Panasonic WV-CW474A Operating Instructions

FEATURES

1. The following functions are built in.
(1) Auto Light Control (ALC)
(2) The SUPER-D2 function eliminates interference by strong background lighting which
Color CCTV Cameras
makes the camera picture dark, such as a spotlight.
Dynamic range of 46 dB (Typ)
Operating Instructions (3) Internal, Line-Locked, Multiplexed Vertical Drive (VD2) Sync
(4) Auto/Manual White Balance Function
(5) Electronic Shutter Function
2. Signal-to-noise ratio of 50 dB (Equivalent to AGC Off)
3. Minimum illumination of 2.0 lx (0.20 footcandle) (WIDE) (Color mode)
WV-CW474AF
Minimum illumination of 0.2 lx (0.02 footcandle) (WIDE) (Black-and-white mode)
Model Nos.
Minimum illumination of 0.8 lx (0.08 footcandle) (WIDE) with the WV-CW2C optional dome cover
WV-CW474AS (Color mode)
Minimum illumination of 0.1 lx (0.01 footcandle) (WIDE) with the WV-CW2C optional dome cover
(Black-and-white )
4. 480 lines of horizontal resolution (Color normal mode)
Before attempting to connect or operate this product, 510 lines of horizontal resolution (Color High Resolution mode)
please read these instructions carefully and save this manual for future use. 570 lines of horizontal resolution (Black-and-white mode)
5. High quality picture:
(a) 2H type vertical enhancer for greater picture sharpness
N0204-1034 3TR002376BAA Printed in Japan
(b) Chroma averaging circuit for better color signal-to-noise ratio
(c) Minimum of aliasing on fine objects
(d) Expanded dynamic range by use of knee circuit
(e) Highlight aperture correction for greater picture detail of bright objects
Caution:
Before attempting to connect or operate this 6. Selectable electronic sensitivity enhancing modes including AUTO, MANUAL and OFF
product, please read the marking on the top. 7. Built-in Digital Motion Detector
For U.S.A
8. Auto black-and-white mode enables the camera to switch between color and black-and-white
NOTE: This equipment has been tested and found
picture in response to Light input.
to comply with the limits for a Class A digital
9. Electronic zoom function magnifies a scene 2-fold and changes the angle of view.
device, pursuant to Part 15 of the FCC Rules.
CAUTION
These limits are designed to provide reasonable
protection against harmful interference when the
RISK OF ELECTRIC
equipment is operated in a commercial environ-
SHOCK DO NOT OPEN

MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS

ment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed
and used in accordance with the instruction manu-
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, al, may cause harmful interference to radio com-
munications.
DO NOT REMOVE COVER (OR BACK).
Operation of this equipment in a residential area is
NO USER-SERVICEABLE PARTS INSIDE. REFER SER-
likely to cause harmful interference in which case
VICING TO QUALIFIED SERVICE PERSONNEL.
the user will be required to correct the interference
at his own expense.
FCC Caution: To assure continued compliance,
The lightning flash with arrowhead
(example - use only shielded interface cables when
symbol, within an equilateral trian-
connecting to computer or peripheral devices). Any
gle, is intended to alert the user to
changes or modifications not expressly approved
the presence of uninsulated "dan-
by the party responsible for compliance could void
gerous voltage" within the product's
the user's authority to operate this equipment.
enclosure that may be of sufficient
SA 1965 magnitude to constitute a risk of
electric shock to persons.
The serial number of this product may be found on
the top of the unit.
You should note the serial number of this unit in the
The exclamation point within an
space provided and retain this instruction as a per-
equilateral triangle is intended to
manent record of your purchase to aid identification
alert the user to the presence of
in the event of theft.
important operating and mainte-
nance (servicing) instructions in the
Model No.
literature accompanying the appli-
ance. Serial No.
SA 1966
WARNING: To prevent fire or electric shock hazard, do not expose this appliance to rain or moisture.
The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such
as vases, shall be placed on the apparatus.
PREFACE
Panasonic's WV-CW474AF/CW474AS series color digital camera introduces a new level of high pic-
ture quality and high resolution through the use of a 1/3-inch interline transfer CCD image sensor
having 768 horizontal pixels (picture elements), and digital signal processing LSIs. This model
offers cutting-edge technology for advanced video surveillance.

