Table of Contents
Advertisement
Specifications
Power supply:
DC 1 V
(when external power is supplied)
AC 150 V - 40 V
(when CCU is connected)
Power consumption: 8 W (during external power
supply operation, camera only)
70 W (when CCU is connected)
indicates safety information.
Ambient temperature range:
–10 °C to +45 °C
[Preheating required at temperatures
below 0 °C]
Storage temperature range:
–0 °C to +60 °C
Operating ambient humidity:
Less than 85 %
Weight:
Approx. 4.7 kg
Dimensions:
15 60 60 mm
(W H D)
[excluding protrusions]
Basic items
1) Pickup device:
/˝ . million pixel IT-CCD
) System:
GBR pickup system
) Colour separation optical system:
f/1.4 prism
4) Optical filters:
CC: 00K, 400K, 600K, Cross,
Diffusion
ND: CAP, Through, 1/4, 1/16, 1/64
5) Lens mount:
Bayonet type
6) Output standard: SMPTE 9M
7) Sensitivity:
f/10.0, 000 lux, 00K,
white reflectance 89.9 %
(Vertical frequency: 59.94 Hz)
8) Horizontal modulation:
More than 50 % (7.5 MHz)
9) S/N ratio:
60 dB typ. (Y: 0 MHz)
10) Horizontal frequency:
.716 kHz, 115-line frame
(Vertical frequency: 59.94 Hz)
8.15 kHz, 115-line frame
(Vertical frequency: 50 Hz)
11) Vertical frequency:
59.94 Hz or 50 Hz, interlace
Input/output signals
1) MIC input:
–60 dBu to +4 dBu
(XLR -pin female )
Gain selected by camera menu
) INCOM:
Input: –60 dBu to –10 dBu
Output: 100 mW max
(XLR, 5-pin female )
(Mixing is controlled separately for
PGM1 and PGM.)
) HD-SDI1/HD-SDI output:
HD signal = 0.8 V [p-p], 75 ohms (BNC)
The HD-SDI signal output can be
added to the regular images using the
camera menu item setting and switched
to the VF or RET image output.
4) Prompt output:
VBS signal = 1 V [p-p], 75 ohms (BNC)
G/L input:
Tri-level SYNC or black burst (BNC)
Selected using a switch.
5) AUX BNC
• HD RET input: HD analogue signal = 1 V [p-p],
75 ohms (BNC)
• Prompt output: VBS signal = 1 V [p-p], 75 ohms (BNC)
(When the CCU has a Prompt input)
• Down converter output (supported as an option):
VBS or D1 signal = 1 V [p-p] or
0.8 V [p-p], 75 ohms (BNC)
Input or output can be selected using
the camera menu item setting.
6) DC OUT:
1 V, MAX. 1 A
Control
1) Power selection: CCU, OFF, EXT
) USER 1, , :
Functions specified by menu items can
be allocated to the switch.
) RET A/B selection:
For selecting the return signal
4) Monitor selection: Y/C, NAM, R, G, B
5) RET, PTT SW:
RET, PTT
6) Gain selection:
LOW, MID, HIGH
7) Output selection: CAM, BAR, TEST
8) White balance mode:
A, B, preset
9) Shutter speed selection:
1/60, 1/100, 1/15, 1/50, 1/500,
1/1000, 1/1500, 1/000
10) AWB, ABB settings
11) Menu selection
1) CALL SW
1) INCOM:
MIC ON/OFF, receiving level or PGM
level
14) MIC setting:
MIC power, MIC gain, MIC1 selection
15) Optical filter setting:
REM, LOCAL selection and LOCAL
setting
16) Back light SW (rear panel):
ON/OFF
* When the CCU is connected, the selection functions
for 6) to 10) are not effective.
Control is exercised from the ROP or MSU.
Weight and dimensions shown are approximate.
4
Advertisement
Table of Contents
