HP D2700 User Manual
  1. Manuals
  2. Brands
  3. HP Manuals
  4. Storage
  5. StorageWorks D2700
  6. User manual

HP D2700 User Manual

Storageworks disk enclosure
Hide thumbs Also See for D2700:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
HP StorageWorks
D2600/D2700 Disk Enclosure User Guide
This guide describes the D2600/D2700 6Gb SAS disk enclosure. Installation, cabling, configuration, and
troubleshooting procedures are included.
Part number: 504227 002
Second edition: February 2010

Advertisement

Table of Contents
loading

Related Manuals for HP D2700

Summary of Contents for HP D2700

  • Page 1 HP StorageWorks D2600/D2700 Disk Enclosure User Guide This guide describes the D2600/D2700 6Gb SAS disk enclosure. Installation, cabling, configuration, and troubleshooting procedures are included. Part number: 504227 002 Second edition: February 2010...
  • Page 2 © Copyright 2009-2010 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.

  • Page 3: Table Of Contents

    Signing up to automatically receive advisories, notices, and other messages ......25 Confirming warranty support and finding out about related services .......... 25 Gathering and recording information ..................25 Planning the storage configuration ..................25 D2600/D2700 Disk Enclosure User Guide...
  • Page 4 7 Cabling examples ................45 Large Form Factor D2600 disk enclosures — maximum capacity configuration ........46 Small Form Factor D2700 disk enclosures — maximum capacity configuration ........47 Dual domain example — best fault tolerance cabling ..............48 Dual domain — best performance cabling ................... 49 Dual domain—alternative cabling ....................
  • Page 5 Replacement instructions ......................59 Exploded view ......................... 59 10 Support and other resources ............61 Contacting HP .......................... 61 Before you contact HP ......................61 HP contact information ......................61 Subscription service ......................61 Documentation feedback ..................... 62 Related information ........................62 Websites ...........................
  • Page 6 Danish notice ........................68 Dutch notice ........................68 Estonian notice ........................69 Finnish notice ........................69 French notice ........................69 German notice ........................69 Greek notice ........................70 Hungarian notice ....................... 70 Italian notice ........................70 Latvian notice ........................70 Lithuanian notice ........................

  • Page 7: Hardware

    • Front status and UID module, page 11 • Power supply module, page 12 • Fan module, page 13 • I/O module, page 14 • Rear power and UID module, page 16 • SAS cables, page 17 D2600/D2700 Disk Enclosure User Guide...

  • Page 8: Small Form Factor Disk Enclosure Chassis

    Small Form Factor disk enclosure chassis Front view 1. Rack-mounting thumbscrews 3. UID push button and LED 2. Disk drive in bay 9 4. Enclosure status LEDs Drive bay numbering Disk drives mount in bays on the front of the enclosure. Bays are numbered sequentially from top to bottom and left to right.

  • Page 9: Large Form Factor Disk Enclosure Chassis

    1. Power supply 1 4. I/O module A 7. UID push button and LED 2. Power supply 2 5. I/O module B 8. Enclosure status LEDs 3. Fan 1 6. Fan 2 9. Power push button and LED D2600/D2700 Disk Enclosure User Guide...

  • Page 10: Disk Drives

    Disk drives A variety of disk drive models are supported for use, including dual-ported and single-ported models. For more information, see the QuickSpecs for the disk enclosure, available on the D2000 website: http://www.hp.com/go/D2000. Disk drives are hot-pluggable. Disk drive LEDs Two LEDs indicate drive status.

  • Page 11: Front Status And Uid Module

    Not being identified or power is off Unit is being identified from 3. UID Blue Blinking the management utility Unit is being identified from Solid the UID button being pushed D2600/D2700 Disk Enclosure User Guide...

  • Page 12: Unit Identification (Uid) Button

    Unit identification (UID) button The unit identification (UID) button helps locate an enclosure and its components. When the UID button is activated, the UID on the front and rear of the enclosure are illuminated. NOTE: A remote session from the management utility can also illuminate the UID. •...

  • Page 13: Fan Module

    One bi-color LED provides module status information. LED color LED status Description No power Blinking The module is being identified Green Solid Normal, no fault conditions Blinking Fault conditions detected Amber Solid Problems detecting the module D2600/D2700 Disk Enclosure User Guide...

