Table of Contents
Advertisement
Quick Links
adt-audio
Installation
SRC
Manual
5 1
Part I:
General Information
Power Supply Units
Audio Installation
Version 1.5/13 • English
analoge + digitale Tonstudiotechnik Karl Jüngling • Inh. Dipl.-Ing. Gerd Jüngling
4-6 Scholtwiese • Gladbeck • 45966 • NRW • Germany • Phone: 0049 2043 51061 • Fax: 0049 2043 56844
E-Mail: info@adt-audio.com • Internet: www.adt-audio.com www.broadcast-console.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for adt-audio SRC 51
Summary of Contents for adt-audio SRC 51
-
Page 1: Src 5
Version 1.5/13 • English analoge + digitale Tonstudiotechnik Karl Jüngling • Inh. Dipl.-Ing. Gerd Jüngling 4-6 Scholtwiese • Gladbeck • 45966 • NRW • Germany • Phone: 0049 2043 51061 • Fax: 0049 2043 56844 E-Mail: info@adt-audio.com • Internet: www.adt-audio.com www.broadcast-console.com... -
Page 2: Table Of Contents
Summary Preface..............3 2. Audio Installation in the Studio... 14 1. Power supply........... 4 2.1 Grounding............14 1.1 Power supply units........5 2.2 Common grounding problems...... 16 1.2 Power supply installation......6 2.3 Cables............17 1.3 Fail-safe Power Supply........8 2.4 Planning of the installation...... -
Page 3: Adt-Audio
Preface This manual contains all the information that is necessary to prepare and plan the installation of the mixing console and accessory components. Please, read this manual carefully. We point out common mistakes and problems that are connected with the installation and provide suggestions to avoid such problems. -
Page 4: Power Supply
1. Power supply 1.1 Power supply units unit UPS10 is used. In addition, the UPS25 of the 5MT series of Three different power supply units are available, the UPS1000, consoles can be adapted since all the required voltages are the UPS10 and UPS25. -
Page 5: Power Supply Units
240 V with the 230 V version and in steps of 5 V from 100 to 120 V with ab Werk normalerweise auf 230 V geklemmt the 115 V version. The minimum mains voltage depends on this settings. 240V... -
Page 6: Power Supply Installation
For fail-safe operation a second, identical power supply and an additional cover plate, take care that the distance between the top of the unit and crossover device are used. See the chapter below for details. the additional cover plate is at least 5 cm / 2”. - Page 7 The terminals for the primary voltage settings are clearly marked inside is eventually the same, as it depends not on the capacity of the power the power supply unit either on the mains transformer for the UPS1000 supply unit but the current consumption of the console.
-
Page 8: Fail-Safe Power Supply
C1750 cross over units are equipped with Shottky diodes mains voltage too, is much too high. This results in a high voltage across with very low drop out voltage to keep voltage drop and power the voltage regulator, therefore in a high power that causes higher heat dissipation of the failsafe system as low as possible. -
Page 9: The Mains Power Supply Of Audio Systems
1.4 The Mains Power Supply of Audio Systems conditions. Additional ventilation is not required and the installation is not critical as far as the airflow is concerned. Connectors ONLY QUALIFIED PERSONNEL SHOULD BE ALLOWED TO INSTALL All connectors are mounted on the rear panel of the device. The mains AND/OR MODIFY HAZARDOUS VOLTAGE, ELECTRICAL SYSTEMS. - Page 10 RF noise. Even though the input filters of the console’s power supply of these considerations is that a separate, current free conductor must units and an additional, totally separated screen winding of the mains be used for ground. If the mains supply line is implemented as a five-line transformer will block these disturbances as far as the console’s DC supply...
- Page 11 This principle should be used to connect the electric ground and protective allows easier control over the power dissipation but it produces high- ground of all devices in the studio with high cross section cable.
-
Page 12: Power Supply Connections
Inrush current Cable length Since the power supply units of the SRC51 consoles have a very high The cables that are usually used are high cross section multicore cables inrush current, precautions are necessary that concern the mains fuses. -
Page 13: The Pinning Of The Power Supply Plugs
In this case, we use an AUDIO POWER CONNECTORS IN CONSOLE, additional connector for the two high current audio lines only. Using a 26 line / 1.5 mm2 cable means that 6 1.5 mm2 lines can be used POWER-SUPPLY AND CROSS-OVER UNITS for the 4 high current audio lines in parallel. -
Page 14: Audio Installation In The Studio
All screen pins of all the audio connector of any adt-audio lines in the studio are connected to the console. If this ground installation... - Page 15 WE ADVISES THAT YOU CONSULT A QUALIFIED ELECTRICIAN REGARDING THE INSTALLATION OF ANY NEW ELECTRICAL However, the problem with this principle is that electric safety has the SUPPLY, OR THE MODIFICATION OF AN ExISTING SUPPLY. BY NO highest priority.
-
Page 16: Common Grounding Problems
For the realization, the main ground node, which in this case can be the Video central ground point of the building, or a separate earthing electrode, or This is the basic problem of any TV studio. Since all video connections are... -
Page 17: Cables
There is only one possible way to deal with these problems. After the the skin depth is approx. 0.3 mm. With audio cables that usually have a installation is ready, tested and clean, check if there is any degradation diameter in the range of 0.2 to 0.4 mm this means, that there is simply... -
Page 18: Planning Of The Installation
(between cores and core effect, that would be able to make the silver-plating on the surface of the to screen) of only 100 pF, we have a total load capacity of 10000 pF. This cable more important, will not have any effect in the audio band. - Page 19 Carrying out the installation figure out what works. In addition, there may be temperature problems in a rack, when several units with high operation temperature are mounted Most of the work is cable assembly, which has to be made carefully.
Need help?
Do you have a question about the SRC 51 and is the answer not in the manual?
Questions and answers