indicating that the DVR is functioning properly.
  • Page 8 Quick Operation Guide of Network Video Recorder In PTZ Control mode, the F1 button can be used to zoom in (zoom+) the PTZ camera; The F2 button can be used to cycle through tab pages. Enter numeral “4”; Enter letters “GHI”; 4GHI/ESC Exit and back to the previous menu.
  • Page 9 Quick Operation Guide of Network Video Recorder Rear Panel WH-N5204-P4 WH-N5208-P8 Item Description Power Supply 48V DC power supply for 4ch NVR and AC 100~240V for 8ch and 16ch NVR Audio In RCA connector for audio input. HDMI Interface HDMI video output connector.
  • Page 10 Quick Operation Guide of Network Video Recorder Item Description RS-232 Interface Connector for RS-232 devices. DB9 connector for VGA output. Display local video output and menu. HDMI HDMI video output connector. eSATA (Optional) Connects external SATA HDD, CD/DVD-RM. LAN Interface 1 network interface Termination Switch RS-485 termination switch.

  • Page 11: Peripheral Connections

    Quick Operation Guide of Network Video Recorder Peripheral Connections Wiring of Alarm Input The alarm input is an open/closed relay. To connect the alarm input to the device, use the following diagram. If the alarm input is not an open/close relay, please connect an external relay between the alarm input and the device.

  • Page 12: Controller Connection

    Quick Operation Guide of Network Video Recorder 3. Connect pluggable block back into terminal block. Controller Connection To connect a controller to the NVR: 1. Disconnect pluggable block from the KB terminal block. 2. Unfasten stop screws from the KB D+, D- pluggable block, insert signal cables into slots and fasten stop screws.

  • Page 13: Specifications

    Quick Operation Guide of Network Video Recorder Specifications Specifications of WH-N5204-P4 & WH-N5208-P8 Model WH-N5204-P4 WH-N5208-P8 IP video input 4-ch 8-ch Video/Audio Two-way audio 1-ch, RCA (2.0 Vp-p, 1kΩ) input input Incoming bandwidth 25Mbps 50Mbps Network Outgoing bandwidth 80Mbps Remote connection...

  • Page 14: Specifications Of Wh-N5216-P16

    Quick Operation Guide of Network Video Recorder Specifications of WH-N5216-P16 Model WH-N5216-P16 IP video input 16-ch Video/Audio input 1-ch, BNC (2.0 Vp-p, 1kΩ) Two-way audio Incoming bandwidth 100Mbps Network Outgoing bandwidth 240Mbps Remote Connection 5MP /3MP /1080P /UXGA /720P /VGA /4CIF /DCIF /2CIF /CIF Record resolution /QCIF Main stream: 25 fps (P) / 30 fps (N)

  • Page 15: Hdd Storage Calculation Chart

    Quick Operation Guide of Network Video Recorder HDD Storage Calculation Chart The following chart shows an estimation of storage space used based on recording at one channel for an hour at a fixed bit rate. Bit Rate Storage Used 128K 160K 192K 224K...

  • Page 16: Accessing By Web Browser

    Quick Operation Guide of Network Video Recorder Accessing by Web Browser Logging In You can get access to the device via web browser. Open web browser, input the IP address of the device and then press Enter. The login interface appears. Input the user name and password, and click the Login button.

  • Page 17: Recording

    Quick Operation Guide of Network Video Recorder Interface Introduction Name Description Displays the list of channels and the playing and recording status of each channel. Channel List The stream type can be switched by clicking the icon before the channel name: stands for main stream and for sub-stream.
  • Page 18 Quick Operation Guide of Network Video Recorder 3. Check the checkbox of Enable Schedule to enable recording schedule. 4. Choose the day in a week to configure scheduled recording. 5. Click Edit to edit record schedule. 1) Configure All Day or Customize Record: ...

  • Page 19: Playback

    Quick Operation Guide of Network Video Recorder Playback Interface Introduction Name Description Channel List Displays the list of channels and the playing status of each channel. Playback Window Displays the image of channel. Play Control Bar Play control operations are supported. Time Line Displays the time bar and the records marked with different colors.

  • Page 20: Log

    Quick Operation Guide of Network Video Recorder Area Description Area Description Full screen Transcoded playback Reverse playback Window division You can drag the progress bar with the mouse to locate the exact playback point. You can also input the time in the textbox and click button to locate the playback point.

  • Page 21: Menu Operation

    Quick Operation Guide of Network Video Recorder Menu Operation Menu Structure The menu structure of the WH-N52xx Series NVR: Startup and Shutdown Proper startup and shutdown procedures are crucial to expanding the life of the NVR. To start your NVR: 1.

  • Page 22: Live View

    Quick Operation Guide of Network Video Recorder Live View Some icons are provided on screen in Live View mode to indicate different camera status. These icons include: Live View Icons In the live view mode, there are icons at the upper-right corner of the screen for each channel, showing the status of the record and alarm in the channel, so that you can find problems as soon as possible.
  • Page 23 Quick Operation Guide of Network Video Recorder The online cameras with same network segment will be displayed in the camera list. Click the button to add the camera. Or you can click the One-couch Adding button to add all the online IP cameras. The added camera is marked in white while the camera has not been added is marked in yellow.

  • Page 24: Recording

    Quick Operation Guide of Network Video Recorder You can edit the IP address, protocol, management port, and other information of the IP camera to be added. Click Add to add the camera. (For the encoders with multiple channels only) check the of Channel No.

  • Page 25: All-Day Recording

    Quick Operation Guide of Network Video Recorder window when you click on it. Click the icon to enable the record, and the icon turns to . And click icon to disable the record, then the icon turns to All-day Recording Steps: 1.

  • Page 26: Backup

    Quick Operation Guide of Network Video Recorder Front Panel: press PLAY button to play back record files of the channel under single-screen live view. Under multi-screen live view, record files of the selected channel will be played back. Pressing numerical buttons will switch playback to related channels during playback process. 2.
  • Page 27 Quick Operation Guide of Network Video Recorder 2. Enter Export interface, choose backup device and click Export button to start exporting. 3. Check backup result. Choose the record file in Export interface and click button to check it.

This manual is also suitable for:

Wh-n5207-p8Wh-n5216-p16

Table of Contents