  • Page 14: I/O Module

    I/O module The I/O module provides the interface between the disk enclosure and the host. Each I/O module has two ports that can transmit and receive data for bidirectional operation. Small Form Factor I/O module Large Form Factor I/O module 1.
  • Page 15 Enclosure is starting up and not Blinking ready, performing POST Solid Normal, power is on Normal, no fault conditions Blinking A fault of lesser importance 6. Fault Amber A fault of greater importance, Solid I/O failed to start D2600/D2700 Disk Enclosure User Guide...

  • Page 16: Rear Power And Uid Module

    Rear power and UID module The rear power and UID module includes status LEDs, a unit identification (UID) button, and the power on/standby button. Rear power and UID module LEDs LED icon LED color Status Description Not being identified or no power 1.

  • Page 17: Unit Identification (Uid) Button

    Use supported SAS cables with mini-SAS connectors. A variety of SAS cables and cable lengths are supported for use with this disk enclosure. For more information, see the QuickSpecs for the disk enclosure, available on the D2000 website: http://www.hp.com/go/D2000. D2600/D2700 Disk Enclosure User Guide...
  • Page 18 Hardware...

  • Page 19: Technical Specifications

    Input current 2.68 A at 115 VAC typical, 4 A maximum power supply load. The power/heat dissipa- tion for your installation will vary depending Input power on the equipment configuration.) 300 W (max) D2600/D2700 Disk Enclosure User Guide...
  • Page 20 Technical specifications...

  • Page 21: Deployment Types

    Several models of array controller enclosures are supported for use with this disk enclosure. For more information, see the QuickSpecs for the disk enclosure. NOTE: Cabling illustrations are provided elsewhere in this guide, showing a variety of example deployments. Chapter 7 on page 45. D2600/D2700 Disk Enclosure User Guide...
  • Page 22 Deployment types...

  • Page 23: Installation

    A variety of disk drives, SAS controllers, controller enclosures, and SAS cables are supported for use with this disk enclosure. For more information, see the QuickSpecs for the disk enclosure, available on the D2000 website: http://www.hp.com/go/D2000. D2600/D2700 Disk Enclosure User Guide...

  • Page 24: Preliminary Tasks

    Storage management experience is required to successfully install and configure this product. If you are not familiar with installing and configuring storage array systems, HP can install this product for you. For more information, see the Business & IT Services website: http://www.hp.com/go/services.

  • Page 25: Signing Up To Automatically Receive Advisories, Notices, And Other Messages

    Subscriber's Choice website: http://www.hp.com/go/e-updates. Click Subscribe and follow the onscreen instructions to select all of the HP products for which you want to receive notices. While subscribing, indicate your delivery preference (HTML, text, or RSS) and frequency of delivery (as they become available, weekly, or monthly).

  • Page 26: System And Performance Expectations

    Storage planning considerations include: • System and performance expectations • Striping methods • RAID levels • Disk drive sizes and types • Spare drives • Array sizing (capacity) NOTE: For the minimum supported configuration, and other configuration information, see the QuickSpecs for the disk enclosure.

  • Page 27: Disk Drive Sizes And Types

    During the rebuilding process, the array is operating in a reduced state and, unless it is a RAID6 or RAID1+0 array, it cannot tolerate another disk failure in the same array. If another disk D2600/D2700 Disk Enclosure User Guide...

  • Page 28: Array Sizing

    fails at this time, the array becomes inaccessible and information stored there must be restored from backup. After the rebuild of the data onto the spare is completed, when a replacement drive is inserted to replace the failed drive, the system will automatically transfer the data from the spare onto the replacement drive and return the spare to an available-spare state.

  • Page 29: Preparing The Site

    For HP ProLiant server environments, consider using Rack Builder, a software tool that provides a simplified method to planning and configuring racks and rack-mountable products. Rack Builder is available on the Options tab of the ProLiant Home page of the HP servers website: http:// www.hp.com/country/us/eng/prodserv/servers.html.

  • Page 30: Racking The Disk Enclosure

    The disk enclosure can be installed into most standard server racks. To verify that your rack is supported for use with the disk enclosure, see the QuickSpecs for the disk enclosure, available on the D2000 website: http://www.hp.com/go/D2000. CAUTION: Install disk drives in the enclosures only after mounting the enclosures in the rack.