PRECAUTIONS

1. Do not attempt to disassemble the camera.
To prevent electric shock, do not remove screws or covers.
There are no user-serviceable parts inside. Ask qualified service personnel for servicing.
2. Handle the camera with care.
Do not abuse the camera. Avoid striking, shaking, etc. The camera could be damaged by
improper handling or storage.
3. The installation should be made by qualified service personnel or system installers.
4. Do not use strong or abrasive detergents when cleaning the camera body.
Use a dry cloth to clean the camera when dirty. When the dirt is hard to remove, use a mild
detergent and wipe gently. Then wipe off the remaining detergent with a dry cloth.
5. Clean the lens with care.
Do not clean the lens with strong or abrasive detergents. Use lens tissue or a cotton tipped
q Panning table
applicator and ethanol.
Adjusts the panning angle of the camera.
6. Never face the camera towards the sun.
w Pan lock screw
Do not aim the camera at bright objects. Whether the camera is in use or not, never aim it at
Fixes the panning position.
the sun or other extremely bright objects. Otherwise, blooming or smear may be caused.
e Tilting lock screw
7. Do not operate the camera beyond the specified temperature, humidity or power source
Fixes the tilting position.
ratings.
Use the camera at temperatures within –10 °C to +50 °C (14 °F - 122 °F), and humidity below
r AZIMUTH (Angle adjuster)
90 %. The input power source is 24 V AC or 12 V DC.
Shoots in a straight-angle field of view when aiming at an object in a slanting direction even if
the tilt angle has been set.
8. Turn the circuit breaker off which supplies the camera with the power when abnormal
conditions are encountered.
t Zoom lock lever
Fixes the zoom position.
y Focus lock lever
Caution:
Fixes the focus position.
To prevent fire or electric shock hazard, use a UL listed cable (VW-1, style 1007) for
the 24 V AC Input Cable. u LEFT button (I) (L)
Moves the cursor to the left, selects the mode and adjusts some levels.
i RIGHT button (I) (R)
Moves the cursor to the right, selects the mode and adjusts some levels.
o UP button (I) (U)
Moves the cursor upward and selects items in the CAM SET UP menu.
!0 DOWN button (I) (D)
Moves the cursor downward and selects items in the CAM SET UP menu.
!1 SET button (I) (S)
Activates an item selected in the CAM SET UP menu.
!2 BW AUTO1 LEVEL switch (SW5)
Selects the illuminance level in LOW or HIGH mode for B/W. The factory default setting is HIGH.
!3 BW switch (SW4)
Switches to AUTO1 between color and black-and-white picture in response to light input. The
factory default setting is OFF.
!4 AP gain switch (SW3)
Selects the aperture gain level to SHARP or SOFT. The factory default setting is SHARP.
!5 UPSIDE DOWN switch (SW2)
Turns the picture upside down by selecting ON. The factory default setting is OFF.
!6 Sync switch (SW1)
Switches internal sync (INT) mode or line-lock (LL) mode. The factory default setting is INT.
!7 Monitor output Jack (3.5 Diam. mini jack)
Connects the LCD monitor and such devices with 3.5 diam. 2-pole L-type plug for checking
images.
!8 Optional heater connector DC out
When an optional heater unit is installed in the camera, the harness exiting from the unit will be
connected to this.
y e
t
q
r
w
!8
u
L
EFT
i R
IGHT
LOW OFF SHARP OFF INT
o
U
P
!0
D
OWN
!1 HIGH AUTO1 SOFT ON LL
!9 Power cable (24 V AC or 12 V DC)
SET !5
Cautions:
!4
1. Connect to 12 V DC (10.5 - 16 V) or 24 V AC (19.5 V-28 V) class 2 power supply only. Make
!3
sure to connect the grounding lead to the GND terminal when the power is supplied from a
!6
24 V AC power source.
!2
2. To prevent fire or electric shock hazard, use a UL listed cable (VW-1, style 1007) for the Input
Terminal.
!7
@0 Power cable for heater unit WV-CW3H (24 V AC)
Cautions:
1. Connect to 24 V AC (19.5 V-28 V) class 2 power supply only.
2. To prevent fire or electric shock hazard, use a UL listed cable (VW-1, style 1007) for the Input
Terminal.
@1 Video output cable with BNC connector
Connects with the video connector of the monitor.
@2 Dome cover
@3 Camera mounting bracket
The WV-CW474AS is supplied with a mounting bracket for ceiling installation.

