Echo GT-220ES Service Data

Advertisement

10-21P-02
SERVICE DATA
TRIMMER/BRUSHCUTTER
INTRODUCTION
We are constantly working on technical im-
provement of our products. For this reason,
technical data, equipment and design are
subject to change without notice. All speci-
fications, illustrations and directions in this
SERVICE DATA are based on the latest
products information available at the time of
publication.
INDEX
GT-220ES, SRM-220ES
(Serial nember : 36000001 and after)
STAGE
(Serial nember : 37000001 and after)
CONTENTS
1 SERVICE INFORMATION .............................. 2
1-1 Specifi cation ............................................... 2
1-2 Technical data ............................................. 3
1-3 Torque limits................................................ 4
1-4 Special repairing materials ......................... 4
1-5 Service limits............................................... 5
1-6 Special tools ............................................... 6
2-1 General adjusting rules ............................... 7
2-3 Adjusting carburettor................................... 8
Reference No.
R E V I S E D :
1
1
page
10-21P-02
2 0 0 9 0 1
ISSUED: 200705

Advertisement

Table of Contents
loading

Summary of Contents for Echo GT-220ES

  • Page 1: Table Of Contents

    GT-220ES, SRM-220ES 10-21P-02 SERVICE DATA TRIMMER/BRUSHCUTTER GT-220ES SRM-220ES (Serial nember : 36000001 and after) STAGE MODEL (Serial nember : 37000001 and after) INTRODUCTION CONTENTS page We are constantly working on technical im- 1 SERVICE INFORMATION ......2 provement of our products. For this reason, 1-1 Specifi...
  • Page 2: Gt-220Es

    GT-220ES SERVICE INFORMATION SRM-220ES 1 SERVICE INFORMATION 1-1 Specifi cations Model GT-220ES SRM-220ES (L) SRM-220ES (U) Dimensions Length* mm(in) 1460 (57.4) 1760 (69.3) Width mm(in) 320 (12.6) 345 (13.5) 655 (25.7) Height mm(in) 575 (22.6) 320 (12.6) 420 (16.5) Dry weight* kg(lb) 4.4 (9.7)
  • Page 3: Technical Data

    GT-220ES SRM-220ES SERVICE INFORMATION 1-2 Technical data Model GT-220ES SRM-220ES (L) SRM-220ES (U) Engine Idling speed r/min 2600 - 3400 Wide open throttle speed r/min 7000 - 8000* 8000 - 9700* 9500 - 11500** Clutch engagement speed r/min 3500 - 4100...
  • Page 4: Torque Limits

    GT-220ES SERVICE INFORMATION SRM-220ES 1-3 Torque limits Descriptions Size kgf•cm N•m in•lbf Starter Starter case 14 - 28 1.4 - 2.8 12 - 24 system Ignition Ignition coil 30 - 50 3 - 5 26 - 45 system Fan cover...
  • Page 5: Service Limits

    GT-220ES SRM-220ES SERVICE INFORMATION 1-5 Service limits 5K268 5K228A 5K229A 5K230 5K016 5K042 5K269 5K231A 5K171 5K071A Description mm (in) Cylinder bore When plating is worn and aluminium can be seen Piston outer diameter Min. 32.10 (1.264) Piston pin bore Max.
  • Page 6: Special Tools

    GT-220ES SERVICE INFORMATION SRM-220ES 1-6 Special tools Part Number Description Used for: 897801-33330 Tachometer PET-1000 Measuring engine speed 363018-00310 Washer Installing crankcase oil seal of starter side 895610-79920 L-hex wrench (4 mm) Removing and installing hex. socket bolts (M5) 897603-23030...
  • Page 7: Carburettor Adjustment Procedure

    3. Turn Idle adjust screw (E) anticlockwise until screw tip just touches throttle plate (F). Then turn it in clockwise 1 1/2 (GT-220ES), 2 1/2 (SRM-220ES) turns. NOTE : Initial carburettor setting (Idle adjust screw, Idle and Hi speed mixture needles) shown here is to start the engine after restoration or carburettor change.
  • Page 8: Adjusting Carburettor

    2,600 to 3,400 r/min, and WOT en- gine speed ranges from 7,000 r/min to 8000 r/min on GT-220ES, 8,000 r/min to 9,700 r/min on SRM- 220ES with nylon line head, 9,500 r/min to 11,500 r/min on SRM-220ES with metal blade. Make sure the cutter does not rotate when engine is idling.

This manual is also suitable for:

Srm-220es

Table of Contents