  • Page 31: Racking Procedures

    Slide the device into position on the rails (1) and then tighten the thumbscrews on the front of the device to secure the device to the rack. NOTE: The rear ends of the rails have a bracket that must engage the device chassis to secure the rear of the chassis to the rails. D2600/D2700 Disk Enclosure User Guide...

  • Page 32: Installing Disk Drives In The Enclosure

    Depending on the enclosure model, 12 or 25 disk drives can be installed in the enclosure. A variety of disk drive models are supported for use, including dual-ported and single-ported models. For more information about supported disk drives, see the QuickSpecs for the disk enclosure, available on the D2000 website: http://www.hp.com/go/D2000. Disk drive guidelines CAUTION: Follow industry-standard practices when handling disk drives.
  • Page 33 Determine the status of the hard drive (see Drive status reporting). IMPORTANT: For proper airflow and cooling, a drive blank must remain installed in all unused drive bays. D2600/D2700 Disk Enclosure User Guide...

  • Page 34: Installing Sas Controllers Or Controller Enclosures

    • Install all operating-system-specific service packs, patch kits, or other required tools. • Install HP system management and monitoring tools, such as HP Systems Insight Manager (HP-SIM) and the Array Configuration Utility (ACU). NOTE: For detailed installation and configuration information about the server or the software tools, see the documentation provided with the server or software.

  • Page 35: Connecting Sas Cables And Power Cords

    Use supported SAS cables and power cords. A variety of cables and cable lengths are supported for use with this disk enclosure. For more information, see the QuickSpecs for the disk enclosure, available on the D2000 website: http://www.hp.com/go/D2000. • Use the shortest possible cable between devices. Shorter cables reduce the possibility of signal degradation that might occur over longer distances.

  • Page 36: Connecting Sas Cables To The Server Or Controller Enclosure

    Connecting SAS cables to the server or controller enclosure To connect the first disk enclosure to the server or controller enclosure, use a standard mini-SAS cable. IMPORTANT: When connecting this disk enclosure in a single-domain environment, only the top I/O module (I/O module A) in the disk enclosure is supported for use.

  • Page 37: Connecting Sas Cables To Cascaded Disk Enclosures

    The number of supported cascaded disk enclosures varies per disk enclosure model and installation environment. For more information, see the QuickSpecs for the disk enclosure, controller, or con- troller enclosure, available on the HP storage website: http://www.hp.com/go/storage. Observe the following guidelines: •...

  • Page 38: Connecting Power Cords

    Connecting power cords When connecting power cords, use the cords shipped with the disk enclosure. The power cord should be approved for use in your country. The power cord must be rated for the product and for the voltage and current marked on the electrical ratings label of the product. The voltage and current rating for the cord should be greater than the voltage and current rating marked on the product.

  • Page 39: Powering On The Disk Enclosure

    CAUTION: When you power on the server, the monitor might display a “New Hardware Found” message. Cancel out of this window to prevent the installation of unsupported software. Verify that each component is operating properly. D2600/D2700 Disk Enclosure User Guide...

  • Page 40: Verifying The Operating Status Of The Disk Enclosures

    Verifying the operating status of the disk enclosures To verify that the disk enclosures and disk drives are operating properly, view the enclosure and disk drive LEDs and compare them with the patterns described in the following table. If LED patterns are not as expected, check cable connections between the devices, check the availability of your power source, review the installation procedures, and remove and reinsert the module.

  • Page 41: Configuration

    Which tools are supported for your installation environment is determined by the controller or controller enclosure to which the disk enclosure is connected. For support information, see the QuickSpecs and user documents for the controller or controller enclosure. D2600/D2700 Disk Enclosure User Guide...
  • Page 42 Configuration...

  • Page 43: Operation And Management

    IMPORTANT: When you power on the server, the monitor might display a “New Hardware Found” message. Cancel out of this window to prevent the installation of unsupported software. Verify that each component is operating properly. D2600/D2700 Disk Enclosure User Guide...

  • Page 44: Powering Off Disk Enclosures

    To determine currently-installed firmware and software versions on system components, use management software utilities such as the HP System Management Homepage, HP Systems Insight Manager (HP SIM), Storage Management Utility (SMU), or Command Line Interface (CLI).