SETUP

1. CAMERA SETUP MENU
This camera utilizes an on-screen user setup menu.
• Opening the Setup Menu
Press and hold down I(S) for 2 seconds or
more.
The CAM SET UP menu appears on the monitor as
shown at right.
Check the current settings on the menu.
Refer to the following sections for a detailed description of menu items. If you decide not to make
any changes after checking the current settings, move the cursor to END in the bottom line, and
press I(S) to close the setup menu.
Note: If no button is pressed for 5 minutes while a setup menu is being displayed on the monitor
screen, it is automatically closed and the mode returns to the normal camera picture.
2. SETUP OPERATION
This camera utilizes an on-screen user setup menu (CAM SET UP). To set items on the CAM SET
UP menu, use the following buttons on the side panel.
Left Button (I) (L): Moves the cursor to the left. Use this button to select or adjust the para-
meters of the selected item. The parameter changes each time this button
is pressed.
Right Button (I) (R): Moves the cursor to the right. Use this button to select or adjust the para-
@0 meters of the selected item. The parameter changes each time this button
!9
is pressed.
Up Button (I) (U): Moves the cursor upwards. Use this button to select an item or adjust the
@1
parameters.
Down Button (I) (D): Moves the cursor downwards. Use this button to select an item or adjust
the parameters.
Set Button (I) (S): Executes selections and displays a submenu for an item with the
mark.
• To reset the parameter to the factory default setting, move the cursor to the parameter to be
reset and press I(L) and I(R) simultaneously.
• To return to the previous menu or page, move the cursor to RET and press I(S).
• To close the setup menu, move the cursor to END and press I(S).
• All Reset Operation
All Reset allows you to reset all setup menu items to the factory default settings if you are unsure
about the correct settings. Proceed as follows:
(1) Make sure that the CAM SET UP menu is not displayed (a camera picture is displayed).
@2 (2) While pressing both I(L) and I(R), press I(S) for a few seconds. The message ALL
RESET momentarily appears on the monitor screen.
This resets all adjustments and parameters to the factory default settings except for the PIX
OFF setting.
• Editing the CAM SET UP Menu
Important Notice:
When SET UP DISABLE appears in the bottom line of the CAM SET UP menu, you cannot
change the currently active settings. This is to prevent accidental changing of the settings.
To edit the CAM SET UP menu (change settings), press I(U) and I(D) or I(L) and I(R) to
@3 move the cursor to SET UP DISABLE in the bot-
tom line.
** CAM SET UP **
Press I(S). SETUP DISABLE changes to CAMERA ID
ALC
SHUTTER
SETUP ENABLE. Move the cursor to DIP SW.
AGC
Press I(S). DIP SW changes to MENU. Then SENS UP
SYNC
WHITE BAL
move the cursor to the item(s) you want to
MOTION DET
change.
DIP SW
END
Notes:
• When DIP SW is selected for CAM SET UP menu, five modes can be set with the DIP switches.
• To operate the camera functions with the system controller, select MENU in the CAM SET UP
menu.
Important Notice:
When the setup menu is closed after changing the parameters in the menu, the new values are
stored in the EEPROM (Electrically Erasable and Programmable Read-Only Memory). These
