Licence; Faqs; Specifi Cations - Panasonic Vieta TX-26LXD70A Operating Instructions Manual

FAQs

Problem
•
Digital TV reception technology requires high quality, robust DTV signals which in some domestic aerial
installations, may be relatively poor despite good analogue reception.
Aerial connection when using
DTV and VCR / DVD Recorder
After DVB Auto Tuning only
some or no DVB channels are
found
Picture regularly breaks up on
some channels, or
"No Signal" message
Picture very infrequently
breaks up on some or all
channels
TV takes so long to turn on
The channel cannot be changed
The channel cannot be selected
TV goes into "Standby mode"
The remote control does not work
38
Actions
•
To maintain optimum signal quality from TV aerial, use a TV aerial splitter
(as illustrated) when connecting two or more equipments to the same aerial.
TV
(Individual aerial)
Splitter
Aerial Output
Aerial
Input
Aerial Input
Aerial Output
terminal
VCR
(Individual aerial)
•
Check to ensure your area is covered by DVB transmissions.
• (www.dba.org.au/)
Check that the aerial and antenna cable are designed for DVB.
For your safety, the aerial and cable should be inspected / installed by a
licenced installer that should comply with Australian Standard AS1417.1.
Note: If you live within 5-10 Km of DVB transmission towers, a
combined VHF / UHF aerial should be adequate. Outside this area,
separate VHF and UHF aerials provide superior reception performance.
•
If you live in a unit or apartment, check to ensure the Master
Antenna TV (MATV) system is designed for analogue and DVB-T
reception. Please consult your body corporate. (www.dba.org.au/)
•
Check "Signal Display". (p. 25)
If "Signal Quality" or "Signal Strength" are displayed in red or
constantly changing, check aerial.
If problem persists consult your local TV aerial installer.
•
Check that the aerial and antenna cable are designed for DVB.
For your safety, the aerial and cable should be inspected / installed by a
licenced installer that should comply with Australian Standard AS1417.1.
•
Interference (known as impulse noise) from household appliances
such as light switches, fridges etc may cause picture break up and /
or audio distortion. Use high quality quad shielded coaxial cable fl y
lead between TV and antenna wall socket to minimise impulse noise
• pickup. If problem persists consult your local TV aerial installer.
When "No Signal" message is displayed check TV aerial connection.
•
The received signal may be too weak to allow the TV to reliably lock to the
desired "No Signal" channel to generate a stable picture. Repeat the tuning
procedure (p. 24). If problem persists consult your local TV aerial installer.
•
Electrical atmospheric interference caused by local or distant
lighting storms or heavy rain with wind in "leafy" locations may
cause pictures to break up and audio to mute or distort momentarily.
•
Impulse noise interference from an infrequently used electrical appliance,
or a passing vehicle or lawn mower with a "noisy" ignition system.
•
Like your computer, the TV has to run a number of diagnostic and
software checks before it can display any broadcast channels.
•
Is the TV in Teletext mode? (p. 16)
•
Is the channel locked? (p. 25)
•
Off Timer function is activated.
•
The TV enters "Standby mode" about 30 min. after broadcasting ends.
•
Are the batteries installed correctly? (p. 6)
•
Has the TV been switched On?

Licence

• Trademark Credits
• DVB is a trademark of the DVB Digital Video Broadcasting Project (1991 to 1996).
• VGA is a trademark of International Business Machines Corporation.
• Macintosh is a registered trademark of Apple Computer, USA.
S-VGA is a registered trademark of the Video Electronics Standard Association.
• Even if no special notation has been made of company or product trademarks, these trademarks have been fully respected.
HDMI, the HDMI Logo and High-Defi nition Multimedia Interface are trademarks or registered trademarks of HDMI
• Licensing LLC.
• HDAVI Control TM is a trademark of Matsushita Electric Industrial Co., Ltd.
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby Laboratories.
Specifi cations
TX-26LXD70A
Power Source AC 220-240 V, 50 / 60 Hz
Average use 98 W
Standby condition 0.4 W
Aspect Ratio 16:9
66 cm (diagonal)
Visible screen size
575 mm (W) × 323 mm (H)
Number of pixels 1,049,088 (1,366 (W) × 768 (H))
Speaker 120 mm × 60 mm × 2 pcs
Audio Output 20 W (10 W + 10 W )
Headphones M3 (3.5 mm) stereo mini Jack × 1
VGA, SVGA, XGA
SXGA ······ (compressed)
PC signals
Horizontal scanning frequency 31 - 69 kHz
Vertical scanning frequency 59 - 86 Hz
PAL B/G Reception of Off air broadcasts
DVB-T 7 MHz VHF / UHF (Australia) free-to-air TV broadcast reception
Receiving Systems /
PAL 60 Hz Playback of NTSC tape from some PAL Video recorders (VCR)
Band name
M.NTSC Playback from M. NTSC Video recorders (VCR)
NTSC Playback from NTSC Video recorders (VCR)
Aerial - Rear Standard Belling & Lee connector
Temperature : 0 °C - 35 °C
Operating Conditions
Humidity : 20 % - 80 % RH (non-condensing)
RCA PIN Type × 2
AUDIO L - R
AV1
VIDEO RCA PIN Type × 1
Input
S VIDEO Mini DIN 4-pin
AUDIO L - R RCA PIN Type × 2
AV2 VIDEO RCA PIN Type × 1
Input
Y
COMPONENT
P /C , P /C
B B R R
AUDIO L - R RCA PIN Type × 2
RCA PIN Type × 1
AV3 VIDEO
Input
Y
COMPONENT
P /C , P /C
B B R R
AUDIO L - R RCA PIN Type × 2
AV4
VIDEO RCA PIN Type × 1
Input
S VIDEO Mini DIN 4-pin
AUDIO L - R
Monitor RCA PIN Type × 2
Output
VIDEO
RCA PIN Type × 1
HDMI1 / 2 Input TYPE A Connectors
HIGH-DENSITY D-SUB 15PIN
PC Input
Others
Audio Input RCA PIN Type × 2
DIGITAL AUDIO OUT PCM / Dolby Digital, Fiber optic
657 mm × 525 mm × 239 mm (With TV Stand)
Dimensions ( W × H × D )
657 mm × 473 mm × 117 mm (TV only)
Mass 14.5 k Net
Note
•
Design and Specifi cations are subject to change without notice. Weight and Dimensions shown are approximate.
TX-32LXD70A
134 W
80 cm (diagonal)
697 mm (W) × 392 mm (H)
0.5 V[rms]
1.0 V[p-p] (75 Ω)
Y:1.0 V[p-p] (75 Ω) C:0.286 V[p-p] (75 Ω)
0.5 V[rms]
1.0 V[p-p] (75 Ω)
1.0 V[p-p] (including synchronization)
±0.35 V[p-p]
0.5 V[rms]
1.0 V[p-p] (75 Ω)
1.0 V[p-p] (including synchronization)
±0.35 V[p-p]
0.5 V[rms]
1.0 V[p-p] (75 Ω)
Y:1.0 V[p-p] (75 Ω) C:0.286 V[p-p] (75 Ω)
0.5 V[rms] (high impedance)
1.0 V[p-p] (75 Ω)
•
This TV supports "HDAVI Control 2" function.
R, G, B/0.7 V[p-p] (75 Ω)
HD, VD/TTL Level 2.0 - 5.0 V[p-p] (high impedance)
0.5 V[rms]
791 mm × 615 mm × 248 mm (With TV Stand)
791 mm × 563 mm × 117 mm (TV only)
17.5 k Net
39