  • Page 45: Cabling Examples

    The following basic cabling examples are included: • Large Form Factor D2600 disk enclosures — maximum capacity configuration • Small Form Factor D2700 disk enclosures — maximum capacity configuration • Dual domain example — best fault tolerance cabling • Dual domain — best performance cabling •...

  • Page 46: Large Form Factor D2600 Disk Enclosures - Maximum Capacity Configuration

    Large Form Factor D2600 disk enclosures — maximum capacity configuration This example illustrates cabling for a single-domain configuration. In this configuration, note the following: • P1 on the disk enclosure I/O module is treated as the SAS “in” port. • P2 on the disk enclosure I/O module is treated as the SAS “out”...

  • Page 47: Small Form Factor D2700 Disk Enclosures - Maximum Capacity Configuration

    Small Form Factor D2700 disk enclosures — maximum capacity configuration This example illustrates cabling for a single-domain configuration. In this configuration, note the following: • P1 on the disk enclosure I/O module is treated as the SAS “in” port. •...

  • Page 48: Dual Domain Example - Best Fault Tolerance Cabling

    Dual domain example — best fault tolerance cabling This example illustrates cabling for a dual-domain configuration in a pattern that offers best possible fault tolerance. In this configuration, note the following: • A multi-port, dual-domain controller in the host and dual-port disk drives in the disk enclosure are required for dual-domain deployments.

  • Page 49: Dual Domain - Best Performance Cabling

    When using Large Form Factor disk enclosures, more than one additional disk enclosure can be cascaded. For more information, see the QuickSpecs for the Large Form Factor disk enclosure. Host (server or controller enclosure) Primary disk enclosure Cascaded disk enclosure Primary path Additional path D2600/D2700 Disk Enclosure User Guide...

  • Page 50: Dual Domain-Alternative Cabling

    Dual domain—alternative cabling This example illustrates cabling for a dual-domain configuration in a pattern that offers a balance of fault tolerance and performance. In this configuration, note the following: • A multi-port, dual-domain controller in the host and dual-port disk drives in the disk enclosure are required for dual-domain deployments.

  • Page 51: Troubleshooting

    • Check rear fault LEDs to isolate • Possible error condition exists. failed component. • Contact an authorized service provider for assistance. D2600/D2700 Disk Enclosure User Guide...

  • Page 52: Is The Enclosure Rear Fault Led Amber

    Is the enclosure rear fault LED amber? Answers Possible Reasons Actions Functioning properly. No action required Rear power and UID module might • Be sure that the rear power and not be inserted properly, might UID module is undamaged and have a damaged connector, or is fully seated.

  • Page 53: Is The I/O Module Fault Led Amber

    Fan might not be inserted properly, • Be sure that the fan is undam- might have a damaged connector, aged and is fully seated. or might have failed. • Contact an authorized service provider for assistance. D2600/D2700 Disk Enclosure User Guide...

  • Page 54: Recognizing Disk Drive Failure

    Recognizing disk drive failure In an HP enclosure, a steadily glowing fault LED indicates that a disk drive has failed. Other indications of failed disk drives are as follows: • ACU represents failed drives with a distinctive icon. • HP SIM can detect failed drives remotely across a network. (For more information about HP SIM, see the documentation on the Management CD.)

  • Page 55: Automatic Data Recovery (Rebuild)

    Failure of another drive during rebuild If a non-correctable read error occurs on another physical drive in the array during the rebuild process, the Online LED of the replacement drive stops blinking and the rebuild abnormally terminates. If this D2600/D2700 Disk Enclosure User Guide...

  • Page 56: Handling Disk Drive Failures

    situation occurs, restart the server. The system might temporarily become operational long enough to allow recovery of unsaved data. In any case, locate the faulty drive, replace it, and restore data from backup. Handling disk drive failures If the controller was configured with hardware fault tolerance, complete the following steps after a disk drive failure: Determine which physical drive failed.

  • Page 57: Replacement Procedures

    Verifying component failure • Consult HP technical support to verify that the hardware component has failed and that you are authorized to replace it yourself. • Additional hardware failures can complicate component replacement. Check your management utilities to detect any additional hardware problems: •...