values remain valid until new values are stored, even if the power of the camera is off.
Setting Procedures
1. Camera Identification (CAMERA ID) Setting
You can use the camera identification (CAMERA ID) to assign a name to the camera. The camera
ID consists of up to 16 alphanumeric characters. The camera ID display can be switched on or off
on the monitor screen.
To edit the CAMERA ID
** CAM SET UP **
1. Move the cursor to CAMERA ID.
CAMERA ID OFF
ALC ALC
The factory default setting is OFF.
SHUTTER ---
AGC ON(HIGH)
2. Press I(S). The CAMERA ID menu appears.
SENS UP OFF Character Cursor
SYNC INT The cursor on the letter "0" is highlighted.
WHITE BAL ATW1
0123456789
MOTION DET OFF 3. Move the cursor to the character you want to edit
ABCDEFGHIJKLM
by pressing I(L) / I(R) / I(U) / I(D).
NOPQRSTUVWXYZ
DIP SW
().,'":;&#!?=
END SET UP DISABLE 4. After selecting the character, press I(S). The +-*/%$
selected character appears in the editing area. SPACE
POSI RET END RESET
(The pointer in the editing area moves to the right
................
automatically at this moment.)
Pointer
5. Repeat the steps above until all characters are
edited. CAMERA ID menu
To enter a blank space in the CAMERA ID
Move the cursor to SPACE and press I(S).
To replace a specific character in the CAMERA ID
1. Move the cursor to the editing area by pressing I(D).
2. Move the pointer to the character to be replaced by pressing I(L) or I(R). Then move the
cursor to the character area and select a new character.
3. Press I(S) to determine the CAMERA ID.
To erase all characters in the editing area
Move the cursor to RESET and press I(S). All characters in the editing area disappear.
To determine the display position of the CAMERA ID
1. Move the cursor to POSI, and press I(S). The display at right appears and the CAMERA ID
is highlighted.
2. Move the CAMERA ID to the desired position by
pressing I(L) / I(R) / I(U) / I(D). Highlighted
3. Press I(S) to fix the position of the CAMERA
ID. The mode returns to the previous CAMERA ID
menu.
WV-CW474A
Notes:
• The CAMERA ID stops at the edges of the
monitor screen.
• The CAMERA ID moves faster if any of I(L) / I(R) / I(U) / I(D) is kept pressed
for a second or more.
2. Light Control Setting (ALC)
2-1. ALC Mode with SUPER-D2 ON
Super Dynamic2 Function (SUPER-D2)
The important object in a scene is usually placed in the center of the monitor screen. In the SUPER-
D2 mode, more photometric weight is given to the center of the screen (where the important object
is located) than to the edge of the screen (where a bright backlight would most likely be located).
The SUPER-D2 function eliminates interference by strong background lighting which makes the
camera picture dark, such as a spotlight.
1. Move the cursor to ALC and press I(S). The ALC CONT menu appears.
2. Move the cursor to SUPER-D2 and select ON.
** CAM SET UP **
OFF CAMERA ID OFF
ALC ALC ALC 3. If you want to adjust the video output level,
---
SHUTTER --- ** ALC CONT **
ON(HIGH)
AGC ON(HIGH) move the "I" cursor for LEVEL. Adjust to the BACK LIGHT COMP
OFF SENS UP OFF
INT SYNC INT desired level by pressing I(L) or I(R). SUPER-D2
ATW1 WHITE BAL ATW1
OFF MOTION DET OFF
MENU LEVEL
SET UP DISABLE END SET UP ENABLE
RET END
Character
Area
Command
Editing
Area
ON
...I.....
- +
(To be continued reverse page)