  • Page 58: Identifying The Spare Part

    Optional CSR. You can order the part directly from HP and repair the product yourself, or you can request that HP repair the product. If you request repair from HP, you might be charged for the repair depending on the product warranty.

  • Page 59: Replacement Instructions

    • Placing removed cables on the floor or other surfaces, where they might be walked on or oth- erwise compressed. Replacement instructions Printed instructions are shipped with the replacement part. Instructions for all replaceable components are also posted to the HP website: http://www.hp.com/support/manuals. Exploded view D2600/D2700 Disk Enclosure User Guide...
  • Page 60 Mandatory 8. Fan module interconnect board Mandatory 9. Drive cage Not a CSR part 10. Rear power UID module Mandatory To order a replacement part, contact an HP-authorized service provider or see the HP Parts Store online: http://www.hp.com/buy/parts Replacement procedures...

  • Page 61: 10 Support And Other Resources

    10 Support and other resources Contacting HP Before you contact HP Be sure to have the following information available before you call or contact HP: • Technical support registration number (if applicable) • Product serial number • Product model name and number •...

  • Page 62: Documentation Feedback

    Documentation feedback HP welcomes your feedback. To make comments and suggestions about product documentation, please send a message to storagedocsFeedback@hp.com. All submissions become the property of HP. Related information Websites • http://www.hp.com • HP storage: http://www.hp.com/go/storage • HP support: http://www.hp.com/support •...

  • Page 63: Customer Self Repair

    HP customer self repair (CSR) programs allow you to repair your StorageWorks product. If a CSR part needs replacing, HP ships the part directly to you so that you can install it at your convenience. Some parts do not qualify for CSR. Your HP-authorized service provider will determine whether a repair can be accomplished by CSR.
  • Page 64 Support and other resources...

  • Page 65: 11 Regulatory Compliance Notices

    11 Regulatory compliance notices This section contains regulatory notices for the HP StorageWorks D2600/2700 6Gb SAS disk enclosures. Regulatory compliance identification numbers For the purpose of regulatory compliance certifications and identification, this product has been assigned a unique regulatory model number. The regulatory model number can be found on the product nameplate label, along with all required approval markings and information.

  • Page 66: Modifications

    (European Norms) which are listed on the EU Declaration of Conformity issued by Hewlett-Packard for this product or product family. This compliance is indicated by the following conformity marking placed on the product: Certificates can be obtained from http://www.hp.com/go/certificates. Hewlett-Packard GmbH, HQ-TRE, Herrenberger Strasse 140, 71034 Boeblingen, German Japanese notices...

  • Page 67: Japanese Power Cord Statement

    Japanese power cord statement Korean notices Class A equipment Taiwanese notices BSMI Class A notice Chinese notice Recycling notices English notice D2600/D2700 Disk Enclosure User Guide...

  • Page 68: Bulgarian Notice

    Bulgarian notice Czech notice Danish notice Dutch notice Regulatory compliance notices...

  • Page 69: Estonian Notice

    Estonian notice Finnish notice French notice German notice D2600/D2700 Disk Enclosure User Guide...

  • Page 70: Greek Notice

    Greek notice Hungarian notice Italian notice Latvian notice Regulatory compliance notices...

  • Page 71: Lithuanian Notice

    Lithuanian notice Polish notice Portuguese notice Romanian notice D2600/D2700 Disk Enclosure User Guide...

  • Page 72: Slovak Notice

    Slovak notice Spanish notice Swedish notice Turkish notice Türkiye Cumhuriyeti: EEE Yönetmeliğine Uygundur Regulatory compliance notices...

  • Page 73: Index

    D2600/D2700 Disk Enclosure User Guide...
  • Page 74 39, power cord I/O module defined, power on/standby button LEDs, defined, installation location, assistance, HP, operation, in the rack, power requirements, of disk drives, power supply module installing defined, hard drives, LEDs, powering off,...
  • Page 75 46, software utilities, supported, specifications environmental, general, power, startup sequence, 39, status rear power and UID module, disk drives, fan module, front status and UID module, I/O module, power supply module, structural support, D2600/D2700 Disk Enclosure User Guide...

This manual is also suitable for:

D2600

Table of Contents